Electrolux Microwave Parts

This replacement cam is the small pivot piece that helps a refrigerator door hinge open and close smoothly and keep the door aligned. Installing the cam restores proper hinge movement for a secure, even door fit. What it does:

• Acts as the hinge pivot point to guide door rotation and alignment
• Helps prevent door sagging, binding, or uneven gaps
• Reduces noisy or rough hinge movement caused by a worn cam
• Works with the hinge assembly to maintain proper door sealing

• One cam

• Disconnect power to the appliance or unplug before starting any work
• Support the door while removing hinge fasteners to prevent damage or injury
• Inspect mating hinge surfaces and replace any damaged hardware for best results
• Tighten hinge fasteners to manufacturer torque and check door alignment after installation

This holder is a small mounting bracket that secures internal appliance components to prevent movement and maintain proper alignment, helping reduce noise and keep parts functioning reliably. What it does:

• Secures and positions an internal component or assembly to the appliance frame
• Prevents shifting or sagging that can cause rattling or misalignment
• Helps maintain proper spacing for connected parts to operate correctly
• Reduces noise caused by loose fittings or vibration

• Recommended for users comfortable with appliance repair; disconnect power before servicing
• Remove adjacent panels or components as needed for access; keep fasteners organized
• Inspect mating surfaces and replace any damaged screws or clips for a secure fit

This metal angle support bracket secures appliance panels and components to the cabinet, helping maintain alignment and stability for long-lasting operation. Use it to replace a bent, cracked, or missing bracket that lets panels shift or rattle. What it does

• Provides a stable mounting point for panels, housings, or internal components
• Restores proper alignment when a corner or panel sits uneven or gaps appear
• Reduces vibration and rattling caused by loose or damaged supports
• Helps prevent further wear from components rubbing or shifting out of place

• Disconnect power to the appliance before starting any repair
• Use the existing fasteners when possible; replace stripped or damaged screws
• Verify correct orientation and alignment before fully tightening fasteners
• Take care to avoid damaging seals or wiring

This is the roller guide assembly that sits on the floor of the microwave and supports the glass turntable tray, allowing it to rotate smoothly during cooking. It typically consists of a ring with small wheels or rollers. Replace this part if the turntable wobbles, does not rotate evenly, or if the rollers are broken or worn, which can cause uneven cooking or noise during operation.

Hardware kit for mounting microwave to wall and cabinet. Includes screws, bolts, and washers for secure installation. Replaces lost or missing fasteners.

A replacement unified-thread screw used to secure appliance panels and internal components. Provides a direct fastener to restore secure attachment when original screws are missing, damaged, or corroded. What it does:

• Fastens panels, brackets, trim pieces, and other appliance components that use a unified-thread screw.
• Restores secure mounting to reduce rattling, movement, or misalignment of parts.
• Replaces stripped, rusted, or missing screws to help maintain safe operation.
• Works where the appliance's service manual or parts diagram specifies a unified-thread fastening point.

• Disconnect power and water before servicing for safety.
• Use the correct screwdriver or bit to avoid stripping the head; install by hand until started, then snug—do not overtighten.
• Replace like-for-like: match thread type and length to the removed screw to ensure proper fit and function.
• If other fasteners show corrosion or damage, inspect nearby hardware and replace as needed.

3mm x 8mm screw secures trim, panels, and brackets inside your microwave. Replace missing or stripped screws to restore proper fit and alignment.

Replacement trim frame for microwave door and control area. Restores outer appearance when original is cracked, chipped, warped, or bent. Direct-fit part.

This is a plastic bracket that holds the door interlock switches in proper alignment inside the microwave's door latch assembly. It ensures the switches are correctly positioned to detect when the door is open or closed. Replace this part if the microwave won't start, runs with the door open, or if the switch holder is cracked or broken.

This sensor detects moisture levels inside the microwave cavity during cooking and communicates with the control board to adjust cook times automatically. It is a key component for auto-cook and sensor-reheat functions. Replace this sensor if the microwave fails to properly detect doneness, overcooks or undercooks food on sensor settings, or displays a sensor error code.

If your microwave stops mid-cycle, won't heat, or keeps resetting, the control board likely failed. This board regulates power to all microwave functions.

Controls airflow in your microwave. Replaces a cracked, broken, or worn damper assembly. Installs in the ventilation system to restore proper operation.