Frigidaire Freezer Parts

This bracket is the factory support used to mount a component securely inside your appliance. Replacing a damaged bracket restores proper alignment and reduces vibration, keeping the part stable so it operates as designed. What it does:

• Provides a rigid mounting point for the designated component
• Maintains correct alignment to help prevent rubbing, rattling, or noise
• Replaces a cracked, bent, or missing bracket to restore secure fit
• Typical signs include vibration, a loose or misaligned part, or visible damage

• 1 bracket

• Disconnect power before servicing
• Wear cut-resistant gloves; cabinet edges can be sharp
• Reuse original screws/fasteners and any spacers or grommets from the old bracket
• Mount in the original position and tighten fasteners evenly without overtightening

This electronic control is the oven's main user interface and control board, restoring reliable cycle selection and display feedback so your range or wall oven responds correctly and settings hold as expected. What it does:

• Interprets button/touchpad inputs and sends commands to heating elements, timers and relays.
• Restores or corrects digital display, clock and oven mode functions.
• Can resolve symptoms such as blank or erratic display, unresponsive controls, incorrect bake/clean cycles, or oven failing to start.
• Works as the central board that coordinates temperature and timing signals for normal oven operation.

• Always disconnect power at the breaker or unplug the appliance before inspecting or replacing controls.
• Handle the board carefully to avoid static discharge; avoid touching circuit traces or components.
• Follow the appliance's service manual or diagram for correct wire connections and panel reassembly.

This is the electronic temperature control board for select refrigerators/freezers with EZ Set controls. It regulates interior temperature based on sensor feedback and user settings to keep food safely stored.

• Monitors temperature sensor(s) and cycles compressor/defrost as designed
• Interfaces with EZ Set user controls to adjust cooling level
• Faulty boards can cause warm or too-cold temperatures, erratic cycling, or unresponsive controls
• May resolve intermittent cooling or control panel issues when properly diagnosed

• Unplug the appliance before servicing; use ESD protection when handling electronics
• Access location varies by model; note all wire connections before removal
• Handle connectors and board carefully; avoid bending pins or stressing harnesses
• After installation, restore power and allow 24 hours for temperatures to stabilize

This defrost heater melts frost and ice buildup on the evaporator so the freezer can maintain proper airflow and cooling. Replacing a failed heater helps reduce excessive icing and restores normal cooling performance. What it does:

• Heats the evaporator coil during the defrost cycle to remove frost and ice buildup.
• Restores airflow and cooling efficiency when frost accumulation is preventing proper cooling.
• Common symptom link: heavy frost or visible ice on evaporator coils.
• Common symptom link: freezer running continuously or temperatures that are warmer than expected.

• Disconnect power to the appliance before starting any repair.
• Access the evaporator by removing the freezer rear panel; avoid sharp sheet-metal edges.
• Inspect mounting clips and wiring; replace only if damaged and reconnect all terminals securely.
• Test the heater for electrical continuity with a multimeter before and after installation; restore power and confirm the defrost cycle operates normally.

This small clip secures a component, panel, or cover so it stays firmly in place during appliance operation. Replacing a bent or missing clip restores a tight fit and helps eliminate unwanted movement or vibration.

• Retains a panel, cover, bracket, or harness at its mounting point
• Helps prevent shifting, rattling, or parts coming loose
• Direct replacement for a broken, bent, or missing clip
• Common symptoms: loose or sagging panel/cover, buzzing or rattling noises, part that will not stay attached

• Disconnect power and, if applicable, shut off gas/water supplies before servicing
• Note the original clip's orientation; take a photo for reference
• Use needle-nose pliers for removal/installation; avoid over-bending the clip
• After installation, ensure the clip is fully seated and clears any moving parts

This electronic control board manages the appliance's user interface and core control functions, restoring reliable operation when the original board fails. It replaces a damaged or unresponsive control module to help regain normal appliance control. What it does:

• Sends and receives signals to operate timers, relays, and display functions.
• Controls user inputs and on/off sequencing for the appliance's systems.
• Common symptoms of a failing board: unresponsive controls, blank or erratic display, cycles not starting or stopping, or intermittent operation.
• Use this board to replace units exhibiting control or display faults that other components have not resolved.

• Disconnect power at the breaker or unplug the appliance before starting any repair.
• Handle the board by the edges and avoid touching components; use an ESD strap if available.
• Verify wiring harness connections and fuses before and after installation.

This electronic control board manages core cooling functions in your appliance, including compressor/fan operation and the automatic defrost cycle. Replacing a failing board can restore stable temperatures and more reliable, frost-free performance.

• Regulates compressor and evaporator fan operation to maintain the set temperature
• Controls and times the automatic defrost cycle to reduce frost buildup
• Interprets inputs from sensors and user controls to coordinate system responses
• Common symptoms of a failed board: inconsistent temperatures, continuous running or short cycling, heavy frost/ice on coils, or unresponsive/intermittent controls

• Disconnect power before servicing; handle the board with ESD precautions
• Note connector locations; transfer any mounting brackets or covers from the original as needed
• Seat all connectors fully and secure the board before restoring power
• After installation, monitor temperature and defrost operation

This electronic control board serves as the appliance's controller, managing cooling functions, sensor inputs, and status indicators. Replacing a faulty controller can restore stable temperatures and reliable operation.

