Frigidaire Cooktop Parts

Protective overlay for range touch controls. Replaces cracked, bubbled, scratched, or melted overlays from heat exposure or cleaning damage. Installs over control panel.

Replaces the thin faceplate over your range control panel. Restores clear button labels when original is worn, peeling, or faded. Easy peel-and-stick.

Adhesive control panel overlay that restores faded, peeling, or bubbled button labels on your range. Replace when graphics become unreadable or worn.

Replace your electric range's surface burner control knob if it's cracked, stripped, worn, or missing. Attaches to the valve stem to select heat settings.

Range won't turn off or functions stay powered on? This relay board controls electrical flow to range components. Common fix for stuck-on appliances.

This is a black burner cap that sits on top of a small surface burner on a gas range. It distributes the flame evenly around the burner for consistent heating. Replace this cap if it is chipped, cracked, warped, or if you notice uneven or yellow flames on the small burner.

The Knob is an OEM part for Frigidaire ranges. This component allows users to control the heat levels of the burners or the oven by turning the corresponding control shaft. It ensures precise adjustments for cooking and baking.

Over time, the knob can wear out or break due to frequent use, exposure to heat, or accidental impacts. Causes of a bad knob include cracking, stripping of the internal connection, or the knob becoming loose and difficult to turn.

Symptoms of a bad knob include:

• Difficulty in turning the knob
• Inconsistent or unresponsive heat adjustments
• The knob becoming loose or falling off
• Visible cracks or damage to the knob

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Restores proper door alignment and smooth operation when hinges are worn, bent, or binding. Replaces damaged hinges to help door sit flush and close correctly.

This wiring harness routes power and control signals between key components inside your range or wall oven. Replace a damaged harness to restore safe, reliable operation and prevent intermittent heat, shorts, or non-working burners and oven functions.

• Distributes electrical power and signals between controls, switches, heating elements/igniters, and safety components
• Maintains correct connector orientation and wire routing for dependable operation
• Typical symptoms: no heat in oven or on surface burners, intermittent operation, breaker tripping, or visible burnt/melted wiring
• Restores stable connections to reduce arcing and overheating

• Disconnect power at the circuit breaker; for gas ranges, also shut off the gas supply
• Label or photograph all connections and transfer one wire at a time to avoid miswiring
• Route the harness exactly as original; keep away from sharp edges and hot surfaces; secure with existing clips/ties
• If connectors don't match or any terminals are heat-damaged, stop and inspect mating components.

This factory screw secures panels, brackets, and other components in your cooking appliance. Replace a missing, stripped, or corroded fastener to restore a tight, rattle-free fit and keep parts properly aligned during use.

• Fastens components to maintain proper alignment and stability
• Helps prevent vibration, rattling, and loose parts during operation
• Replace if threads are stripped, the head is damaged, or the screw is missing
• Commonly used to mount internal or exterior parts in ranges and wall ovens

• Disconnect power and allow the appliance to cool; shut off gas supply if applicable
• Use the correct driver bit to avoid stripping the screw head
• Install in the original location and do not overtighten
• If the receiving threads are damaged, repair or replace the mating part before installation

Replaces cracked or broken oven door glass on electric ranges. Covers the inner cavity and allows viewing without opening the door. Essential when damaged.

Control knob for electric range stovetop elements. Mounts to the front control panel. Replace if cracked, broken, or markings are worn and illegible.

Control knob for electric and gas range burners and oven temperature settings. Replace if knob is cracked, broken, loose, or missing from your range.

Replacement wiring harness that connects control electronics to internal components, restoring proper electrical connections and reliable operation. Use when factory wiring is damaged, loose, or causing intermittent component failures. What it does:

• Routes power and signal between the appliance control board and internal components.
• Restores continuity when broken, frayed, or corroded wires cause intermittent or no operation.
• Can resolve symptoms such as non-responsive controls, lights or fans not running, or intermittent component operation.
• Keeps wiring neat and secured along original routing to prevent rubbing and stress.

• Always disconnect power (unplug or shut off breaker) before starting any repair.
• Match connector shapes and pin counts; route harness along original clips and pathways to avoid pinch points.
• Inspect mating connectors and terminals for damage or corrosion before reconnecting.

Surface burner cap for gas ranges. Fits over the burner head to protect and direct flame distribution. Replace if cracked, chipped, or missing.

This is the large surface heating unit for an electric range or cooktop. Replacing a failing unit restores consistent stovetop heat so cookware warms predictably and meals cook evenly.

• Provides the heat source for the large burner position on an electric cooktop
• Converts electrical energy into controlled cooking heat
• Replace if the burner won't heat, heats intermittently or unevenly, or shows visible breaks, blistering, or burn spots
• Loose, pitted, or discolored terminals can also indicate the unit is failing

• Disconnect power to the appliance before servicing and allow all components to cool completely
• If your model uses plug-in coils: lift slightly and pull the old unit straight out of the receptacle; align and push the new unit straight in until fully seated
• Inspect the burner receptacle for heat damage before reassembly
• Restore power and test operation on low and high settings