Parts for Ge PSS28KSHGCSS: Freezer Section Parts

Replace your refrigerator water filter every 6 months to maintain clean water and ice. Removes contaminants for fresh taste. Easy DIY install in minutes.

Freezer air duct plenum extension that clips into the duct opening to direct airflow. Replace if cracked, broken, or missing to restore proper air circulation.

Seals evaporator cover to cabinet, preventing air leaks and frost buildup. Replace if worn or cracked to restore proper airflow and temperature control.

Upper freezer tower bracket secures the ice/tower assembly inside your refrigerator's freezer. Replace if cracked, broken, or missing to restore support.

Fridge warm but freezer cold? Frost buildup on evaporator coils means a failed defrost heater. This assembly prevents ice blockage, restoring airflow.

Drip trough assembly catches defrost and condensation water in your side-by-side refrigerator. Replace if cracked, broken, or causing leaks.

Fix uneven cooling or defrost issues with a new temperature sensor. Most DIYers complete this repair in under an hour with basic tools and our video.

Fix inconsistent temps or ice buildup on evaporator coils? This sensor seal protects accuracy. DIY-friendly with wire splicing. Video guide available.

Fix uneven cooling or defrost issues with a new temperature sensor. Most DIYers complete this repair in under an hour with basic tools and our video.

If your refrigerator isn't cooling properly or makes unusual noises, the evaporator fan assembly may need replacement. Moderate DIY repair for side-by-side models.

Directs airflow inside your refrigerator for proper venting and component fit. Replace if cracked, warped, or broken to restore internal alignment.

Plenum shield insert for refrigerator air distribution system. Replaces cracked, broken, or missing inserts that affect airflow routing. Direct fit part.

Bottom door hinge and pin assembly for side-by-side refrigerators. Replace this structural part if cracked, broken, or worn to restore door support.

Secures mobility components and wheel brackets on side-by-side refrigerators. Replace if screw is missing, stripped, or worn to restore stable mounting.

Front caster assembly that mounts to the bottom of your refrigerator. Replace if cracked, broken, or worn to restore smooth rolling and stability.

Corner cap for side-by-side refrigerators. Covers and protects exposed corners on cabinet exterior. Replace if cracked, broken, or missing.

Decorative base grille panel that covers the condenser area at the bottom front of your refrigerator. Replace if cracked, broken, or missing.

This cover hinge replaces a worn or broken lid hinge to restore smooth opening and secure closure of the appliance cover. Designed to fit the OEM mounting points for a correct, durable replacement. What it does:

• Supports the cover/lid and allows it to pivot smoothly
• Replaces cracked, bent, or loose hinges that cause misalignment or cover sagging
• Stops rubbing, binding, or popping noises coming from the cover hinge area
• Restores proper cover seating to help maintain normal operation and safety

• Disconnect power to the appliance before starting any repair
• Typical installation requires basic hand tools; keep fasteners from the original hinge for reuse unless replacements are supplied
• Align hinge to factory mounting points and tighten hardware securely but avoid over-torquing

Top hinge and pin assembly for refrigerator freezer doors. Mounts at the top of the door to allow smooth opening and closing. Replace if cracked or worn.

Hex head screw for refrigerator panels, brackets, and assemblies. Replaces missing, stripped, or rusted fasteners to secure components properly.

Fixes freezer or fridge light staying on, or ice dispenser not working when door closes. Simple 5-minute DIY fix with putty knife—video included.

Fix uneven cooling or warm spots in your fridge with this evaporator fan motor. Restores airflow across coils when the fan runs weak, noisy, or stops.

Secures the lower edge of the evaporator assembly inside your refrigerator. Replace if cracked, broken, or missing to restore proper alignment.

Replace missing or stripped #8-18 x 5/8-inch Torx T20 screws in your side-by-side refrigerator. Secures panels, brackets, drawer rails, and trim.

Rattling noise or warm temps? A broken evaporator fan blade disrupts air circulation. This repair takes 30-45 minutes with basic tools and our video guide.

Rubber bumper that cushions and mounts the evaporator fan motor assembly. Replace if cracked, deteriorated, or missing to reduce vibration and noise.

Secures and seals water line connections in your refrigerator's dispensing system. Replace if leaking or loose to prevent water damage. Confirm fit.

Protective cap that covers the evaporator fan motor bearing and housing in freezers and refrigerators. Replace if cracked, broken, or missing to prevent debris.

Black plastic lever assembly that installs on the freezer door hinge mechanism. Replace when cracked, broken, or missing to restore proper door closure.

Replacement door closure spring for refrigerator hinges. Installs on door hinge assembly to provide tension for proper closing. Needed when broken or worn.

Fastens refrigerator panels, brackets, and internal components. Replace this screw if the original is missing, stripped, or damaged to restore secure mounting.