Electrolux Microwave Parts

This replacement cam is the small pivot piece that helps a refrigerator door hinge open and close smoothly and keep the door aligned. Installing the cam restores proper hinge movement for a secure, even door fit. What it does:

• Acts as the hinge pivot point to guide door rotation and alignment
• Helps prevent door sagging, binding, or uneven gaps
• Reduces noisy or rough hinge movement caused by a worn cam
• Works with the hinge assembly to maintain proper door sealing

• One cam

• Disconnect power to the appliance or unplug before starting any work
• Support the door while removing hinge fasteners to prevent damage or injury
• Inspect mating hinge surfaces and replace any damaged hardware for best results
• Tighten hinge fasteners to manufacturer torque and check door alignment after installation

This holder is a small mounting bracket that secures internal appliance components to prevent movement and maintain proper alignment, helping reduce noise and keep parts functioning reliably. What it does:

• Secures and positions an internal component or assembly to the appliance frame
• Prevents shifting or sagging that can cause rattling or misalignment
• Helps maintain proper spacing for connected parts to operate correctly
• Reduces noise caused by loose fittings or vibration

• Recommended for users comfortable with appliance repair; disconnect power before servicing
• Remove adjacent panels or components as needed for access; keep fasteners organized
• Inspect mating surfaces and replace any damaged screws or clips for a secure fit

This metal angle support bracket secures appliance panels and components to the cabinet, helping maintain alignment and stability for long-lasting operation. Use it to replace a bent, cracked, or missing bracket that lets panels shift or rattle. What it does

• Provides a stable mounting point for panels, housings, or internal components
• Restores proper alignment when a corner or panel sits uneven or gaps appear
• Reduces vibration and rattling caused by loose or damaged supports
• Helps prevent further wear from components rubbing or shifting out of place

• Disconnect power to the appliance before starting any repair
• Use the existing fasteners when possible; replace stripped or damaged screws
• Verify correct orientation and alignment before fully tightening fasteners
• Take care to avoid damaging seals or wiring

The Door Switch is an OEM replacement part for Frigidaire wall ovens. It is a component located on the oven door that detects when the door is opened and closed. The door switch works alongside the control board to regulate oven operations based on door position.  

Symptoms of a bad door switch can include:

• Oven failing to automatically go into bake or warm modes after door closure
• Interior lights not turning on when the door is opened
• Control buttons/display remaining constantly lit instead of dimming
• Oven not heating or functioning properly in different modes

Causes relate to normal wear over extended use as the door switch mechanism cycles with frequent door openings and closings. Moisture exposure or impacts could also degrade switch performance.

This OEM Frigidaire switch is compatible with Amana, Jenn-Air, KitchenAid, and some Electrolux wall oven models as well.

Secures microwave components to cabinet or frame. Replace when bracket is broken, cracked, or worn causing misalignment or excess vibration during operation.

Hardware kit for mounting microwave to wall and cabinet. Includes screws, bolts, and washers for secure installation. Replaces lost or missing fasteners.

Secures your microwave door to engage the safety switches. Replace if the hook is cracked, broken, or worn, preventing the door from latching properly.

3mm x 8mm screw secures trim, panels, and brackets inside your microwave. Replace missing or stripped screws to restore proper fit and alignment.

This interior refrigerator lamp provides reliable lighting inside the fresh-food compartment so you can see contents clearly. It replaces a dim or non-working lamp to restore normal interior illumination. What it does:

• Provides interior lighting for the refrigerator compartment
• Replaces a burned-out, flickering, or intermittently working lamp
• Helps you find food and check expiration labels without opening the compartment longer than necessary
• Works with the existing lamp housing and socket when compatible

• One interior refrigerator lamp

• Disconnect power to the appliance before replacing the lamp to avoid electrical shock
• Allow the lamp and surrounding area to cool before handling
• Handle the lamp carefully to avoid breakage; dispose of broken bulbs per local regulations
• Check the socket and appliance light switch for faults if the lamp does not light after installation.

If your microwave stops mid-cycle, won't heat, or keeps resetting, the control board likely failed. This board regulates power to all microwave functions.

Replacement lever for microwave door or latch mechanisms. Installs to operate control arms and moving parts. Needed when original is cracked, broken, or worn.

Connects the turntable motor to the rotating glass tray in your microwave. Replace if the coupler is cracked, broken, or missing and the tray won't rotate.