Frigidaire Range / Cooktop / Oven Control Board

This generator is the OEM replacement rotary cam assembly that times and drives mechanical sequences so your appliance operates correctly. It restores proper cycle sequencing to help eliminate failures caused by a worn or damaged cam. What it does:

• Rotates and indexes internal cams/gears to control mechanical switching and timing
• Ensures correct sequencing of cycles and component engagement
• Commonly replaces noisy, stuck, or non-indexing cam assemblies
• Helps resolve symptoms like intermittent operation, failed cycle changes, or mechanical binding

• One generator (rotary cam assembly) as shown

• Disconnect power before servicing to avoid shock or injury
• Access may require panel removal and basic hand tools
• Verify alignment and timing marks during installation for proper operation

This electronic clock timer controls oven timing functions and displays time, letting you set bake/clean cycles and timed cooking for consistent results. Replaces a worn or non-responsive oven clock to restore timed operations and display. What it does:

• Provides digital time display and timing control for bake, broil, and self-clean cycles
• Enables timed cooking/start or stop functions and delayed start features
• Replaces a clock that is blank, unresponsive, or losing time
• Works with the oven's control assembly to register user inputs and run programmed cycles

• Disconnect power at the breaker before removing the old control to avoid shock
• Handle the display and circuit board carefully; avoid touching electronics or connectors
• Ensure connectors are fully seated and mounting screws are secure before restoring power

This electronic control board manages a refrigerator's temperature and user interface, restoring proper control of cooling cycles, displays, and timed features. Replace a faulty board to regain reliable electronic control and consistent temperature regulation. What it does:

• Regulates compressor and fan cycles to help maintain set temperatures
• Interprets user inputs from the console or touchpad
• Controls display indicators and diagnostic/error signals
• Can stop or restart timed functions when the board fails

• Disconnect power to the appliance before starting any repair
• Handle the board by edges and avoid static discharge; use an ESD strap if available
• Some panel or console removal is required; keep screws and connectors organized

This electronic clock timer replaces the oven/range control clock assembly to restore timed cooking and the front-panel clock display. It provides a clear digital time readout and basic timer/clock functions for compatible appliances. What it does:

• Displays the oven/range clock and provides a countdown/count-up timer
• Controls time-based functions used by the appliance's cook cycles
• Common symptom: blank or unlit clock display
• Common symptom: timer won't start or won't advance
• Common symptom: oven won't follow timed or delayed-start settings

• Disconnect power to the appliance before starting any work to avoid shock.
• Handle the control gently; avoid touching circuit contacts or LCD surfaces.
• Verify connector orientation and fully seat wiring harnesses before reassembly.

This clock timer is the range/oven's electronic control that runs bake and broil and keeps time. Replacing a failed unit restores the display and keypad response so the oven can start and operate correctly.

• Controls oven heating by switching relays for bake and broil
• Provides clock and timer functions on the front display
• Receives keypad inputs to set temperatures, times, and cooking modes
• Typical failure symptoms: blank or dim display, unresponsive buttons, oven won't start or heat, intermittent beeping or error codes

• Disconnect power at the breaker before servicing
• Note/photograph wire locations; move connectors to the new control one at a time
• Handle the board by the edges and use anti-static precautions
• Transfer any model-specific brackets or faceplate/overlay as required and set the clock after installation

This is the electronic clock and oven control that manages bake and broil functions while displaying time, temperature, and status. Replacing a failed timer restores accurate temperature control and reliable oven operation.

• Regulates oven heating by sending power to bake and broil circuits
• Displays time, set temperature, and cycle status
• Buttons allow setting bake, broil, and timer functions
• Common failure symptoms: no oven heat, inaccurate temperature, unresponsive buttons, error codes, or a blank/partial display

• Disconnect power at the breaker before servicing
• Handle the control carefully; avoid static discharge to the board
• Note wire locations or take photos before removal
• After installation, verify operation and run a test bake

This electronic controller board manages the appliance's cycles and user interface, restoring normal operation when the original control is faulty. Replace a damaged controller to regain reliable control and consistent cycle performance. What it does:

• Receives inputs from the user interface and sensors and sends commands to motors, valves, and heaters
• Regulates cycle timing, mode selection, and display functions
• Common symptoms: unresponsive controls, no display or error codes, cycles won't start or advance

• One electronic control board

• Disconnect power to the appliance before diagnosing or replacing the board
• Handle the board carefully; avoid static discharge and touching contacts
• Verify wire harness connectors and mounting locations match before final installation
• If you see burned components or connector damage, replace associated harnesses.

This electronic control board operates the appliance's user interface and electronic functions, restoring reliable control and display responsiveness for ovens and ranges. It replaces a failing console board to help regain normal operation. What it does:

• Receives input from the touchpad/controls and manages oven/range functions
• Controls display, timers, and heating cycles according to user settings
• Can resolve symptoms like unresponsive buttons, erratic display behavior, or loss of electronic control
• Works with the appliance's power and safety systems to regulate operation

• Disconnect power at the breaker before attempting any repair to avoid shock risk
• Handle the board by edges and avoid static discharge; use an anti-static wrist strap if available
• Verify connector positions and orientation before disconnecting; take photos for reference

This main control board is the electronic module that manages your appliance's functions and user inputs, restoring normal operation when the board has failed. It replaces the appliance's primary logic/control circuit to allow proper control of cycles and features. What it does

• Interprets control panel commands and runs the appliance's programmed cycles
• Manages timing, sensors, and power distribution to subsystems
• Can resolve symptoms like unresponsive controls, erratic operation, or failure to start when the board is the fault
• Works with door, temperature, and user-interface signals to coordinate appliance functions

• One main electronic control board

• Disconnect power before attempting replacement to avoid shock or damage
• Handle the board by edges and avoid touching circuits or components
• Verify connectors and mating harnesses are fully seated during reassembly

This main electronic control board regulates core appliance functions and restores reliable operation when the original board fails. It replaces a malfunctioning control module to help return the appliance to normal cycling and user control. What it does

• Manages primary electronic functions such as compressor/fan cycling, defrost control, and user interface signals.
• Processes button/console inputs and sends commands to subsystems for normal operation.
• Common symptoms it can resolve: blank or unresponsive display, no cooling or intermittent cooling, or erratic cycles.
• Does not include mechanical components—addresses electrical/control-related failures only.

• Disconnect power before removing the old board and again before installing the replacement.
• Handle the board carefully and avoid static discharge; ground yourself or use an antistatic wrist strap.
• Note connector positions and mounting locations; transfer any brackets or standoffs from the old board as needed.