Estate Refrigerator Parts

White.

This door shelf trim (retainer bar) snaps across the front of a refrigerator door bin to keep bottles and condiments secure. Replace a cracked or missing rail to restore safe storage and prevent items from falling when the door opens.

• Secures items on the door shelf/bin and helps prevent spills during normal use
• Replaces broken, cracked, warped, or missing trim that won't stay attached
• Helps the door close without interference from loose items
• Typical symptoms: items fall from the door bin; rail is loose, damaged, or missing

• Empty the door bin before servicing
• Release the old trim by disengaging the end tabs or clips; pull outward to remove
• Align the new trim with the bin slots and snap both ends in evenly—do not overflex
• Inspect the door bin for cracks or worn slots that could prevent a secure fit

Used to prevent over ice production in the ice dispensing bucket.

Rod retainer clip secures a support rod or shaft to keep moving parts aligned and stable during operation. Replacing a worn or broken clip prevents rattling, binding, or components falling out and helps restore proper mechanical function. What it does:

• Holds a support rod or shaft in place to maintain alignment of moving components.
• Prevents rods from sliding out or shifting, which can cause rattling, binding, or misalignment.
• Replace if the clip is bent, cracked, corroded, or no longer grips the rod securely.
• Common symptom: loose or misaligned parts, unusual noises, or components that detach during use.

• Disconnect power (unplug or shut off breaker) before servicing the appliance.
• Access may require removing panels, covers, or nearby components—follow the OEM service manual.
• Remove the old clip and carefully press or snap the replacement into place; avoid over-bending the clip.

This replacement screw secures panels, trim pieces and small assemblies so covers and components stay aligned and rattle-free. It's a simple, direct fastening part used when an original screw is missing or damaged. What it does:

• Fastens panels, trim, control housings and other small components to the appliance chassis
• Replaces missing, worn or stripped screws that cause loose panels or rattling noises
• Restores correct alignment of covers and trims after service or disassembly
• Provides a direct, hardware-level repair instead of temporary fixes

• Disconnect power (and gas, where applicable) and ensure the appliance is cool before starting.
• Use the correct screwdriver bit and turn until snug; do not overtighten to avoid stripping threads or damaging parts.
• Keep removed hardware for reference; replace like-for-like if threads or inserts are damaged.
• Wear eye protection and gloves when working on appliances.

This replacement door handle restores a secure, comfortable grip for opening and closing your refrigerator or freezer door. It replaces a cracked, broken, or loose handle to improve safety and daily use. What it does:

• Provides a sturdy grip for opening and closing the appliance door
• Replaces cracked, broken, or loose handles that can catch or pinch
• Helps prevent further damage to door trim from continued use of a damaged handle
• Restores normal operation and appearance to the appliance front

• Disconnect power to the appliance or unplug before starting any work to avoid injury
• Remove any food and clear workspace around the door for easier access
• Minor disassembly of the door trim or end cap may be required; retain all fasteners
• Follow the manufacturer's instructions for correct torque and alignment

This wire harness routes power and signals between the appliance's controls and components to restore electrical connections and reliable operation. It replaces damaged or frayed wiring that can cause intermittent function or no power to circuits. What it does:

• Connects control board, switches, and components so signals and power transfer correctly
• Replaces broken, burned, or corroded wiring that can cause intermittent operation or component failure
• Restores proper routing and secure connections to reduce short circuits and poor contact
• Helps resolve symptoms such as non-responsive controls, no power to parts, or erratic operation

• Disconnect power (unplug appliance or shut off breaker) before starting any work
• Observe proper wire routing and secure all retaining clips and connectors to prevent rubbing or pinching
• Match connector shapes and colors; do not force connections or modify wires

This refrigerator door hinge secures and guides a fridge door for smooth opening and reliable alignment. It restores proper door movement and helps maintain an effective seal to keep temperatures stable. What it does:

• Provides the pivot point that lets the refrigerator door open and close smoothly
• Keeps the door aligned to prevent rubbing, gaps, or uneven sealing
• Helps stop drafts that can cause temperature fluctuations or higher energy use
• Suitable when a bent, broken, or worn hinge causes noisy or misaligned doors

• One door hinge

• Disconnect power and empty the door before starting; follow manufacturer's service manual for safe removal
• Typical install requires removing door trim or shelves to access hinge fasteners
• Re-tighten mounting screws securely and check door alignment; adjust per OEM instructions

Color: Black

This motor overload protector helps prevent the dryer motor from overheating by cutting power when excessive current or heat is detected. It restores normal operation when the motor cools or the overload is replaced. What it does:

• Protects the dryer motor from damage by interrupting power during overheating or overcurrent conditions
• Commonly used when the dryer motor won't start, hums but doesn't run, or the motor trips repeatedly
• Works with the motor start system to reduce the risk of burned windings and costly motor failure
• Resets or is replaced to restore normal motor operation after an overload event

• Always unplug the appliance before checking or replacing this part
• Inspect wiring and motor for underlying issues that can cause repeated overloads

This is a flat plain washer used to distribute load and space hardware on appliance assemblies. It helps keep bolts and screws seated and reduces wear on mating surfaces for more secure fastener connections. What it does:

• Provides a flat bearing surface to spread clamp load and protect parts from fastener damage
• Maintains proper spacing and alignment for mounted components
• Helps prevent fastener loosening from vibration when used with the correct bolt or screw
• Commonly used on chassis, suspension, and bracket connections

• One plain flat washer

• Disconnect power and water supply before servicing the appliance
• Replace only with the same washer size and thickness as the original for proper fit
• Tighten fasteners to secure but avoid over-torquing which can deform the washer

Bottle with brush. Color: Harvest Gold. It's 0.6 fluid ounces.

This hole cover seals an access/opening in the refrigerator evaporator housing to help maintain proper airflow and prevent moisture or frost from entering the cabinet. A simple replacement that restores the evaporator enclosure's intended seal. What it does:

• Seals an opening in the evaporator housing to reduce air leaks and unwanted moisture entry
• Helps prevent excessive frost or ice buildup near the evaporator area
• Supports consistent cooling by keeping the evaporator cover intact
• Can stop interior water or debris from entering the evaporator cavity

• Disconnect power to the appliance before starting any repair
• Remove the evaporator cover or access panel as required to reach the opening
• Press or snap the cover into place until it seats securely; no special tools typically required
• If the cover is brittle or damaged, inspect surrounding mounting surfaces and replace as needed