Electrolux Refrigerator Parts

This condenser coil assembly removes heat from the refrigerant so your refrigerator can cool properly. Replacing a damaged or clogged condenser helps restore cooling performance and can improve compressor efficiency. What it does:

• Transfers heat from the refrigerant to the surrounding air so the cooling cycle can continue
• Helps maintain proper compressor operating temperatures and system pressure
• Commonly addresses symptoms like reduced cooling, prolonged run cycles, or warm cabinet temperatures
• Works with the refrigerator's fan and compressor as part of the sealed refrigerant loop

• Always unplug the appliance before attempting service
• Access may require removing the rear cover or lower kickplate; follow the manufacturer's disassembly instructions
• Handle the coil gently to avoid bending fins or damaging connections

This filter release button is the push-button used to release and remove the refrigerator water filter housing. It restores simple, one-handed filter removal so you can replace your water filter cleanly and quickly. What it does:

• Replaces a damaged or worn filter-release push button that no longer unlatches the filter housing
• Allows the filter cartridge to be released from the housing for regular replacement
• Helps resolve symptoms like a stuck, loose, or non-responsive filter release mechanism
• Fits into the filter housing assembly and engages the release latch when pressed

• Disconnect power and shut off the water supply before servicing the filter area
• Remove any trim or access panels per your refrigerator manual to access the button
• Snap or fasten the new button into the housing until it engages; avoid forcing parts

This air duct gasket seals the refrigerator's air duct to help direct cold airflow and reduce air leaks for more consistent temperatures. It replaces a worn or damaged duct seal to restore proper circulation and efficiency. What it does:

• Seals the connection between the air duct and cabinet to prevent cold air loss
• Helps maintain consistent fridge/freezer temperatures by directing airflow
• Reduces frost buildup and uneven cooling caused by gaps or leaks
• Commonly replaced when torn, compressed, or missing

• Designed for straightforward replacement; inspect surrounding duct for damage before installing
• Clean mating surfaces and remove old adhesive or residue for a proper seal
• Use appropriate hand tools; avoid sharp tools that could cut the gasket
• Disconnect power to the appliance if accessing electrical components nearby

This genuine replacement screw secures panels and small components on select appliances, restoring fit and reducing rattles or loose parts. It's a direct-fit fastener where the original #8-18 x 3/8 screw is missing or worn. What it does:

• Fastens trim, panels or brackets to appliance frames and components
• Restores secure fit to stop rattling or misaligned parts
• Replaces stripped, rusted or missing screws that prevent proper assembly
• Matches original thread size and length for correct engagement

• Use the correct driver and engage threads straight to avoid stripping
• Do not overtighten; stop when the part is snug and secure
• Replace any damaged mating hardware for best fit
• Unplug the appliance or shut off power when accessing internal fasteners

This plug seals an unused hole in an appliance cabinet or inner liner to help block drafts, pests and moisture. It restores a clean, finished appearance and prevents accidental debris entry where a fitting or fastener is not used. What it does:

• Seals unused openings in the appliance cabinet or liner to keep out dust, moisture and pests
• Helps prevent air leaks that can affect temperature stability in refrigerators and freezers
• Covers exposed holes left after removing or relocating components or fasteners
• Restores a finished look to access areas and reduces risk of small-item ingress

• One cabinet sealing plug

• Push the plug into the hole until fully seated; no special tools usually required
• Turn off and unplug the appliance before reaching into compartments or behind panels
• Inspect the hole and plug for correct fit; replace if cracked or deformed

This self-close assembly helps the appliance door latch and finish closing smoothly, reducing door slams and improving seal reliability. It replaces a worn or broken hinge cam that prevents proper self-closing action. What it does:

• Acts as the self-closing cam/hinge component that catches and guides the door during the final closing motion
• Restores consistent, controlled door closing when worn parts cause the door to stay ajar or not latch fully
• Helps improve door seal engagement by ensuring the door closes completely
• Commonly replaced when the door feels loose, binds, or fails to self-close

• One self-close assembly

• Requires removal of the door hinge/trim; for exact steps
• Handle carefully to avoid pinching; support the door during removal and installation
• Use appropriate hand tools; do not force parts—inspect adjacent hinge components for wear
• Disconnect power only if instructed for your model

This control/switch board receives user input and routes electrical signals to the appliance, restoring responsive controls and allowing circuits to operate as intended. Replace a failed switch board to regain reliable control panel function. What it does:

• Routes user button/knob inputs to the appliance control circuitry
• Sends power/control signals to switches, relays, or heating elements
• Works with the appliance's wiring harness and mounting points to fit into the control area

• Disconnect power at the breaker or unplug the appliance before starting
• Handle the board carefully and avoid touching contacts; observe basic ESD precautions
• Verify connector orientation and secure all wiring; do not force connectors

This door handle assembly provides a ready-to-install replacement to restore a secure, easy-grip opening for your refrigerator door. Durable construction replaces a worn or broken handle for reliable daily use. What it does:

• Replaces a cracked, loose, or broken refrigerator door handle to restore safe operation and appearance
• Provides a solid grip for opening and closing the door smoothly
• Matches factory mounting points for proper fit and alignment
• Helps prevent door damage and keeps the seal functioning by ensuring correct door movement

• Disconnect power to the appliance before beginning any repair to avoid injury
• Remove any trim or access panels as needed to access mounting screws; retain fasteners for reassembly
• Hand-tighten screws, then snug—do not overtighten to avoid cracking the handle or trim

This compressor grommet is a rubber mounting isolator that cushions and secures the compressor to the appliance chassis, helping reduce vibration and noise while preventing metal-to-metal contact and premature wear. What it does:

• Cushions compressor movement to reduce vibration transmitted to the cabinet
• Dampens noise and rattling caused by compressor operation
• Prevents direct metal-to-metal contact that can wear mounting points
• Helps keep the compressor positioned and secured under load

• Disconnect power to the appliance before accessing the compressor or base pan
• Replace grommets while supporting the compressor to avoid strain on lines and connections
• Inspect remaining mounting grommets; replace all worn isolators for best performance

This genuine appliance screw secures panels and components to keep your refrigerator parts aligned and stable. A small but essential fastener, it restores proper fit and stops rattling or loose trim for reliable operation. What it does:

• Fastens panels, trim, or internal components to the appliance frame
• Restores secure fit when factory screws are missing or stripped
• Stops vibration- or temperature-related rattling caused by loose hardware
• Helps maintain proper spacing and alignment of serviceable parts

• Turn off and unplug the appliance before servicing electrical or internal areas
• Use the matching screw hole and thread engagement; start by hand to avoid cross-threading
• Tighten until snug—do not overtighten to prevent stripping or cracking surrounding material