Electrolux Dryer Control Board

The Control Board is an OEM replacement part for Frigidaire dryers. It is the central processing unit that controls all functions and operations of the dryer. The board receives input from sensors, activates heating elements and motor controls, and determines dryness levels based on temperature, moisture, and time settings. 

Causes of a bad control board can include failure due to wear and tear over time, exposure to heat and electrical stresses during normal operating cycles, as well as damage due to external impact or moisture intrusion. 

Symptoms of a bad control board include: 

• The dryer not starting or powering on
• Display/touchpad malfunctions 
• Failure to progress through cycles
• Inability to achieve set heat or time settings
• Erratic programs or operation

This OEM replacement is also compatible with Electrolux and some Kenmore model dryers.

This electronic control board is the machine's brain, directing power and timing for each selected cycle. Replacing it restores responsive controls and reliable operation.

• Directs power to motors, valves, heaters, pumps, and fans per cycle selection
• Interprets inputs from sensors and switches to adjust operation
• Stores and executes timing/logic and manages error routines
• Failure symptoms include unresponsive controls/display, won't start, stops mid-cycle, cycle won't advance, intermittent operation, or error codes

• Disconnect power at the breaker before servicing; verify zero voltage.
• Use ESD protection and handle the board by the edges only.
• Photograph/label wiring and transfer connectors one by one to the new board.
• Mount securely in the existing bracket/enclosure, restore power, and run a test; for any model-specific resets.

Dryer won't turn off or advance cycles? This control timer regulates cycle progression and automatic shutoff. Moderate DIY repair restores timing.

This is a replacement dryer control board for an electric dryer. The dryer control board is the main electrical board that controls all the primary functions of a dryer. If the dryer has stopped working properly or is no longer turning or heating, this could mean that the dryer control board needs replaced. To replace the board, make sure the dryer is turned off and removed from power. The dryer control board will be located either on the back of the dryer or behind the user interface. Accessing it will require a screwdriver.This authentic OEM replacement part can be used in many models including the Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse and others.

Dryer won't start, stops mid-cycle, or shows error codes? This control board manages all dryer functions and cycles. Moderate difficulty repair.

Dryer won't start, stops mid-cycle, or displays error codes? The control board monitors temperature, moisture, and cycle timing. Moderate DIY repair.

Fix a dryer that won't start, stops mid-cycle, or has no display. This main control board manages all electronic functions. Moderate DIY repair.

Fixes unresponsive controls, non-functioning display, or dryer that won't start. This main control board restores all user interface functions and cycles.

This main electronic control board manages oven functions and user commands so your range responds correctly to temperature settings, timers, and cooking modes. Replaces a failed board to restore control and display operation. What it does:

• Receives input from the front control panel and regulates oven heating cycles and timers
• Controls bake, broil and other cooking modes by sending power signals to heating elements
• Can cause a blank display, unresponsive touchpad/buttons, or failure to start if defective
• May trigger control-related error codes or intermittent operation when malfunctioning

• Disconnect power at the breaker or unplug the appliance before any service
• Handle the board carefully; avoid static discharge and contact with circuit traces
• Basic appliance disassembly and wire-labeling required; verify connections match before reassembly

This user interface control board replaces the oven's front control module so you can send commands and view settings. It restores responsive touch/buttons and proper display feedback for normal operation. What it does

• Receives button/touch inputs and relays commands to the oven control system
• Provides display/status feedback so settings and timers are visible
• Helps resolve unresponsive buttons, blank or incorrect display readouts, or intermittent control behavior
• Works as the main input surface for oven functions like bake, broil, timers, and temperature settings

• One user interface control board (UI board) — only items explicitly listed by the manufacturer are included

• Turn power to the appliance off at the breaker before servicing to avoid electrical shock
• Handle the board and connectors carefully; avoid touching contacts or flexing the board
• Verify connector orientation and secure mounting; test operation with power restored

Fix E91 communication errors, no heat issues, or unresponsive dryer controls. This interface board processes cycle settings and houses the display.

Fixes dryer that won't start, runs continuously after timer ends, or has flashing display lights. Direct control board replacement. 20-minute DIY repair.

Fix a dryer that won't shut off or advance through cycles with this mechanical timer. Controls cycle sequencing and timing. Moderate DIY install.

Fixes unresponsive controls, display errors, or cycle failures in your dryer. This control board restores reliable operation of all functions and settings.