Electrolux Refrigerator Hose Or Tube

This replacement tube carries water from the inlet valve into the refrigerator's icemaker. An intact fill tube helps route water cleanly to the mold, reducing leaks, drips, and ice build-up around the fill area.

• Directs water into the icemaker fill cup/mold during the fill cycle
• Helps seal the cabinet pass-through to prevent leaks and frost intrusion
• Replaces tubes that are cracked, kinked, or blocked by ice/mineral deposits
• Symptoms may include no ice or small cubes, water dripping/ice sheet in the freezer, or frost near the fill tube

• Unplug the refrigerator and shut off the water supply before servicing
• Remove the icemaker as needed, clear any ice from the fill opening, and pull the old tube from the cabinet port
• Insert the new tube fully, align it with the icemaker fill cup, and reconnect the water line
• Restore water and power, then check for proper fill and leaks

This replacement tube routes water inside the refrigerator to the dispenser or ice maker, restoring proper water flow and preventing leaks when the original tubing is cracked or worn. Simple direct-fit replacement when the OEM tubing fails. What it does:

• Carries water between the refrigerator supply and the dispenser or ice maker
• Replaces cracked, split or collapsed tubing that can cause leaks
• Helps restore steady water flow and proper ice-making or dispensing
• Prevents water damage from deteriorated or pinched lines

• Designed for refrigerator models that use this exact OEM tube
• Disconnect power and shut off the water supply before replacing tubing
• Inspect connections and seals; replace any damaged clips or fittings to ensure a watertight seal

This water inlet tube routes household water from the supply to the fridge's internal water system, helping deliver water to the dispenser and ice maker without leaks. Durable tubing replaces cracked or kinked lines to restore proper flow. What it does:

• Directs water from the supply valve to the refrigerator's internal water components.
• Replaces cracked, split, or kinked tubing that can cause leaks or low flow.
• Helps restore water flow to the dispenser and ice maker when the original line is damaged.
• Provides a secure, leak-resistant path when installed with proper fittings or clamps.

• One water inlet tube.

• Always disconnect power and shut off the water supply before replacing the tube.
• Drain and relieve pressure from the water line before disconnecting fittings to avoid spills.
• Use the correct OEM clamps or fittings and inspect connectors for wear; replace clamps if damaged.
• Tighten fittings securely but avoid over-tightening plastic fittings to prevent cracking.

This water inlet tube routes incoming water from the supply to the refrigerator's internal water system, restoring proper flow for the dispenser and icemaker. Replace a damaged tube to stop leaks and regain reliable water delivery. What it does

• Channels water from the household supply to the fridge's water valve, dispenser, and icemaker
• Helps prevent leaks caused by cracked, pinched, or deteriorated tubing
• Can restore water flow when internal tubing is blocked or split
• Works with the appliance's existing fittings and seals when installed correctly

• One water inlet tube

• Disconnect power and shut off the water supply before beginning work
• Inspect and reuse only original fittings and seals if undamaged; replace seals if leaking
• Avoid sharp bends or kinks when routing the tube; secure with existing clips or brackets

This replacement tubing routes water between components inside your appliance. It restores reliable, leak-resistant water flow when the original line becomes brittle, kinked, or damaged, helping dispensers and ice systems work properly on applicable models.

• Transports water between the inlet valve and internal components
• Replaces tubing that is cracked, brittle, kinked, or leaking
• Helps address issues like leaks, reduced dispenser flow, or ice maker fill problems on applicable units
• Maintains proper water flow and pressure within the line

• Disconnect power and shut off the water supply before servicing
• Place a towel or tray to catch residual water and relieve line pressure
• Note the original routing; transfer any retainers or clips from the old line; ensure connections are fully seated and ends are cut square if trimming is required
• Restore water and power, then check all connections carefully for leaks

This water inlet tube supplies water from the refrigerator's supply to the dispenser and ice maker, restoring proper flow and preventing routing issues. It's a direct-fit replacement that helps stop leaks and restore water delivery. What it does:

• Directs water from the house supply to the refrigerator's internal water system.
• Restores water flow to the dispenser and ice maker when a damaged tube is blocking supply.
• Prevents leaks and water pooling caused by cracked, pinched, or corroded inlet tubing.
• Works with other inlet fittings and valves to maintain proper water routing.

• Shut off the refrigerator power and water supply before starting any work.
• Remove access panels as needed and relieve any residual water pressure in the line.
• Use proper tubing connectors and tighten fittings to manufacturer torque—inspect for leaks after restoring water.
• If you find additional damaged fittings or clamps, replace them to ensure a leak-free install.