Parts for Ge GSHS9NGYDCSS: Freezer Door Parts

Replace your refrigerator water filter every 6 months to maintain clean water and ice. Removes contaminants for fresh taste. Easy DIY install in minutes.

Replacement mounting screw for refrigerator panels, brackets, and internal components. Secures loose assemblies when original fasteners are stripped or missing.

Set screw secures refrigerator door handles in place. Replace if lost, stripped, or missing after repairs. Requires hex wrench for installation.

Replaces worn, cracked, or missing tubular door handle on your side-by-side refrigerator. Restores easy door access and appliance appearance.

Secures the refrigerator handle to the door. Replace this fastener if it's missing, stripped, or damaged to eliminate handle wobble and restore alignment.

Stops refrigerator door from opening past 90 degrees. Mounts at base of door with screws. Replace if cracked, broken, or bent to prevent door overswing.

Seals freezer door to prevent warm air entry and cold air loss. Replace if torn, cracked, or causing frost buildup. Confirm fit with your model number.

Replaces a broken or worn freezer door cam closure on side-by-side refrigerators. Installs on the door to control opening range and secure latching.

This electronic freezer upper module controls functions for the freezer compartment, restoring proper control of temperature and related components when the original module fails. It replaces a faulty upper freezer control to help the freezer run correctly. What it does:

• Manages freezer control signals to temperature sensors, fans, and compressor circuits
• Can resolve intermittent cooling, failure-to-start, or erratic freezer behavior tied to control faults
• Stops error codes or display issues caused by a defective upper module
• Works as the direct replacement for the failed upper freezer control board

• One upper freezer electronic module

• Intended for direct replacement of the matching upper freezer control;
• Disconnect power to the appliance before starting; electrical shock hazard
• Handle the module by edges and avoid touching contacts to prevent ESD damage

Replacement ice chute door guide for your refrigerator. Installs inside the dispenser area to direct ice properly. Replace if cracked or broken.

Replacement mounting screw for refrigerator installation. Used to secure components and panels. Replace if lost, stripped, or damaged during service.

Recess grill that installs below the dispenser bar to catch spills and overflow. Replace if cracked, warped, or missing from prolonged water exposure.

Ice won't dispense or dispenser flap sticks open? The ice dispenser solenoid controls ice flow. DIY-friendly repair with our install video.

The recess door retainer secures the dispenser's ice chute flapper in the refrigerator door. Replacing a cracked or missing retainer restores proper flapper pivot and sealing to help reduce frost buildup and air leaks around the dispenser.

• Holds the recess/ice door on its pivot within the dispenser assembly
• Helps the flapper close fully to seal the ice chute
• Restores smooth open/close action of the dispenser door
• Common symptoms: loose or fallen flapper, poor chute seal, frost or condensation in the dispenser area, and ice clumping near the chute

• Unplug the refrigerator before servicing the dispenser
• Carefully remove the dispenser bezel/control panel to access the ice chute door assembly
• Note spring orientation and retainer position; transfer components to the new retainer
• Verify flapper movement and seal before reassembly and restoring power

If your dispenser light stays off or won't turn on, this control board restores proper illumination. Moderate DIY, requires clip release and wiring.

Golden-gray shield that covers the dispenser opening on your refrigerator. Replace this trim piece if it's cracked, faded, or missing to restore appearance.

Ice dispenser door assembly seals the ice chute opening on your refrigerator. Replace if cracked, warped, or the rubber gasket is damaged and leaking air.

Spring that provides closing tension for the refrigerator water/ice dispenser door flap. Keeps the dispenser sealed when not in use. Replace if door hangs open or won't close.

Replacement dispenser door recess crank for refrigerators. Operates the ice/water dispenser door mechanism. Replace if broken, worn, or corroded.

Replaces a cracked, broken, or worn ice chute funnel in your refrigerator door dispenser. Directs ice from the auger to your glass or container.

Water or ice dispenser not working? This dispenser switch activates when you press the lever. Easy DIY repair—takes about 30 minutes with basic tools.

Spring that controls dispenser arm movement in refrigerators. Installs on the paddle assembly. Replace if broken, detached, or missing to restore arm function.

Connects water supply tubing sections in your refrigerator. Replace this plastic compression union if it's cracked, leaking, or broken. Installs inline.

Fix an unresponsive dispenser control panel with this refrigerator touchpad interface assembly. Restores water and ice dispensing functionality.

Replace your broken or cracked freezer door shelf module. This storage bin installs on the inside of your refrigerator freezer door to hold items.

Wire harness for refrigerator dispenser recess area. Replaces damaged, frayed, or corroded wiring. Essential for maintaining electrical connections.

Plastic bushing that fits inside the lower freezer door hinge assembly. Replace when cracked, worn, or broken to restore smooth door operation.

Replacement mounting screw for refrigerator panels, brackets, door handles, and trim. Needed when original hardware is missing, stripped, or corroded.

Bushing that lines the upper hinge pin on refrigerator doors. Replace if cracked, worn, or missing to restore smooth door swing and proper alignment.