Parts for Ge GTH18DCDLRBB: Fresh Food Section Parts

Vegetable pan support bracket for top-mount refrigerators. Installs inside the crisper drawer compartment. Replace if cracked, broken, or missing.

Fastens panels, brackets, and trim to appliance cabinets. Replace this screw when the original is missing, stripped, or damaged during service work.

Bottom housing cover for refrigerator electronic dispenser control assembly. Replaces cracked, broken, or missing enclosure. Protects internal components.

Fix a refrigerator that won't defrost or has an iced-up evaporator coil. This defrost control board manages defrost cycles to prevent frost buildup.

Replace cracked or broken control panel housing for your refrigerator. This protective cover installs over the electronic control area to secure components.

Front mobility wheel for refrigerators. Mounts to the bottom front of your unit to allow smooth rolling movement. Replace if cracked, broken, or worn.

Leveling leg threads into the refrigerator base to support and stabilize the cabinet. Replace if cracked, broken, or worn to keep your unit level.

Black corner cap cover for top-mount refrigerators. Replaces cracked, broken, or missing corner trim pieces. Installs on exterior cabinet edges.

Small washer that fits on refrigerator door hinges to distribute weight and reduce friction. Replace if worn, cracked, or missing to restore proper alignment.

Bottom door hinge and pin assembly for refrigerator doors. Replaces broken, worn, or missing hinges that cause door misalignment or sagging issues.

Front mobility roller assembly for refrigerators. Mounts underneath to enable smooth rolling and positioning. Replace when cracked, broken, or worn out.

Replaces a worn, cracked, or missing temperature control knob on your refrigerator. Installs on the control panel for secure grip and smooth adjustments.

Fridge warm but freezer cold? This temperature control thermostat monitors compartment temp and cycles the cooling system. DIY repair with video guide.

This nozzle control foam is a soft sealing pad that fits around the refrigerator dispenser nozzle to help cushion the nozzle and maintain a tight seal at the dispenser opening. It keeps the dispenser area neater and helps reduce splashes and drafts. What it does:

• Seals the gap around the dispenser nozzle to limit water drips and air infiltration
• Cushions and stabilizes the nozzle to reduce movement and wear
• Helps keep the dispenser opening cleaner by blocking debris entry
• Can reduce minor splatter and improve dispenser appearance

• Disconnect power and shut off the water supply before servicing the dispenser area
• Remove the dispenser bezel or outer trim to access the nozzle per your model's service instructions
• Press the foam into the nozzle cavity until it seats evenly; do not stretch or tear the foam
• Use only manufacturer-approved fasteners or clips; avoid adhesives unless your service manual specifies

Foam insulation block that installs around the refrigerator control housing. Replace if cracked, compressed, deteriorated, or missing to restore insulation.

A small canoe-shaped mounting clip used to secure tubes, wiring or small components inside the appliance, keeping lines routed and preventing rubbing or vibration for quieter, safer operation. What it does

• Secures tubing, wiring harnesses or small components to cabinet walls or frames.
• Keeps lines properly routed to prevent rubbing, chafing or pinching.
• Reduces vibration and rattling from loose parts.
• Helps maintain proper clearances that can prevent intermittent electrical contact or line wear.

• Disconnect power and shut off water before servicing.
• Verify exact clip location and orientation before removing the old clip.
• Snap into the original mounting hole or slot; do not force or bend mounting surfaces.
• Replace any damaged mounting posts or surrounding hardware to ensure a secure fit.

Spacer component that fits on the temperature control shaft inside your refrigerator. Replace if the original is cracked, worn, or missing.

Fix a slamming or misaligned refrigerator door with a new hinge damper shaft. Restores smooth, quiet closing and proper door alignment in minutes.

Push-on spring knob for refrigerator control shafts. Replaces worn, cracked, or missing knobs to restore secure grip and smooth operation of controls.

Replace your refrigerator's light shield reflector to restore proper interior lighting. This lens cover protects the bulb and directs light effectively. Confirm fit with your model number.

Interior light not working when door opens? This light switch controls refrigerator illumination. DIY-friendly install takes 30-45 minutes with video.

Replace missing or stripped mounting screws in your refrigerator. This screw secures internal components and panels. Essential for reassembly after repairs.

This genuine fastener secures appliance components such as panels and brackets. Replacing a missing or stripped screw restores proper fit and helps reduce vibration or rattling. Features 12-24 threads and an approximate 0.785-inch length. What it does:

• Fastens panels, brackets, covers, and other hardware points in the appliance
• Helps maintain proper alignment and a tight fit of components
• Replaces damaged, stripped, or missing hardware
• Common symptoms include loose or rattling parts and hardware that won't tighten

• One screw

• Disconnect power before servicing; shut off water supply if working near water components
• Start the screw by hand to avoid cross-threading; replace one-for-one in the original location
• Use the correct driver bit for the head style; tighten snugly without overtightening into plastic or thin metal

Decorative plug insert that covers mounting screws on refrigerator panels and trim. Replace if cracked, missing, or discolored to restore a finished look.