Parts for Ge PSC25PSTBSS: 01 - Freezer Door Parts

Replace your refrigerator water filter every 6 months to maintain clean water and ice. Removes contaminants for fresh taste. Easy DIY install in minutes.

Replacement mounting screw for refrigerator panels, brackets, and internal components. Secures loose assemblies when original fasteners are stripped or missing.

Set screw secures refrigerator door handles in place. Replace if lost, stripped, or missing after repairs. Requires hex wrench for installation.

Stainless steel fastener that secures your refrigerator door handle to the door assembly. Replace when original is stripped, missing, or damaged.

Replaces broken or cracked refrigerator door stop. Installs on door to limit swing range and prevent cabinet damage. Needed when missing or worn.

This door gasket seals the refrigerator/freezer compartment to keep cold air inside and help maintain consistent temperatures. A tight seal reduces frost buildup and lowers energy use while helping food stay fresher. What it does

• Forms an airtight seal around the door to prevent warm air from entering
• Helps maintain proper internal temperature and reduce compressor run time
• Reduces frost and ice buildup by keeping humidity out of the compartment
• Common symptoms of a failing gasket: visible gaps, cold air leaks, increased frost, or higher energy bills

• Clean the door frame and gasket channel before installation for a secure fit
• Warm the gasket slightly to aid installation if needed; avoid overstretching
• Unplug the appliance or disconnect power before working on the door for safety

Replaces a broken or worn freezer door cam closure on side-by-side refrigerators. Installs on the door to control opening range and secure latching.

Guides ice from the ice maker to the dispenser or storage bin. Replace if cracked, broken, or missing to prevent ice jams and ensure proper alignment.

Stainless steel screw secures refrigerator panels, brackets, and trim. Replace missing, stripped, or corroded fasteners for stable assembly.

Replace your refrigerator's dispenser drip tray if it's cracked, peeling, discolored, corroded, or worn. Slides into place beneath the water/ice dispenser.

Ice won't dispense or dispenser flap sticks open? The ice dispenser solenoid controls ice flow. DIY-friendly repair with our install video.

The recess door retainer secures the dispenser's ice chute flapper in the refrigerator door. Replacing a cracked or missing retainer restores proper flapper pivot and sealing to help reduce frost buildup and air leaks around the dispenser.

• Holds the recess/ice door on its pivot within the dispenser assembly
• Helps the flapper close fully to seal the ice chute
• Restores smooth open/close action of the dispenser door
• Common symptoms: loose or fallen flapper, poor chute seal, frost or condensation in the dispenser area, and ice clumping near the chute

• Unplug the refrigerator before servicing the dispenser
• Carefully remove the dispenser bezel/control panel to access the ice chute door assembly
• Note spring orientation and retainer position; transfer components to the new retainer
• Verify flapper movement and seal before reassembly and restoring power

If your dispenser light stays off or won't turn on, this control board restores proper illumination. Moderate DIY, requires clip release and wiring.

Outer stainless trim piece that fits around the refrigerator dispenser. Replace if cracked, dented, or worn to restore the finished appearance.

Ice dispenser door assembly seals the ice chute opening on your refrigerator. Replace if cracked, warped, or the rubber gasket is damaged and leaking air.

Spring that provides closing tension for the refrigerator water/ice dispenser door flap. Keeps the dispenser sealed when not in use. Replace if door hangs open or won't close.

Replacement dispenser door recess crank for refrigerators. Operates the ice/water dispenser door mechanism. Replace if broken, worn, or corroded.

Replaces a cracked, broken, or worn ice chute funnel in your refrigerator door dispenser. Directs ice from the auger to your glass or container.

Water or ice dispenser not working? This dispenser switch activates when you press the lever. Easy DIY repair—takes about 30 minutes with basic tools.

Spring that controls dispenser arm movement in refrigerators. Installs on the paddle assembly. Replace if broken, detached, or missing to restore arm function.

Connects water supply tubing sections in your refrigerator. Replace this plastic compression union if it's cracked, leaking, or broken. Installs inline.

Freezer module support bracket for refrigerators. Installs inside the freezer to hold shelving or storage components. Replace if cracked or broken.

Fixed shelf that secures the freezer control module assembly in place. Replace if cracked, broken, or missing to properly mount electronics and components.

Replace your refrigerator's damaged or missing wire tilt-out basket. This door-mounted storage bin restores organization and accessibility for smaller items.

Plastic bushing that fits inside the lower freezer door hinge assembly. Replace when cracked, worn, or broken to restore smooth door operation.

Replacement mounting screw for refrigerator panels, brackets, door handles, and trim. Needed when original hardware is missing, stripped, or corroded.

Bushing that lines the upper hinge pin on refrigerator doors. Replace if cracked, worn, or missing to restore smooth door swing and proper alignment.