Parts for Ge PFSS6PKXASS: 06 - Fresh Food Section Parts

The water filter is an OEM part for GE refrigerators. This filter removes or reduces various contaminants.

Features and Benefits:

• Easy DIY replacement, typically mounted inside the refrigerator at the back of the compartment.
• Removes or reduces various contaminants in your water and ice, including lead, cysts, asbestos, atrazine, , taste and odor, chlorine, sediment, turbidity, and more
• NSF/ANSI 42 and 53 standards
• 6 Month lifespan filter
• Carbon Block media
• Micron rating: 0.5-1 micron (Class I)

When to replace your filter:

• Bad taste or odor in water and ice
• Cloudy or discolored ice
• Reduced water flow or pressure
• Refrigerator replace filter indicator light is on

Note: If replacing the Culligan metal canister design filter for the first time, a special adapter, part number AP2615702 is needed, which is not included with this part. The compatible bypass cap is part number AP6891551.

This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

A small mounting clip that secures a plastic housing or cover to the appliance frame, keeping panels aligned and internal components protected. Replaces a worn or broken clip to restore proper fit and reduce rattles. What it does:

• Secures a housing or access cover to the appliance cabinet so panels stay aligned
• Keeps wiring and internal components covered and protected from debris
• Stops covers from sagging, rattling or falling off due to a broken clip
• Helps maintain normal airflow paths and panel fit where applicable

• Always disconnect power to the appliance before inspecting or servicing panels
• Typically fastens with snap-in engagement or a small screw; basic hand tools may be required
• Handle plastic panels and clips gently to avoid cracking; replace any damaged adjacent fasteners

This temperature sensor monitors internal refrigerator temperatures and relays them to the control, helping the unit maintain consistent cooling. Replacing a failed sensor restores accurate temperature regulation and more reliable operation. What it does:

• Measures compartment or evaporator temperature and sends a resistance signal to the control board
• Helps the control modulate compressor and fan run times for proper cooling
• Typical failure signs: sections too warm or too cold, erratic temperatures, or running longer than normal
• Causes inaccurate temperature readings compared to setpoints

• 1 temperature sensor assembly

• Disconnect power before servicing
• Access the sensor in the affected section; release any cover/clip and unplug the connector
• Route the new sensor's wiring like the original and ensure it's fully seated in its holder or clip
• Restore power and allow up to 24 hours for temperatures to stabilize

The Evaporator Drain Tray is an OEM part for GE refrigerators. It is responsible for catching the water that melts from the evaporator coil during the cooling process. It ensures that the water is properly drained and does not accumulate inside the refrigerator.

A bad evaporator drain tray can be caused by clogging or blockage in the drain line, damage to the tray itself, or malfunctioning of the defrost system.

Symptoms of a bad evaporator drain tray include:

• Water pooling at the bottom of the refrigerator.
• Excessive frost or ice build-up in the freezer compartment.
• Leaking or dripping water from the refrigerator.

Replace your worn-out or damaged evaporator drain tray with this OEM part and prevent water-related issues in your refrigerator. This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

This is an evaporator cover and fan assembly that is used for the fresh food sections on refrigerators. This component makes up the back wall of the fresh food compartment and circulates the air over the evaporator to keep the food longer. If food is not staying as fresh for as long, it's a good idea to check this part for any damage and to ensure that it is working properly. The motor makes noise, such as a high pitched sound, if the evaporator fan motor is going bad. If that's the case, the entire evaporate and fan assembly will need to be replaced. Disconnect the refrigerator from its power source before replacing this part. Wear work gloves to protect the hands during this process.This evaporator cover and fan assembly is sold individually. It's a genuine OEM part that comes straight from the manufacturer. This part is compatible with refrigerators that are manufactured by GE.

