Electrolux Range Heating Element

Burner won't heat or heats unevenly? Replace the radiant surface element beneath your glass cooktop. Restores proper heat output for consistent cooking.

Dual element not heating or only outer ring works? This cooktop surface element fits both heating zones. DIY repair typically takes 15-30 minutes.

Oven won't broil or preheat properly? This broil element provides intense top-down heat. DIY-friendly repair restores even broiling in 30-45 minutes.

Burner won't heat evenly or only outer ring works? This dual 9/12 inch radiant surface element restores proper heating. Easy DIY replacement in minutes.

Broiler not heating or working? This broil element restores high-heat cooking. Easy DIY fix with four screws and wire connectors. Takes about 30 minutes.

This replacement radiant surface element restores consistent burner heating under the glass cooktop on compatible electric ranges. It helps your cooking zone reach and maintain temperature so pots and pans heat evenly.

• Converts electrical energy into radiant heat beneath the glass surface
• Maintains set temperature by cycling on and off during operation
• Common symptoms: burner won't heat, heats weakly or unevenly, or only part of the ring glows
• May show visible scorching or breaks when inspected after access

• Disconnect power at the breaker before servicing and allow the cooktop to cool completely
• Lift/prop the glass top or remove the burner pan as your model requires to access the element
• Label and transfer wires one at a time; ensure all terminals are firmly seated
• Handle the element carefully to avoid bending or stressing the coil and supports

Oven not heating or baking unevenly? This hidden bake element restores proper bottom heat. Moderate DIY repair—requires removing oven racks and panels.

Burner won't heat or gets no power? This surface element supplies heat to your cooktop. Easy DIY fix—test for power at terminals first.

Food won't brown or broiler not heating? This broil element restores high, direct heat from the top of your oven. DIY-friendly, takes about 10 minutes.

This oven bake element is the heating element that warms the oven cavity for baking and roasting. Replacing a damaged element restores proper oven heating and helps return cooking performance to normal. What it does:

• Heats the oven interior for baking, roasting and browning.
• Replaces elements that are visibly burnt, cracked, broken, or no longer glow when the oven is on.
• Common symptoms it can fix: little or no heat from the oven, uneven cooking, or an element that sparks or shows burn spots.
• Works as the direct heater inside the oven cavity; connects to the oven terminal block.

• Disconnect power at the breaker or unplug the appliance before starting any repair.
• Access typically requires removing the oven interior panels or rear access panel; support the element while disconnecting terminals.
• Handle terminals and sharp sheet metal carefully; use insulated tools and secure terminal connections.

Burner won't heat or randomly stays on? This range heating element restores proper burner function. DIY repair takes about 30 minutes with basic tools.

Burner not heating or heating unevenly? This surface heating element restores consistent temperature control. Common fix for cold or slow-heating burners.

Fix a burner that won't heat with this range surface element. This electromagnetic coil transfers energy to heat cookware. Direct replacement part.

This bake element is the oven's main heating element that provides consistent heat for baking and roasting. Replacing a failed element restores proper oven temperature and cooking performance. What it does:

• Heats the lower oven cavity for baking and roasting cycles.
• Common symptom: oven does not heat or reaches lower-than-set temperatures.
• Common symptom: uneven baking or food undercooks on all racks.
• Also check for visible damage, burn marks, or broken connectors.

• Disconnect power at the breaker or unplug the appliance before starting any repair.
• Allow the oven to cool fully before accessing the interior; wear gloves to protect against sharp edges.
• Remove the oven cavity access panel or back panel as required to access element mounting screws and wiring.
• Verify wiring connections are secure and test the element for continuity with a multimeter before final reassembly.