Parts for Kitchenaid KFCS22EVBL4: 02 - Freezer Liner Parts

Replace your refrigerator water filter every 6 months to ensure clean, fresh-tasting water and ice. Easy twist-on installation. Verify fit with your model.

Seals refrigerator or freezer door to prevent air leaks and maintain temperature. Replace if torn, deformed, or door won't close tightly. Confirm fit.

Repair kit for refrigerator drawer slide mechanisms. Includes gears and rod to replace stripped, broken, or missing components in pull-out drawer rails.

This outer cabinet housing provides a durable structural shell that supports internal components and protects them from debris and wear. It restores proper alignment and enclosure for safe, stable appliance operation. What it does:

• Replaces a cracked, dented, or misshapen outer housing that can allow debris or moisture into the appliance
• Restores proper mounting surfaces and clearances for panels, controls, and internal assemblies
• Helps reduce rattling or vibration caused by a compromised cabinet
• Prevents exposure of internal wiring and components to contaminants

• One outer cabinet housing

• Recommended for experienced DIYers; some disassembly of panels and components is required
• Disconnect power and any water lines before beginning work
• Keep track of screws and brackets; some fasteners may be reused

This is a gear shaft that serves as part of the drawer slide mechanism in the freezer section of your refrigerator. It helps the freezer drawer glide smoothly in and out on its track. Replace this shaft if the freezer drawer sticks, wobbles, or does not open and close properly.

Freezer or fridge light not working even with a new bulb? This light socket provides the electrical connection. Basic DIY repair with video guide.

This replacement screw secures panels, brackets, and components inside appliances. Replacing a missing or stripped fastener restores a snug, rattle-free fit using the correct #8-18 thread and 5/8-inch length.

• Fastens covers, trims, brackets, and internal parts to the cabinet/frame
• Used wherever a #8-18 x 5/8 screw is specified
• Replace if the original is missing, corroded, stripped, or will not tighten
• Symptoms: loose or rattling panels, gaps, or hardware that backs out

• Disconnect power; shut off gas/water before servicing
• Match thread and length; start by hand to avoid cross-threading
• Use the correct driver bit and tighten snugly—do not overtighten
• Inspect and replace damaged clips or tabs before securing

This is a freezer light module that houses the LED or bulb assembly inside the freezer compartment. It provides illumination when the freezer door is opened so you can see the contents clearly. Replace this module if the freezer light no longer turns on, flickers, or the housing is cracked or damaged.

This replacement screw secures specified refrigerator components—such as covers, brackets, and internal panels—so they stay properly mounted. Replace a missing, stripped, or corroded fastener to restore a tight, rattle-free fit and reliable operation.

• Provides the correct fastener for locations identified in your model's parts diagram
• Helps prevent looseness, vibration, and rattling of panels or brackets
• Replace if the head is stripped, threads are worn, or the screw is missing
• Symptoms can include loose parts, gaps, or noises from movement

• Unplug the refrigerator and shut off water if working near the ice maker or dispenser
• Match length and type to the original; follow your model's parts diagram for placement
• Start threads by hand to avoid cross-threading; tighten snugly without over-torquing, especially into plastic
• Keep track of screw positions; do not mix different screw lengths or styles

Right-hand slide bracket secures drawer or shelf slide assemblies in refrigerators. Replace if cracked, broken, or causing misalignment issues.

Left-side slide bracket that secures and guides drawer assemblies in refrigerators. Replaces worn, cracked, or broken brackets to restore alignment.

Secures panels, trim, and wire harnesses in your refrigerator to reduce vibration and rattling. Replace when clips break or parts become loose. Confirm fit with your model number before ordering.

Interior lights staying on or not working? This door switch controls refrigerator lighting and functions. Moderate DIY repair with video guide available.

This replacement screw secures panels, brackets, and components inside appliances. Replacing a missing or stripped fastener restores a snug, rattle-free fit using the correct #8-18 thread and 5/8-inch length.

