Electrolux Range Parts

This electronic oven control board governs your range's heating functions and displays the time and timer. Replacing a failed board restores reliable bake/broil operation, accurate temperature control, and a responsive clock/timer interface. What it does:

• Controls bake/broil circuits to run selected cooking modes
• Monitors the oven temperature sensor and regulates heat to the set temperature
• Drives the time-of-day and countdown timer display
• Interprets keypad inputs for mode selection and settings
• Failure symptoms can include no heat or erratic heat, a blank or flickering display, or unresponsive buttons

• One electronic control board assembly

• Disconnect power at the breaker before servicing; verify no voltage is present
• Use anti-static precautions and handle the board by its edges
• Photograph wiring and transfer connectors one at a time to the same positions
• Reuse the existing mounting hardware and any faceplate/overlay as required; set the clock after restoring power

Fix display issues, unresponsive controls, or oven overheating with this electronic control board. Manages bake/broil functions and timing display.

This oven control board manages the range's bake and broil functions, temperature regulation, and the display/timer. Replacing a failed board restores accurate heating and responsive controls so the oven starts, runs, and shuts off as expected.

• Regulates bake and broil element relays based on temperature-sensor feedback and user settings
• Powers and manages the clock, timer, and oven display interface
• Common symptoms of failure: no bake/broil heat, blank or unresponsive display, beeping or error codes, oven won't turn off, or erratic temperature
• Helps restore consistent preheating and temperature control when the existing board is faulty

• Disconnect power at the breaker before servicing; verify no power is present
• Access the board from the control panel/backguard area
• Photograph wiring, then move connectors and mounting hardware to the new board one-for-one; handle electronics by the edges to avoid ESD damage
• After reassembly, restore power and test bake and broil functions and the display/keys

This is the cooling fan motor that draws air across the oven cavity and control panel area to prevent overheating of surrounding cabinetry and electronic components. It typically runs during and after oven use to dissipate heat. Replace this motor if the oven shuts off unexpectedly due to overheating, the cooling fan does not spin, or you notice excessive heat around the control panel or cabinet surfaces near the range.

This switch assembly restores electrical on/off control for a specific appliance function. Replace a worn or failed switch to stop intermittent operation and return reliable control to the affected circuit. What it does:

• Provides the electrical on/off or function control for the appliance circuit.
• Replaces a failed switch that can cause intermittent operation or unresponsive controls.
• Helps resolve symptoms such as a function that won't start, no response from the control, or erratic switching.
• Connects to the existing wiring harness and mates with the original mounting points.

• Disconnect power to the appliance before beginning any work.
• Remove the appropriate access panel to reach the switch; note wire and terminal locations before disconnecting.
• Unplug the wiring harness or carefully detach terminals, swap the switch assembly, then reconnect securely.
• Restore power and verify the replaced switch operates the function correctly.

For 12k burner.

Low-friction slide piece that supports moving components in your range or wall oven. Replace worn or cracked glides to restore smooth operation.

Replacement control knob for your range. Attaches to the control shaft to operate burners or oven functions. Replace if cracked, broken, or missing.

Fix an oven door that won't lock during self-clean or clean cycle errors. This door latch assembly secures the door and reports lock status to the control.

Replaces cracked or corroded sealed burner head on gas ranges and cooktops. Restores proper flame distribution when original part is damaged or clogged.

Combines spark igniter electrode with orifice holder for gas surface burners. Replace when cracked, broken, or no longer securely holding components in place.

Convection fan motor that circulates hot air inside the oven cavity for even cooking temperatures. Replace if fan stops spinning or makes excessive noise during convection baking.

Replacement handle for range oven doors. Installs on the front door panel for gripping and opening. Needed when original handle is cracked or broken.

Fix E15 errors, runaway oven temperature, or unresponsive controls with this range control board. Manages cooking modes and temperature regulation.

Replace a cracked, broken, or missing oven door spacer that maintains proper alignment and gap between door components. Installs in door assembly.

Fix oven lights that won't turn off, error codes E75/E35/F15, or non-responsive controls. This control board restores normal range operation.