Parts for Ge PCA23VGXEFSS: 04 - Freezer Section Parts

Replace worn refrigerator door foam seal strip to improve cooling efficiency and reduce energy costs. Self-adhesive installation. Verify fit with your model.

Foam seal strip creates an airtight barrier between refrigerator components. Replace when worn, compressed, or damaged to maintain efficiency. Verify fit with your model number before ordering.

Replacement freezer lower air tower for your refrigerator. Installs in the freezer compartment to direct airflow. Needed when original is cracked or broken.

Refrigerator plenum gasket seals air duct between fresh food and freezer sections. Replace if torn, cracked, or causing temperature issues. Verify fit with your model number before ordering.

Seals evaporator cover to cabinet, preventing air leaks and frost buildup. Replace if worn or cracked to restore proper airflow and temperature control.

Upper freezer tower bracket secures the ice/tower assembly inside your refrigerator's freezer. Replace if cracked, broken, or missing to restore support.

Fix a frozen evaporator coil with this defrost heater assembly. Restores proper cooling when frost buildup blocks airflow. DIY repair in 2-3 hours.

Seals the evaporator block to the freezer cabinet, maintaining proper airflow and preventing air leakage. Replace if cooling is uneven or frost builds up.

Drip trough assembly catches defrost and condensation water in your side-by-side refrigerator. Replace if cracked, broken, or causing leaks.

Protective grille cover that mounts over the temperature sensor in your refrigerator. Replace if cracked, broken, or missing to properly shield the sensor.

Fix inconsistent temps or ice buildup on evaporator coils? This sensor seal protects accuracy. DIY-friendly with wire splicing. Video guide available.

Fix a warm fridge with cold freezer or frost buildup on coils. This defrost thermostat regulates defrost cycles. DIY repair in under 30 minutes with video.

Fix uneven cooling or defrost issues with a new temperature sensor. Most DIYers complete this repair in under an hour with basic tools and our video.

If your refrigerator isn't cooling properly or makes unusual noises, the evaporator fan assembly may need replacement. Moderate DIY repair for side-by-side models.

Replace your refrigerator plenum gasket to restore proper airflow and temperature control. Install when torn, compressed, or causing air leaks. Verify fit with your model number.

Self-adhesive foam strip seals gaps in your refrigerator to prevent air leaks and maintain temperature. Replace when worn, compressed, or damaged.

Protects the freezer light bulb from damage while maintaining visibility. Replace if cracked, yellowed, or broken. Confirm fit with your model number.

Bottom door hinge and pin assembly for side-by-side refrigerators. Replace this structural part if cracked, broken, or worn to restore door support.

Secures mobility components and wheel brackets on side-by-side refrigerators. Replace if screw is missing, stripped, or worn to restore stable mounting.

Front caster assembly that mounts to the bottom of your refrigerator. Replace if cracked, broken, or worn to restore smooth rolling and stability.

This corner cap is a small trim piece that protects and finishes the corner of an oven door. It restores the door's appearance and helps keep the glass and trim edges covered for a clean, finished look. What it does:

• Covers and protects the outer corner of the oven door trim to prevent exposed edges
• Helps secure door trim and maintain a finished appearance
• Commonly replaced when cracked, broken, missing, or loose after impact or wear
• Fits where a small molded corner protector is required

• One corner cap as shown

• Disconnect power to the appliance before attempting any repair and allow the oven to cool completely
• Remove any screws or trim pieces that obstruct access; corner caps typically snap or slide into place
• Handle door glass and metal trim carefully to avoid chips or cuts

Lower front kick grille that covers the base of your refrigerator. Replaces cracked, broken, or missing grilles to restore finished appearance.

Replace worn or broken refrigerator leveling leg roller wheels. Installs on adjustable feet to enable smooth movement and positioning of your unit.

Fix electrical connection issues in your refrigerator with this terminal block socket assembly. Connects power to components. Moderate DIY repair.

Illuminates refrigerator and freezer compartments for visibility. Replace when dim, flickering, or burned out. Verify fit with your model number.

Top hinge and pin assembly for refrigerator freezer doors. Mounts at the top of the door to allow smooth opening and closing. Replace if cracked or worn.

Replacement mounting screw for refrigerator brackets, panels, and handles. Restores secure fit when original fastener is missing, stripped, or damaged.

Fixes freezer or fridge light staying on, or ice dispenser not working when door closes. Simple 5-minute DIY fix with putty knife—video included.

Fix a warm freezer or thawing food with this evaporator fan motor. Circulates cold air over coils. DIY-friendly repair in about 30 minutes with basic tools.

Secures the lower edge of the evaporator assembly inside your refrigerator. Replace if cracked, broken, or missing to restore proper alignment.

Replace missing or stripped #8-18 x 5/8-inch Torx T20 screws in your side-by-side refrigerator. Secures panels, brackets, drawer rails, and trim.

Rattling noise or warm temps? A broken evaporator fan blade disrupts air circulation. This repair takes 30-45 minutes with basic tools and our video guide.

Rubber bumper that cushions and mounts the evaporator fan motor assembly. Replace if cracked, deteriorated, or missing to reduce vibration and noise.

Rubber grommet that seals and cushions where the evaporator fan motor shaft mounts. Replace if cracked, worn, or missing to eliminate noise and vibration.

Secures and seals water line connections in your refrigerator's dispensing system. Replace if leaking or loose to prevent water damage. Confirm fit.

Protective cap that covers the evaporator fan motor bearing and housing in freezers and refrigerators. Replace if cracked, broken, or missing to prevent debris.

Black plastic lever assembly that installs on the freezer door hinge mechanism. Replace when cracked, broken, or missing to restore proper door closure.

Replacement door closure spring for refrigerator hinges. Installs on door hinge assembly to provide tension for proper closing. Needed when broken or worn.

Fastens refrigerator panels, brackets, and internal components. Replace this screw if the original is missing, stripped, or damaged to restore secure mounting.