• Fastens covers, trims, brackets, and internal parts to the cabinet/frame
• Used wherever a #8-18 x 5/8 screw is specified
• Replace if the original is missing, corroded, stripped, or will not tighten
• Symptoms: loose or rattling panels, gaps, or hardware that backs out

• Disconnect power; shut off gas/water before servicing
• Match thread and length; start by hand to avoid cross-threading
• Use the correct driver bit and tighten snugly—do not overtighten
• Inspect and replace damaged clips or tabs before securing

Right-side basket cradle secures and supports refrigerator storage baskets. Replace this bracket if cracked, broken, or missing to restore stability.

The lower left support cradle that holds and guides a drawer or basket inside the refrigerator, keeping it level and allowing it to slide in and out smoothly. It mounts to the interior wall of the refrigerator and bears the weight of the drawer and its contents. Replace this part if the lower left drawer is sagging, difficult to open, or has come off its track.

Creates an airtight seal to keep cold air in and moisture out. Replace when worn or torn to restore cooling performance and prevent frost buildup.

This bracket provides structural support for refrigerator drawers on the left side, helping them slide smoothly and remain stable. Located inside the refrigerator on the left interior wall, replace it when drawers sag, won't slide properly, or become loose and unstable.

This right-hand side adapter bracket secures the appliance cabinet or panel, restoring proper fit and stability. Replacing a damaged or missing bracket helps stop loose or misaligned panels and reduces rattling. What it does:

• Secures the right-side cabinet or panel to the chassis to maintain alignment and support.
• Helps eliminate panel movement, vibration and rattling that result from a cracked or missing bracket.
• Restores correct panel gaps so doors or drawers operate and close properly.

• Disconnect power (unplug or shut off breaker) before accessing the appliance.
• Remove the required access panels to reach the bracket; keep and reuse existing fasteners unless new hardware is specified by the model diagram.
• Transfer the bracket into position and fasten securely; check for proper panel alignment after installation.

This is a plastic vent grille that covers the air intake or exhaust area on the refrigerator, typically located at the bottom front or top of the unit. It allows airflow to the condenser while keeping debris out. Replace this grille if it is cracked, broken, discolored, or if missing louvers are restricting proper ventilation and causing the refrigerator to run warm.

Protective housing that covers refrigerator fan components. Replace if cracked or broken to ensure proper airflow and protection. Confirm fit with model.

Loud noise or freezer warming up? This evaporator fan blade circulates cold air over coils. Simple DIY fix—most repairs done in under an hour.

The refrigerator fan motor grommet is a small rubber cushion that mounts between the evaporator or condenser fan motor and its bracket, absorbing vibration during motor operation. It reduces noise and prevents the motor's vibration from transferring to the refrigerator cabinet. Replace this part if your refrigerator is making a rattling or buzzing noise coming from the fan area, which is often caused by a worn or deteriorated grommet.

Freezer cold but fridge warm? Your evaporator fan motor circulates air between compartments. Most DIYers complete this repair in 1 hour with our video.

Water pooling in freezer or fridge? A clogged or cracked defrost drain funnel causes leaks. DIY fix in 30-45 minutes by accessing the rear freezer panel.

Creates a watertight seal at water connections to prevent leaks. Replace when cracked, flattened, or worn. Confirm fit with your model number.

Seals the drain tube connection to prevent leaks and ice buildup in your freezer. Replace if you see water pooling or ice forming at the freezer bottom.

Freezer running too warm or too cold? This thermistor cover shields the temperature sensor for accurate cooling. Simple snap-in installation fixes misreads.

Size: 8 x 1-1/4 inch.

Replacement airflow deflector for refrigerators. Redirects air and shields internal components. Needed when original is cracked, broken, or missing.

Wire harness for bottom-mount refrigerators. Connects electrical components throughout the unit. Replace if wires are frayed, damaged, or connectors broken.