This temperature sensor monitors interior temperatures so the refrigerator can maintain proper cooling. It connects to the control board and provides the temperature readings the appliance needs to regulate compressor and fan operation. What it does:

• Detects air temperature in the refrigerator/freezer compartment for accurate control signals
• Helps the control board decide when to run cooling cycles
• Commonly replaced when interior temps are incorrect or fluctuate unexpectedly
• Can address symptoms like the fridge running constantly, not cooling properly, or erratic temperature behavior

• One temperature sensor (thermistor) with connector

• Disconnect power before attempting any service to avoid electrical shock
• Handle the sensor and lead gently; avoid kinking or sharply bending the probe
• Mount and route the wiring per original placement so the sensor reads ambient compartment temperature

This is a self-tapping screw used to secure appliance panels and small components. It provides a reliable hold in sheet metal and plastic mounting points to restore proper fit and prevent rattling or loose parts. What it does:

• Fastens trim, brackets, and light-duty panels where a tapped hole is needed
• Creates its own threads in thin metal or plastic mounting points
• Helps stop vibration-related noise by securing loose panels
• Commonly used during repairs of control panels, inner liners, and external trim

• One tapping screw as shown

• Use the correctly sized screwdriver or bit to avoid stripping the head
• Drive straight and stop when snug; over-tightening can strip the mating material
• Turn power off and unplug the appliance before accessing internal panels
• If the original hole is damaged or oversized, consider using a slightly larger fastener or repair insert per manufacturer guidance

This water tank assembly holds and directs refrigerated water for dispensing and ice production, restoring normal water flow and supply to the ice maker and dispenser. Easy-to-replace reservoir designed to fit the factory mounting points. What it does:

• Stores and supplies water to the ice maker and dispenser.
• Routes incoming water through internal channels to the icemaker/dispenser valves.
• Helps maintain steady water flow when the dispenser or icemaker calls for water.
• Commonly replaced for symptoms like leaks, visible cracks, no/low water to dispenser, or ice maker not filling.

• Turn off the refrigerator and shut off the water supply before starting.
• Disconnect electrical power and water line fittings carefully to avoid damage.
• Inspect and replace associated gaskets or quick-disconnect fittings if they are worn or leaking.
• Handle the reservoir gently to avoid cracking; test for leaks and proper fill after reassembly.

Water filter head and tubing assembly holds the water filter and connects the water lines to the water filter. Approximate dimensions: 10.5" x 10.4" x 4.6"

The water filter is an OEM part for GE refrigerators. This filter removes or reduces various contaminants.

Features and Benefits:

• Easy DIY replacement, typically mounted inside the refrigerator at the back of the compartment.
• Removes or reduces various contaminants in your water and ice, including lead, cysts, asbestos, atrazine, , taste and odor, chlorine, sediment, turbidity, and more
• NSF/ANSI 42 and 53 standards
• 6 Month lifespan filter
• Carbon Block media
• Micron rating: 0.5-1 micron (Class I)

When to replace your filter:

• Bad taste or odor in water and ice
• Cloudy or discolored ice
• Reduced water flow or pressure
• Refrigerator replace filter indicator light is on

Note: If replacing the Culligan metal canister design filter for the first time, a special adapter, part number AP2615702 is needed, which is not included with this part. The compatible bypass cap is part number AP6891551.

This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

The water filter cover attaches over the water filter and protects the water filter and head. Approximate dimensions: 7" x 7" x 2.6"

This motor cover protects the damper motor assembly, keeping the motor and linkage free from debris for reliable vent operation. It helps shield internal components to reduce wear and prevent foreign object interference. What it does

• Guards the damper motor and linkage from dust, crumbs and other debris
• Maintains proper clearance around the motor to help consistent damper movement
• Can reduce rattling or contact noise caused by loose components
• Useful when replacing a cracked, broken or missing motor cover

• One motor cover

• High-level replacement: remove power, access the damper assembly, remove fasteners, swap the cover, and reassemble
• Always disconnect power before servicing to avoid electrical shock
• Keep track of screws and any small parts during disassembly
• If the damper motor or linkage are damaged, replace those components rather than relying on the cover alone

This damper motor assembly controls the refrigerator air damper to help regulate airflow between compartments, restoring proper temperature balance and reducing uneven cooling when the original motor fails. What it does:

• Moves the air damper to open or close airflow between freezer and fresh-food sections
• Allows the fridge control to direct colder or warmer air as needed for temperature regulation
• A faulty unit can cause symptoms like warm or inconsistent fresh-food temperatures, reduced cooling performance, or unusual clicking/noise at the damper area

• Disconnect power before starting; work on powered appliances can cause shock or injury
• Access typically requires removing interior panels or shelving to reach the damper housing
• Align the motor drive and damper linkage; don't force gears or clips when installing
• After installation, restore power and verify damper movement and temperature control operation