Frigidaire Freezer Drawer, Shelf, Pan

This trivet is a small cooktop support that stabilizes cookware and keeps pots and pans properly positioned over the burner for even heating and safer cooking. It restores proper support for a wobbly or damaged cooking surface. What it does:

• Provides a stable surface to center cookware over the burner and prevent tipping
• Maintains correct spacing between cookware and the burner for even heat distribution
• Replaces a cracked, chipped, warped, or missing trivet that causes wobble or poor contact
• Helps protect the cooktop surface and heating elements from direct contact with cookware

• One replacement trivet

• Turn off the appliance and allow all surfaces to cool completely before handling
• Remove the old trivet (no special tools usually required) and seat the new trivet in the same location/slot
• Inspect surrounding mounts and supports for damage and replace as needed

This is a right-side tilt-out end cap that replaces a damaged or missing end piece on a refrigerator/freezer tilt-out bin. Restores secure mounting and proper pivoting of the bin for smooth opening and closing. What it does:

• Serves as the right end support for a tilt-out bin, providing the pivot point and cosmetic trim
• Keeps the bin aligned so it opens and closes smoothly
• Replaces cracked, broken, or worn end caps that allow the bin to sag or fall out
• Helps prevent rattling and excessive play of the tilt-out bin

• One right-side tilt-out end cap

• High-level snap-in or screw-mount replacement; remove the bin and follow OEM instructions
• Remove stored items before servicing and support the bin while replacing the cap
• Use basic hand tools; avoid forcing parts to prevent further damage

This door shelf bin attaches to the inner door panel to hold bottles, jars, and small items. Replacing a cracked or missing bin restores secure, organized storage and helps prevent items from tipping or falling during use.

• Provides on-door storage for jars, condiments, and similar items
• Snaps into the door liner to keep items in place during opening/closing
• Replace if cracked, warped, or if end tabs are broken and the bin won't stay seated
• Symptoms include reduced door storage, items falling, or the bin popping loose

• Disconnect power before servicing
• Remove contents, then lift the old bin up and out of the door liner retainers
• Align the new bin with the slots and press down until it locks fully in place
• Distribute weight evenly and avoid overloading to prevent future damage

This replacement door bin mounts inside the appliance door to hold bottles, jars, and condiments. It restores secure, organized storage when the original bin is cracked, loose, or missing. What it does

• Attaches to the door's molded tabs/slots to provide additional storage space
• Keeps items contained and accessible along the door
• Common failure signs: cracked plastic, broken locking tabs, bin won't stay seated, items falling from the door
• Replacing a damaged bin restores proper fit and usable capacity

• One door bin

• Empty the old bin, then lift up and out to remove from the door retainers
• Align the new bin with the same slots and press down until it locks in place
• Confirm it's fully seated before loading; avoid overloading to prevent damage
• Handle plastic carefully; letting the door warm to room temperature can reduce the chance of cracking

The lower basket holds and organizes items in the bottom section of the freezer. Replace a bent, broken, or missing basket to restore tidy storage and easier access to food in the lower compartment.

• Provides stable, contained storage in the lower freezer area
• Replaces a damaged, bent, rusted, or missing lower basket
• Helps keep food visible and accessible, reducing clutter
• If the basket won't sit level or shows broken wires/coating, replacement is recommended

• Unplug the appliance before servicing
• Empty the compartment and lift out the old basket
• Set the new basket onto the lower supports and ensure it sits level and secure
• Reload items evenly to prevent tipping

This left end cap secures the end of a dishwasher rack door assembly, helping keep the rack stable and rollers aligned for smooth operation. It replaces a worn or broken cap to restore proper rack function and fit. What it does

• Covers and protects the outer end of the rack door, preventing exposed edges.
• Holds rollers or hinges in place so the rack slides smoothly.
• Helps keep the rack aligned to prevent catching or uneven movement.
• Common symptom: cracked, missing, or loose end cap causing rack wobble or noisy operation.

• Always disconnect power to the appliance before beginning repairs.
• Usually installs by snapping into place or fastening with the original screws; use basic hand tools.
• Inspect adjacent rollers and mounting hardware while replacing the cap.
• If fit feels tight, avoid forcing parts—verify orientation before final installation.

This right-side end cap replaces a worn or broken trim piece to restore a clean fit and finish on the appliance. It secures the outer edge of the assembly and helps keep adjacent components aligned. What it does:

• Covers and protects the outer edge of the assembly to prevent gaps and sharp edges
• Secures trim and helps keep shelves or panels aligned and stable
• Restores appearance when the original cap is cracked, chipped, or missing
• Reduces rattling or movement caused by a loose or damaged end cap

• Installation is typically straightforward; part snaps or screws into place
• Use basic hand tools; keep track of any fasteners for reinstallation
• Inspect mating surfaces for damage and clean before fitting to ensure a secure fit
• If work requires panel removal near electrical or sealed-system components, disconnect power and follow safety instructions in the service manual

This left-side tiltout end cap replaces the damaged or worn plastic end piece that secures and guides a fridge/freezer tilt-out or dairy bin. Restores a secure fit and smooth opening for the tilt-out assembly. What it does:

• Replaces the left end cap on a tilt-out/dairy bin assembly
• Helps keep the drawer aligned and held in place during use
• Reduces rattling or catching when opening and closing the tilt-out
• Matches OEM fit and mounting points for direct replacement

• One left tiltout end cap

• Remove contents and the tilt-out bin before attempting replacement
• Installation typically requires basic hand tools and gentle prying to disengage clips
• Inspect mating clips and housing; replace or repair any broken tabs before reinstalling

Note: For clips only, order part# 297049500.

Replacement frame shelf that secures and supports a refrigerator shelf, restoring stable storage and helping prevent sliding or tipping of items. Fits the OEM shelf opening and provides a finished trim around the shelf edge. What it does:

• Holds and supports a glass or plastic shelf so food and containers sit level and secure
• Keeps shelf edges aligned with the refrigerator liner to prevent tipping or shifting
• Restores proper shelf seating when the original frame is cracked, warped, or broken
• Helps maintain an even load distribution across the shelf surface

• 1 frame shelf

• Remove all items from the shelf and use caution handling glass components
• Many installs slide or snap the frame into place after removing the shelf; keep track of any clips or fasteners
• If the shelf or frame is damaged, replace both pieces when recommended by the OEM

This replacement basket restores storage and organization inside your refrigerator or freezer, keeping foods contained and easy to access. Durable design holds frozen or chilled items and fits into the factory track system. What it does

• Replaces a cracked, broken or missing basket that no longer supports food items
• Restores proper organization and prevents items from shifting or falling
• Slides into the original tracks to provide stable storage where the previous basket sat
• Helps maximize usable space and keeps smaller items grouped and visible

• Remove food and unplug the appliance (or turn off power at the breaker) before servicing.
• Slide old basket out of the tracks and lift out; align new basket with tracks and slide into place.
• Do not force the basket; check mounting tabs and track alignment before applying pressure.
• Handle carefully to avoid sharp edges.