Frigidaire Microwave Parts

Hardware kit for mounting microwave to wall and cabinet. Includes screws, bolts, and washers for secure installation. Replaces lost or missing fasteners.

A replacement unified-thread screw used to secure appliance panels and internal components. Provides a direct fastener to restore secure attachment when original screws are missing, damaged, or corroded. What it does:

• Fastens panels, brackets, trim pieces, and other appliance components that use a unified-thread screw.
• Restores secure mounting to reduce rattling, movement, or misalignment of parts.
• Replaces stripped, rusted, or missing screws to help maintain safe operation.
• Works where the appliance's service manual or parts diagram specifies a unified-thread fastening point.

• Disconnect power and water before servicing for safety.
• Use the correct screwdriver or bit to avoid stripping the head; install by hand until started, then snug—do not overtighten.
• Replace like-for-like: match thread type and length to the removed screw to ensure proper fit and function.
• If other fasteners show corrosion or damage, inspect nearby hardware and replace as needed.

Replacement glass turntable tray for your microwave. Installs on the rotating support hub inside the cavity. Order when cracked, shattered, or broken.

Replacement trim frame for microwave door and control area. Restores outer appearance when original is cracked, chipped, warped, or bent. Direct-fit part.

This is a plastic bracket that holds the door interlock switches in proper alignment inside the microwave's door latch assembly. It ensures the switches are correctly positioned to detect when the door is open or closed. Replace this part if the microwave won't start, runs with the door open, or if the switch holder is cracked or broken.

This sensor detects moisture levels inside the microwave cavity during cooking and communicates with the control board to adjust cook times automatically. It is a key component for auto-cook and sensor-reheat functions. Replace this sensor if the microwave fails to properly detect doneness, overcooks or undercooks food on sensor settings, or displays a sensor error code.

3mm x 8mm screw secures trim, panels, and brackets inside your microwave. Replace missing or stripped screws to restore proper fit and alignment.

Replace your microwave's cracked, broken, or missing vent grille assembly to restore a clean appearance and proper airflow direction. Secures with snaps or screws.

This replacement tray catches and channels water under the refrigerator to prevent leaks and allow proper evaporation. It restores proper drainage and helps avoid standing water that can cause odors or damage. What it does

• Collects defrost and condensate water from the evaporator area to prevent puddling under the cabinet
• Directs water toward the evaporator/drain system so it can evaporate safely
• Helps keep the refrigerator floor and surrounding cabinetry dry
• Stops common symptoms like water pooling beneath the unit or musty smells from standing water

• One replacement tray

• Disconnect power to the appliance before any service
• Remove lower kick panel or shelves as required to access the tray; allow any standing water to drain into a bucket
• Inspect mounting location and drain channel for debris; clean before installing the new tray
• Seat the tray fully and restore panels; plug in and check for proper drainage during the next defrost cycle

This drive motor restores rotational power to the appliance's drum or agitator so loads spin and drain correctly. It's a direct-replacement motor designed to restore normal wash and spin cycles when the original motor fails. What it does:

• Provides the mechanical drive force for the washer drum/agitator so clothes tumble and spin
• Re-establishes proper agitation and spin speed control when a worn or failed motor causes no-spin or no-agitate symptoms
• Operates with the appliance's existing pulley, belt, or coupling
• Works as the core rotating component tied to load movement and draining functions

• One motor

• Disconnect power and water before beginning any repair; follow the appliance service manual for safe access
• Replacement typically requires removing cabinet panels, drive belt or coupling, and electrical connector—avoid forcing parts
• Inspect associated belts, couplings, and mounting hardware; replace worn items to prevent repeated failures

Replacement foot for countertop microwaves. Installs on the bottom to support and level the unit. Order if your original foot is cracked, broken, or missing.

Carbon filter for range hoods and over-the-range microwaves. Dimensions: 7-1/16" x 11-1/2" x 3/8" (7.0625 x 11.5 x 0.375). Rectangle shape. Removes cooking odors from cooking air. Replace when clogged, discolored, or every 6-12 months.

Replace your microwave's interior light bulb to restore visibility while cooking. Simple DIY fix when light dims or burns out. Verify fit with your model.

This is a black plastic lens and frame assembly that covers the interior lamp on a microwave oven. It protects the light bulb from grease and moisture while diffusing light inside the cooking cavity. Replace this lens if it is cracked, yellowed, melted, or missing, which can leave the bulb exposed to splatter and reduce interior illumination.