Parts for Ge CZS22MP2NJS1: Freezer Door Parts

Replacement mounting screw for refrigerator panels, brackets, and internal components. Secures loose assemblies when original fasteners are stripped or missing.

Replace your broken or missing refrigerator clinch rivet. This small fastener securely attaches internal components and panels in your side-by-side unit.

Replacement fastener for refrigerator door handles. Secures handle to door with durable metal construction. Needed when original is cracked or broken.

Black freezer door stop for side-by-side refrigerators. Secures the door in place when opened. Replace if cracked, broken, or missing.

Seals freezer door to prevent warm air entry and cold air loss. Replace if torn, cracked, or causing frost buildup. Confirm fit with your model number.

Replaces a broken or worn freezer door cam closure on side-by-side refrigerators. Installs on the door to control opening range and secure latching.

Ice won't dispense or dispenser flap sticks open? The ice dispenser solenoid controls ice flow. DIY-friendly repair with our install video.

The recess door retainer secures the dispenser's ice chute flapper in the refrigerator door. Replacing a cracked or missing retainer restores proper flapper pivot and sealing to help reduce frost buildup and air leaks around the dispenser.

• Holds the recess/ice door on its pivot within the dispenser assembly
• Helps the flapper close fully to seal the ice chute
• Restores smooth open/close action of the dispenser door
• Common symptoms: loose or fallen flapper, poor chute seal, frost or condensation in the dispenser area, and ice clumping near the chute

• Unplug the refrigerator before servicing the dispenser
• Carefully remove the dispenser bezel/control panel to access the ice chute door assembly
• Note spring orientation and retainer position; transfer components to the new retainer
• Verify flapper movement and seal before reassembly and restoring power

If your dispenser light stays off or won't turn on, this control board restores proper illumination. Moderate DIY, requires clip release and wiring.

Golden-gray shield that covers the dispenser opening on your refrigerator. Replace this trim piece if it's cracked, faded, or missing to restore appearance.

Ice dispenser door assembly seals the ice chute opening on your refrigerator. Replace if cracked, warped, or the rubber gasket is damaged and leaking air.

Spring that provides closing tension for the refrigerator water/ice dispenser door flap. Keeps the dispenser sealed when not in use. Replace if door hangs open or won't close.

Replacement dispenser door recess crank for refrigerators. Operates the ice/water dispenser door mechanism. Replace if broken, worn, or corroded.

Guides ice from your refrigerator door chute into your glass. Replace if cracked, broken, or missing to prevent stray ice and keep the dispenser tidy.

Water won't shut off from your refrigerator dispenser? This paddle assembly controls water flow and often fails due to switch wear or freeze damage.

Water or ice dispenser not working? This dispenser switch activates when you press the lever. Easy DIY repair—takes about 30 minutes with basic tools.

Spring that controls dispenser arm movement in refrigerators. Installs on the paddle assembly. Replace if broken, detached, or missing to restore arm function.

Connects water supply tubing sections in your refrigerator. Replace this plastic compression union if it's cracked, leaking, or broken. Installs inline.

This set screw secures refrigerator components—most commonly door handles—to their mounting studs. Replacing a missing or stripped screw restores a solid, secure feel and helps prevent loose or wobbly handles.

• Locks the handle to its mounting stud to keep it tight and secure
• Helps resolve a loose, wobbly, sliding, or rattling handle
• Replaces a missing, rounded, or damaged set screw
• Helps maintain proper handle alignment and consistent door operation

• Unplug the appliance or switch off power before servicing
• Ensure the handle is fully seated on the studs before tightening
• Start the screw by hand to avoid cross-threading; then tighten until snug
• Do not overtighten to prevent stripping the screw or handle threads

Set screw for refrigerators. Secures components in place throughout your appliance. Replace if stripped, missing, or damaged during repair work.

This module shelf supports and secures the freezer control module or related electronics, keeping components stable and properly positioned for reliable operation. Fits into the freezer compartment to help prevent vibration and contact damage. What it does:

• Provides a stable mounting surface for the freezer control module or electronics assembly
• Keeps wiring and small components organized and away from cold airflow
• Reduces vibration and movement that can cause intermittent electrical issues
• Helps prevent physical damage from loose parts inside the freezer compartment

• One module shelf

• Disconnect power to the appliance before servicing to avoid shock or injury
• Inspect and reuse existing mounting hardware if not explicitly supplied

This is a mounting screw used to secure various internal or external components in the refrigerator. It is a small Phillips pan-head fastener designed for use with the specific thread and length required by the appliance. Replace this screw if the original is stripped, lost, or damaged during a repair, causing a component to be loose or improperly secured.

Wire harness for refrigerator dispenser recess area. Replaces damaged, frayed, or corroded wiring. Essential for maintaining electrical connections.

Plastic bushing that fits inside the lower freezer door hinge assembly. Replace when cracked, worn, or broken to restore smooth door operation.

Replacement mounting screw for refrigerator panels, brackets, door handles, and trim. Needed when original hardware is missing, stripped, or corroded.

Refrigerator door hinge bushing provides smooth bearing surface for hinge pin. Replace if door sags, sticks, or misaligns. Confirm fit with your model.

Covers the recessed grille opening on your refrigerator to restore the factory appearance. Replace if cracked, broken, or missing for a clean finish.