Electrolux Range / Cooktop / Oven Heating Element

This is the radiant heating element that sits beneath the glass-ceramic cooktop. Replace a failed element to restore proper heat on the affected burner and ensure consistent, even cooking performance on your range. What it does:

• Converts electrical power into heat for a single surface burner under the glass cooktop
• Restores a burner that won't heat, heats weakly/unevenly, or cycles off prematurely
• Helps resolve visible hot spots, burn marks, or open breaks on the element
• Supports accurate temperature control when paired with a working switch/limiter

• 1 radiant surface element

• Disconnect power at the breaker before servicing; allow the cooktop to cool completely
• Lift/remove the glass top per your service manual to access the element
• Transfer brackets/clips and move wires one-by-one to the same terminals on the new element
• Handle carefully to avoid damaging the element or glass; verify secure connections before reassembly

The Element Surface Dual is an OEM part for Frigidaire cooktops. This dual surface element provides flexible cooking options by offering two heating zones within a single element, allowing for efficient cooking with pots and pans of various sizes.

Causes of a bad dual surface element can include wear and tear from regular use, overheating, or damage from spills and impact. A malfunctioning element can result in uneven heating or failure to heat entirely, impacting your cooking experience.

Symptoms of a bad dual surface element include:

• The element not heating up
• Inconsistent or uneven heating
• Visible damage such as burns or breaks in the element
• The element only heating on one side

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This broil heating element mounts at the top of the oven cavity to provide intense, direct heat for broiling and to assist with preheating. Replacing a failed element restores even broiling performance and helps the oven reach temperature properly.

• Provides high, top-down heat for broiling
• Common failure symptoms: no broil heat, uneven browning, trips breaker when broil is selected, visible hot spots or breaks in the element
• Helps with overall oven preheat and temperature recovery

• Disconnect power before service; the element is high-voltage
• Remove oven racks to access mounting screws
• Support wiring when transferring leads to the new element to prevent panel damage
• Avoid touching new element with bare hands; clean any oils from terminals

The Radiant Surface Element is an OEM part for Frigidaire ranges and cooktops. This part generates heat for cooking and boiling on the cooktop surface.

Causes of a bad Radiant Surface Element can range from electrical issues or loose connections to physical damage from impact or spillovers.  

Symptoms of a faulty Radiant Surface Element include:

• Element not heating up or providing insufficient heat
• Element glowing unevenly or only partially heating
• Cracks or damage visible on the element surface
• Burning smells or discoloration on the cooktop

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This replacement radiant surface element restores consistent burner heating under the glass cooktop on compatible electric ranges. It helps your cooking zone reach and maintain temperature so pots and pans heat evenly.

• Converts electrical energy into radiant heat beneath the glass surface
• Maintains set temperature by cycling on and off during operation
• Common symptoms: burner won't heat, heats weakly or unevenly, or only part of the ring glows
• May show visible scorching or breaks when inspected after access

• Disconnect power at the breaker before servicing and allow the cooktop to cool completely
• Lift/prop the glass top or remove the burner pan as your model requires to access the element
• Label and transfer wires one at a time; ensure all terminals are firmly seated
• Handle the element carefully to avoid bending or stressing the coil and supports

The Broil Heating Element is an OEM part for Frigidaire ranges. Located inside the oven compartment, it provides heat energy for the broil cooking function. 

Causes of a bad broil element can include mineral buildup over time, surface corrosion or internal wire fatigue from ongoing temperature cycling.

Symptoms of a bad broil element include:

• Inadequate or uneven broiling temperatures
• Element failing to glow red or turn on fully
• Burning or charring of foods below the element
• Oven display showing error code related to element failure

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This is the radiant surface heating element that powers one burner on a glass-ceramic cooktop. Replacing a failed element restores fast, even heat and reliable temperature control for everyday cooking.

• Converts electrical energy into heat for a single cooktop zone
• Works with the burner control to cycle on/off and maintain temperature
• Common symptoms include no heat, intermittent heat, or very slow heating
• Visible hot spots, blisters, or cracks on the element indicate failure

• Disconnect power to the range/cooktop before servicing; high voltage is present
• Allow the glass top to cool; lift or remove it to access the element as your model requires
• Transfer wires one at a time to the new element; secure using existing brackets/mounts
• Ensure the element is centered under the glass and test operation before reassembly

This bake element is the oven heating element that provides the heat for baking and roasting. Replace a damaged or failed element to restore normal bake performance and even cooking results. What it does:

• Converts electrical power into radiant heat for the oven bake cycle.
• Heats and glows when operating; failure can cause little or no bake heat.
• Common symptoms: oven won't reach set temperature, food cooks unevenly, or element shows visible breaks or heavy corrosion.
• Fits as the direct replacement heating element for the bake function when matched to your model.

• Disconnect power to the appliance at the breaker or fuse box before starting any work.
• Allow the oven to cool completely and wear gloves to protect hands from sharp edges.
• Confirm terminal orientation and secure electrical connections; ensure the element is seated and fastened per your model's instructions.

