Electrolux Dryer Filter

The Lint Filter is an OEM part for Frigidaire dryers. This component is crucial for trapping lint and debris that come off clothes during the drying process. By capturing this lint, the filter prevents it from clogging the dryer’s internal mechanisms and vent, thereby enhancing the efficiency of the dryer and reducing the risk of fires. 

Symptoms of a bad Lint Filter include:

• Excessive lint escaping back into the dryer drum or venting system.
• Tears or holes in the filter mesh that fail to trap lint.
• Difficulty fitting the filter into its slot due to warping or damage.
• Longer drying times or overheating, indicating poor air flow.

Causes of a bad lint filter can include normal wear and tear from regular cleaning and use, accidental damage during removal or cleaning, or degradation from exposure to high heat.

The Lint Filter is an OEM replacement part for Frigidaire, Electrolux, Gibson, and Kenmore dryers.

The Lint Filter is an OEM component for Frigidaire dryers. As an important safety component, the lint filter screens out lint and other debris from the airflow before it exits the dryer. Trapping lint inside the filter helps reduce fire hazards and maintains peak airflow for more efficient drying performance.

Symptoms of a bad lint filter include:

• Excessive drying times as airflow is reduced
• Buildup of lint inside the dryer cabinet beyond the filter screen
• Lint escaping from the back of the dryer and collecting outside
• The lint filter itself is cracked or damaged

Causes of a lint filter issue include failure to clean the filter after each use, resulting in a blockage over time. Natural wear and tear or accidental damage can also render the filter unusable.

This OEM Frigidaire replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Lint Filter Kit is an OEM part compatible with Frigidaire electric dryers. This kit includes both a lint filter screen and housing assembly. 

Causes of a bad lint filter include blockages from excess lint that the filter cannot effectively remove. Small tears or openings in the filter mesh can also bypass lint rather than capture it.

Symptoms of a clogged or damaged lint filter include: 

• Slow or incomplete drying times  
• Excessive moisture left in clothes after a full cycle
• Reduced airflow noticed around the lint filter area
• Visible lint buildup inside the dryer cabinet

This OEM replacement is compatible with Frigidaire, Electrolux, Gibson, Kelvinator and some Kenmore dryers for a direct fit solution.

The Lint Trap is an OEM part for Frigidaire dryers. It helps in capturing lint and debris generated during the drying process, preventing them from clogging the dryer vent and exhaust system.

Causes of a clogged or faulty lint trap can include excessive lint accumulation, damage to the trap screen, or improper installation.

Symptoms of a bad lint trap may include:

• Longer drying times
• Reduced drying efficiency
• Visible lint accumulation in the dryer drum or on clothes
• Excessive heat inside the dryer

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Color: white. It measures about 13 inches wide by 11-1/2 inches high.

This line noise filter conditions incoming AC power by reducing electromagnetic interference before it reaches the appliance's electronics. Replacing a shorted or damaged filter can restore stable operation and help prevent erratic control behavior.

• Filters EMI/RFI on the power line before it reaches the control system
• Helps protect sensitive electronics from interference and voltage spikes
• Failure may present as no power, intermittent resets, or nuisance GFCI/breaker trips
• Typically mounted near the power-cord entry; also called a line filter

• Disconnect power and allow any capacitors to discharge before servicing
• Note wire positions and line vs. load orientation; take a photo before removal
• Secure the ground and mount the new filter firmly to the chassis
• Route and reconnect wires carefully to avoid pinching; reassemble and test

Replacement grill trim that restores your appliance's exterior finish and helps direct airflow. Use this grill when the original piece is cracked, missing, loose, or cosmetically damaged to regain a clean, finished appearance. What it does:

• Covers and protects internal components behind the appliance front or vent area.
• Helps direct airflow and reduce drafts around the appliance opening.
• Prevents debris or fingers from contacting internal parts.
• Stops rattling or vibration caused by a bent or loose grill.
• Restores the appliance's original look when the factory grill is damaged.

• Disconnect power at the breaker and allow the appliance to cool before starting any work.
• Remove existing fasteners or clips; retain original screws if they are reusable.
• Align the new grill, then secure with the original hardware; avoid over-tightening to prevent cracking.