• Regulates cooling based on temperature-sensor feedback to maintain the set point
• Switches major loads (such as compressor and fan) on and off as designed
• Interfaces with user controls and any status lights/alarms, when equipped
• Common failure symptoms: no cooling or overcooling, constant running, erratic cycling, or unresponsive/intermittent controls or indicators

• Disconnect power before servicing; electrical shock risk
• Handle the board by the edges and use ESD protection to prevent static damage
• Note/photograph all wire connectors before removal; transfer any mounting brackets or covers from the original part
• After reassembly, restore power and allow temperature to stabilize before final evaluation

This mounting bracket secures internal components or panels to restore proper alignment and reduce vibration. A simple, direct replacement that helps stop rattling, sagging or loose panels caused by a cracked or bent bracket. What it does:

• Holds and supports a component or panel to the appliance cabinet, maintaining proper fit and alignment.
• Prevents movement and vibration that can cause noise or wear.
• Replaces cracked, bent or broken brackets that cause loose panels, misalignment or rattling.
• Restores secure attachment points so doors, drawers or control housings sit correctly.

• One mounting bracket

• Disconnect power before starting any repair to avoid shock or injury.
• Basic hand tools (screwdriver, nut driver) are typically required; retain original fasteners unless replacements are provided.
• Inspect surrounding parts and mounting holes for damage; replace any worn screws or clips.

This support is a small mounting bracket used inside the appliance to hold an interior component, such as a shelf or basket. Replacing a cracked or missing support restores a secure, level fit and helps prevent wobbling or dropping.

• Provides a stable mounting point for a shelf, basket, rail, or panel
• Keeps interior components aligned and level
• Common symptoms: shelf/basket tilts, won't seat, or falls; visible cracks or missing support
• Replace if broken, deformed, or worn to restore proper fit

• Disconnect power and clear the work area before starting
• Remove the affected shelf/basket/panel to access the mounting point
• Release the damaged support (snap tabs or remove screw), align, and install the new support
• Reinstall the component and verify it sits level and secure

Kit of 24 clips

This factory fastener secures appliance panels and components. Replace a missing, stripped, or corroded screw to restore a tight, rattle-free fit and keep brackets and covers properly aligned.

• Fastens panels, brackets, and internal parts as specified by the manufacturer
• Helps maintain alignment and reduces vibration/rattling
• Replace if the head is stripped, threads are damaged, or corrosion is present
• Symptoms include loose/missing hardware, gaps, or rattling during operation

• Disconnect power; shut off gas/water if applicable before servicing
• Use the correct driver/bit size to avoid stripping the head
• Start threads by hand to prevent cross-threading; do not overtighten
• Match screw length/thread to the location; replace in sets when required

This replacement tube restores a secure, leak-resistant fluid path in your refrigerator/freezer. Replacing a damaged or brittle tube helps prevent water where it shouldn't be and keeps the system flowing as designed.

• Provides a dedicated pathway for fluid movement within the appliance
• Helps prevent leaks caused by cracks, splits, or loose connections
• Replaces kinked or clogged tubing that can restrict flow
• Common symptoms include water leaking inside or under the unit and visible damage to the existing tube

• Disconnect power and, if applicable, shut off the water supply before servicing
• Note the original routing and connection points to ensure proper reinstallation
• Transfer and reuse any original clamps, grommets, or fittings if not supplied with the part
• Push connections fully home, secure clamps, and check for leaks after reassembly

The EVAPORATOR INSULATOR is an OEM part for Frigidaire refrigerators. It is a heat-resistant insulating pad or wrap that surrounds the evaporator coils. The insulator works to retain cool air and prevent warmer air from entering the refrigerated compartment.  

Causes of a bad insulator can include deterioration or breakdown of insulating properties over time due to aging materials. Cracks, holes, or compressed sections of the insulator result in reduced insulation performance.

Symptoms of a bad evaporator insulator include:

• Inconsistently cool or warmer fridge temperatures 
• Frost or ice buildup on evaporator coils or surrounding areas
• Higher than normal electric bills from inefficient cooling
• Warm or cold spots inside refrigerator shelves and compartments

This OEM Frigidaire replacement insulator is compatible with some Kitchenaid, Electrolux, Gibson, Kelvinator, and Kenmore side-by-side refrigerator models. 

This is an authentic OEM freezer basket bumper sourced directly from the manufacturer for use on freezer baskets. Freezer basket bumpers are attached to the baskets to keep them from sliding around inside the freezer. If the bumper breaks, the basket will not stay in place, and the contents could shift or fall out. Freezer baskets create more storage room inside a freezer. These baskets are normally located on the bottom of the freezer, with freezer racks located above. Freezer baskets are ideal for storing smaller packages that might not stack well on the racks. Over time, normal wear and tear may cause the bumper to crack or break completely; if this happens, the bumper should be replaced. Remove the contents of the freezer basket. Remove the freezer basket from the freezer. Push the new bumper onto the freezer basket. Replace the contents of the basket and put it back into the freezer. This handle freezer basket is made of high-quality, white molded plastic. It is designed for use in freezers manufactured by Frigidaire, Kenmore, Gibson, and Electrolux.