Bake element restores oven heat by producing the radiant heat needed for baking and roasting. Replacing a worn or damaged bake element helps the oven reach and maintain set temperatures for more consistent cooking results. What it does:

• Heats the oven cavity to provide direct radiant heat for baking and roasting.
• Use when the element shows visible breaks, blistering, or does not glow when the oven is set to high.
• Common symptom indicators: oven won't reach set temperature, uneven baking, or longer-than-normal cook times.
• Works as a direct replacement for the oven's lower/bake heating element.

• Disconnect power at the breaker or unplug the appliance before starting any repair.
• Allow the oven to cool completely and wear gloves to avoid sharp edges.
• Match the part to your model and terminal layout before installing; tighten connections securely.

This radiant surface element restores heat to a smooth-top cooking zone on glass-ceramic ranges. Replace a failed element to bring back consistent, controllable heat for everyday simmering, sautéing, and boiling.

• Provides radiant heat beneath the glass cooktop for one burner zone
• Typical symptoms: burner won't heat, heats only partially, or shows visible hot spots/burn marks
• Helps correct slow-to-heat or uneven cooking performance from a failed element
• Often tests open (no continuity) when the internal coil is burned out

• Disconnect power at the breaker before servicing; elements operate on high voltage
• Lift and support the glass cooktop carefully to avoid cracking the glass
• Note and transfer wires one at a time to the new element; match terminals precisely
• Ensure the element sits level in its brackets and that wires aren't pinched before reassembly

This part is a replacement surface element designed for use with various different models of ranges and electric cooktops.This part supplies the heat to the cooktop and thus is critical for proper appliance functionality. If the current surface element is worn, malfunctioning, or in any way rendered ineffective, it will need to be immediately replaced. Ensure the range is entirely disconnected from the power source before attempting to replace this part. Work gloves should be worn whenever attempting appliance repairs.This is a genuine OEM part made by Frigidaire and has been sourced directly from the manufacturer. This surface element is suitable for use on a variety of range models manufactured by Frigidaire, Electrolux, Gibson, Kelvinator, and some other brands. It is a genuine OEM part and thus is manufactured from high-quality, durable materials. This part is sold individually.

Restore reliable top heat for broiling and browning. This replacement broil heating element brings your oven's broil function back to full strength so foods brown evenly and the broiler heats when selected.

• Provides high, direct heat from the top of the oven during the broil cycle
• Helps with top-browning in some baking/roasting modes
• Common failure signs: broiler won't heat or glow, uneven browning, visible breaks or blistering on the element
• Often tests "open" (no continuity) when failed

• Disconnect power at the breaker before servicing; allow the oven to cool completely
• Remove mounting screws, then gently pull the element forward and support the wires
• Label and transfer wires to the new element one at a time; do not allow wires to slip back into the rear cavity
• Reinstall screws, ensure secure connections, restore power, and test the broil function

This oven bake element is the heating element that warms the oven cavity for baking and roasting. Replacing a damaged element restores proper oven heating and helps return cooking performance to normal. What it does:

• Heats the oven interior for baking, roasting and browning.
• Replaces elements that are visibly burnt, cracked, broken, or no longer glow when the oven is on.
• Common symptoms it can fix: little or no heat from the oven, uneven cooking, or an element that sparks or shows burn spots.
• Works as the direct heater inside the oven cavity; connects to the oven terminal block.

• Disconnect power at the breaker or unplug the appliance before starting any repair.
• Access typically requires removing the oven interior panels or rear access panel; support the element while disconnecting terminals.
• Handle terminals and sharp sheet metal carefully; use insulated tools and secure terminal connections.

This oven heating element replaces a failed bake element to restore even, reliable oven heat for baking and roasting. It's a direct-replacement style part that heats the oven cavity when the bake function is used. What it does

• Heats the oven cavity during bake cycles so food cooks evenly
• Commonly used when the oven won't reach or hold baking temperatures
• Can fail visibly (broken or burned) or electrically (open circuit)
• Works with the oven's temperature control to maintain set temperature

• Disconnect power at the breaker before starting any repair to avoid shock.
• Handle the element carefully; connectors and terminals can be fragile.
• Confirm wire terminal fit and secure mounting; replace only with the correct OEM-style element.

This replacement bake element heats the lower oven cavity so your range can bake and roast food at set temperatures. Restores normal baking performance when the oven isn't heating properly. What it does:

• Heats the oven's lower cavity to reach and maintain baking temperatures
• Replaces a burned-out, warped, or visibly damaged element
• Helps correct symptoms like no heat or uneven baking results
• Works with the oven control to provide consistent interior temperatures

• Disconnect power to the appliance before any service to avoid shock
• Handle element carefully; sharp edges and fragile terminals can be damaged
• Verify proper terminal connection and secure mounting during installation