Parts for Ge PTS25SHSCRSS: 03 - Freezer Section Parts

Purifies water before reaching your dispenser and ice maker. Replace every 6 months for clean, safe drinking water. Verify fit with your model number.

Sheet metal screw secures refrigerator panels, trim, and brackets. Replace missing, stripped, or corroded screws to restore proper fit and assembly.

Mounting screw for freezer interior components and panels. Replace if stripped, corroded, or missing to secure shelves, racks, or trim properly.

Fix uneven cooling or defrost issues with a new temperature sensor. Most DIYers complete this repair in under an hour with basic tools and our video.

Self-adhesive foam strip that installs around the refrigerator door perimeter. Replace if the original strip is damaged, cracked, or missing to restore seal.

Self-adhesive foam insulation strip for refrigerator doors. Replaces worn, compressed, or missing foam that affects door seal and energy efficiency.

Replacement shelf for your refrigerator interior. Installs on shelf supports to organize food and beverages. Order a new one if cracked or broken.

Replacement plug cover and gasket assembly for refrigerator electrical access areas. Restores secure fit when original is cracked, broken, or missing.

Ice overflowing freezer or ice maker won't shut off? Replace the missing or broken ice bucket. Installs in minutes, no tools required.

Interior light not working? Replace a faulty refrigerator light socket to restore lighting. Simple hand repair with basic tools in under 15 minutes.

The Light Bulb (40W) is an OEM component for GE refrigerators. As an essential task lamp, it illuminates the interior of the refrigerator and freezer compartments. 

All light bulbs will eventually burn out with consistent use over many yea

Secures and seals water line connections in your refrigerator's dispensing system. Replace if leaking or loose to prevent water damage. Confirm fit.

Fix uneven cooling or defrost issues with a new temperature sensor. Most DIYers complete this repair in under an hour with basic tools and our video.

Mounting bracket that secures the evaporator fan in place inside your refrigerator. Replace if cracked, bent, or broken to properly support the fan.

Interior light not working when door opens? This light switch controls refrigerator illumination. DIY-friendly install takes 30-45 minutes with video.

Fix a warm fridge or freezer not cooling properly. This evaporator fan motor circulates cold air throughout your refrigerator. DIY repair in 30-40 minutes.

Freezer fan loud or not spinning? This evaporator fan blade circulates cold air over the coils. DIY-friendly repair with our video guide.

The Lid Bumper is an OEM part for GE refrigerators. It is designed to provide cushioning and protection for the refrigerator lid, preventing damage and ensuring smooth, quiet closing. 

Causes of a bad Lid Bumper can include deterioration o

Rubber grommet that seals and cushions where the evaporator fan motor shaft mounts. Replace if cracked, worn, or missing to eliminate noise and vibration.

Rubber grommet that mounts and cushions the evaporator or condenser fan motor. Replace if cracked, worn, or missing to prevent vibration and noise.

Fix a warm fridge or freezer ice buildup. This defrost heater melts frost on evaporator coils to restore cooling. Moderate DIY repair, 1-2 hours.

This replacement defrost heater warms the freezer's evaporator area during the automatic defrost cycle. It melts accumulated frost so air can circulate, helping maintain stable temperatures and preventing ice buildup on the back wall.

• Heats the

This holder element assembly secures the appliance's heating element in the correct position so the element stays stable for consistent operation and safe performance. It's a direct-fit replacement for worn or damaged holders. What it does:

• Secu

The Defrost Thermostat is an OEM replacement part designed for use in GE refrigerators. This component acts as a safety device in the refrigerator's defrost system, preventing the freezer from overheating during the defrost cycle. It works by monit

Secures evaporator thermistor to tubing for accurate temperature readings. Replace if broken or missing to restore proper cooling and defrost cycles. Confirm fit.

Protective cover cap for refrigerator temperature sensor. Snaps into place to shield sensor from damage. Replace if cracked, broken, or missing.

Refrigerator light lens cover protects the freezer bulb and diffuses light. Replace when cracked, yellowed, or broken to restore proper lighting.

This evaporator fan motor dust cap is an authentic OEM replacement part found on refrigerator and freezer fan motors. This dust cap prevents the fan motor bearing and housing from being damaged by dirt and debris. If the dust cap is cracked or broken, the

8-18 CA HX 1/2 S

Self-adhesive foam strip seals gaps in your refrigerator to improve energy efficiency. Replace when worn, compressed, or no longer sticky. Confirm fit with your model number.

Secures the evaporator fan assembly behind the rear freezer panel. Replace if cracked, rusted, or missing to restore proper fan mounting and clearance.

Ice maker not producing ice or stopped working? This ice maker kit restores ice production. Includes full assembly for harvesting and ejecting ice.

Ice maker not filling or water spilling? This fill cup directs water into the ice maker mold for proper ice production. Simple clip-on install.