Parts for Ge GNE21FMKBFES: Freezer Section Parts

Replace your refrigerator water filter every 6 months to maintain clean water and ice. Removes contaminants for fresh taste. Easy DIY install in minutes.

8-18 CA HX 1/2 S

Fix uneven cooling or warm spots in your refrigerator with this evaporator fan cover. Protects the evaporator coils and maintains proper airflow. Moderate DIY.

The Temperature Sensor Seal is an OEM part for GE refrigerators. This seal is designed to protect the temperature sensor from moisture and other environmental factors that could affect its accuracy and longevity. By providing a barrier against the harsh conditions within a refrigerator, such as humidity and temperature fluctuations, this seal ensures that the sensor can accurately monitor and control the refrigerator's internal temperature.

Causes of a malfunctioning Temperature Sensor Seal can include wear and tear over time, degrading the seal's effectiveness. Physical damage like tears or punctures can allow moisture to reach the sensor. Improper installation may leave gaps or loose areas around the sensor, compromising the seal.

Symptoms of a bad Temperature Sensor Seal include:

• Inaccurate temperature readings.
• Condensation or frost near the sensor location.
• Frequent cycling or unusual patterns in the refrigerator's cooling process.

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

Protective grille cover that mounts over the temperature sensor in your refrigerator. Replace if cracked, broken, or missing to properly shield the sensor.

Interior light not working when door opens? This light switch controls refrigerator illumination. DIY-friendly install takes 30-45 minutes with video.

This evaporator wire harness delivers power and control signals to the evaporator fan and defrost components. Replace a damaged harness to restore stable cooling and dependable automatic defrost performance. What it does:

• Provides plug-in electrical connections for evaporator-compartment components
• Carries power and control signals for cooling and defrost cycles
• Enables proper airflow across the evaporator and effective frost removal
• Common clues of a failing harness: heavy frost on the back wall, evaporator fan not running, intermittent cooling, or burned/brittle wires or connectors

• 1 evaporator wire harness assembly

• Disconnect power to the refrigerator before servicing
• Access the harness behind the freezer/evaporator cover; remove drawers/shelves and the rear panel
• If iced over, allow ice to melt—do not use sharp tools on coils or wiring
• Route and secure the new harness exactly like the original; fully seat each connector

Fix refrigerator cooling issues with this low side assembly. Essential component for refrigerant circulation in bottom-mount and standard models.

Rattling noise or warm temps? A broken evaporator fan blade disrupts air circulation. This repair takes 30-45 minutes with basic tools and our video guide.

Fix frost buildup or uneven cooling in your refrigerator. This defrost thermostat regulates evaporator temperature to prevent ice accumulation.

Fixes evaporator coil freezing up every 5-7 days. This defrost heater melts ice buildup on coils to restore proper airflow and cooling performance.

Ice maker producing hollow, small, or misshapen cubes? This cup fill directs water into the ice mold for consistent cube formation. Easy DIY repair.

This LED light board assembly provides the replacement LED module that illuminates the control/display area. Restores visibility of panel indicators and display lighting for proper operation and ease of use. What it does:

• Replaces the LED light module that backlights the control/display area and status indicators.
• Restores faded or non-lit control panel lighting that makes buttons and icons hard to see.
• Can resolve intermittent or no-light symptoms caused by a failed LED board.
• Works with the original housing and connectors for a direct-fit replacement.

• One LED light board assembly as shown

• Disconnect power to the appliance before starting any repair to avoid shock.
• Handle the board by edges; avoid touching LED lenses or circuitry to prevent damage.
• Verify connector orientation and seating; secure mounting screws to prevent rattle.

Protective cover for your refrigerator's interior light bulb. Replace if cracked, yellowed, or missing to restore proper illumination and a finished look. Verify fit by model number.

Fix uneven cooling or defrost issues with a new temperature sensor. Most DIYers complete this repair in under an hour with basic tools and our video.

Fix your refrigerator when it's not making ice or producing broken cubes. This icemaker assembly restores automatic ice production. DIY-friendly.

Ice maker loose, tilted, or not dispensing properly? This mounting bracket secures your ice maker assembly to the freezer cabinet, restoring alignment.

Refrigerator not cooling evenly or freezer making noise? This evaporator cover and fan assembly circulates cold air over coils for consistent temperature.