Electrolux Range / Cooktop / Oven Parts

Oven shutting off during baking or self-clean? This limit thermostat prevents overheating and restores reliable operation. Direct replacement part.

This is a triple radiant surface element used on glass-top electric ranges. It provides heat to the cooktop surface and typically features multiple heating zones for different pot sizes. Replace this element if your cooktop burner is not heating evenly, only partially heating, or not turning on at all.

This electronic oven control board governs your range's heating functions and displays the time and timer. Replacing a failed board restores reliable bake/broil operation, accurate temperature control, and a responsive clock/timer interface. What it does:

• Controls bake/broil circuits to run selected cooking modes
• Monitors the oven temperature sensor and regulates heat to the set temperature
• Drives the time-of-day and countdown timer display
• Interprets keypad inputs for mode selection and settings
• Failure symptoms can include no heat or erratic heat, a blank or flickering display, or unresponsive buttons

• One electronic control board assembly

• Disconnect power at the breaker before servicing; verify no voltage is present
• Use anti-static precautions and handle the board by its edges
• Photograph wiring and transfer connectors one at a time to the same positions
• Reuse the existing mounting hardware and any faceplate/overlay as required; set the clock after restoring power

Fix grinding or buzzing fan noise during preheat or cool-down. This motor restores proper airflow in your oven. Moderate DIY, 30-60 minutes.

Replacement end cap that finishes and secures the open end of your microwave handle. Restores a clean appearance when the original cap is cracked or missing.

Burner not heating or heating unevenly? This surface heating element restores consistent temperature control. Common fix for cold or slow-heating burners.

Replacement power cord for ovens and ranges. Installs at the rear panel to restore electrical connection. Needed when original cord is frayed or damaged.

This switch assembly restores electrical on/off control for a specific appliance function. Replace a worn or failed switch to stop intermittent operation and return reliable control to the affected circuit. What it does:

• Provides the electrical on/off or function control for the appliance circuit.
• Replaces a failed switch that can cause intermittent operation or unresponsive controls.
• Helps resolve symptoms such as a function that won't start, no response from the control, or erratic switching.
• Connects to the existing wiring harness and mates with the original mounting points.

• Disconnect power to the appliance before beginning any work.
• Remove the appropriate access panel to reach the switch; note wire and terminal locations before disconnecting.
• Unplug the wiring harness or carefully detach terminals, swap the switch assembly, then reconnect securely.
• Restore power and verify the replaced switch operates the function correctly.

Uneven baking or convection mode not working? This rear-mounted convection fan heating element circulates hot air for consistent cooking results.

Combines spark igniter electrode with orifice holder for gas surface burners. Replace when cracked, broken, or no longer securely holding components in place.

This oven control board manages the range's bake and broil functions, temperature regulation, and the display/timer. Replacing a failed board restores accurate heating and responsive controls so the oven starts, runs, and shuts off as expected.

• Regulates bake and broil element relays based on temperature-sensor feedback and user settings
• Powers and manages the clock, timer, and oven display interface
• Common symptoms of failure: no bake/broil heat, blank or unresponsive display, beeping or error codes, oven won't turn off, or erratic temperature
• Helps restore consistent preheating and temperature control when the existing board is faulty

• Disconnect power at the breaker before servicing; verify no power is present
• Access the board from the control panel/backguard area
• Photograph wiring, then move connectors and mounting hardware to the new board one-for-one; handle electronics by the edges to avoid ESD damage
• After reassembly, restore power and test bake and broil functions and the display/keys

Low-friction slide piece that supports moving components in your range or wall oven. Replace worn or cracked glides to restore smooth operation.

This is the cooling fan motor that draws air across the oven cavity and control panel area to prevent overheating of surrounding cabinetry and electronic components. It typically runs during and after oven use to dissipate heat. Replace this motor if the oven shuts off unexpectedly due to overheating, the cooling fan does not spin, or you notice excessive heat around the control panel or cabinet surfaces near the range.

Fix an oven door that won't lock during self-clean or clean cycle errors. This door latch assembly secures the door and reports lock status to the control.

Fix display issues, unresponsive controls, or oven overheating with this electronic control board. Manages bake/broil functions and timing display.

Factory glass assembly that restores the viewing window on your range door. Replaces cracked, shattered, or missing glass panels for safe operation.