Frigidaire Wall Oven Heating Element

The Surface Element is an OEM part for Frigidaire electric ranges. It is the heating element located on the cooktop, responsible for providing the heat necessary for cooking. This component is essential for the proper functioning of your stove, ensuring consistent and reliable heating for various cooking tasks.

Causes of a bad surface element can include wear and tear from regular use, damage due to spills or overheating, or electrical failures such as a short circuit. A faulty surface element can result in uneven cooking or complete failure to heat.

Symptoms of a bad surface element include:

• Element not heating up
• Uneven heating or hot spots on the element
• Visible damage such as burns or cracks
• Element cycling on and off erratically

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Bake Element is an OEM part for Frigidaire ranges. It functions as the lower heating element responsible for baking. The element heats the bottom of the oven cavity, ensuring foods are cooked evenly from the bottom up by radiant heat transfer.

Symptoms of a bad lower baking element include:

• Uneven or poor bottom cooking of baked goods
• Foods not browning or crisping properly on the bottom
• The oven failing to reach or maintain set baking temperatures

Causes can be cracked or damaged insulators leading to short-circuiting or failure to glow red-hot. Overheating may also cause element coils to warp or break over time.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

The Bake Element is an OEM part for Frigidaire ovens, designed to provide the primary source of heat for baking. Positioned at the bottom of the oven cavity, this element heats up when electricity flows through it, radiating heat evenly throughout the oven. This consistent distribution of heat is essential for achieving perfectly baked foods, from golden-brown pastries to thoroughly cooked meats.

The most common cause for bake element issues is wear and tear from regular use. Over time, the element can become inefficient due to repeated heating and cooling cycles, or it can physically break or burn out. Additionally, accidental damage can occur during oven cleaning or when moving pans in and out of the oven.

Symptoms of a failing Bake Element include:

• The oven not heating up to the desired temperature, or taking an unusually long time to do so
• Uneven baking results, with some areas of food undercooked or overcooked
• No visible glow from the bake element when the oven is turned on, indicating it isn't heating
• Physical signs of wear or damage on the element, such as blistering, cracks, or breaks

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Bake Element is an OEM component for Frigidaire wall ovens. It is an integrated heating coil that generates heat through electric resistance when powered. Located near the bottom of the oven cavity, the bake element facilitates heating for various cooking functions like baking, roasting, or warming. This element measures approximately 13 x 11 inches.

Symptoms of a bad bake element include:

• Oven failing to reach or maintain desired cooking temperatures
• Bake cycles taking excessively long periods of time
• Hot or cold spots developing inside oven cavities
• Error codes appearing related to upper heating issues

Causes can be cracks in ceramic sheathing allowing arcing, or mineral deposits coating coils over extended use impeding heat transfer.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

The Frigidaire bake element is an OEM replacement part responsible for generating heat within the oven cavity of an electric range or oven. This part is usually positioned at the bottom of the oven, directly beneath the bottom rack or the oven's interior floor. Its primary function is to convert electrical energy into radiant heat, which is then evenly distributed throughout the oven to facilitate baking and roasting processes. As the bake element heats up, it provides the necessary temperature for cooking various dishes, ensuring even and consistent baking or roasting results.

This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

This part fixes the following symptoms:

• The oven not reaching or maintaining the desired temperature during operation.
• Prolonged preheating times or the oven taking longer to reach the set temperature.
• Audible popping or sparking sounds coming from the bake element during use.

The Bake Element is an OEM replacement part for Frigidaire ovens and ranges. Located at the bottom of the oven cavity. This fundamental component produces the heat needed for baking, roasting, and heating functions.

Causes of bake element problems involve normal wear from repeated heat cycles and heavy-duty use over many years. Extended exposure to high oven temperatures can degrade fragile coil filaments.

Symptoms of a faulty bake element include:

• Uneven or inadequate heating for baking/roasting recipes
• Slow or inefficient preheating of oven interior
• Oven temperature failing to reach desired settings
• Element coil is visibly discolored or deteriorated

This OEM Frigidaire replacement element is also compatible with Electrolux, Gibson, and Kelvinator appliance brands.

The Broil Element is an OEM part for Frigidaire ranges and wall ovens. This part is responsible for providing intense, direct heat from the top of the oven cavity during the broiling process. This allows for efficient browning, crisping, and charring of foods.

Causes of a bad broil element can include excessive use over time leading to normal wear and tear, exposure to food spills or splatters causing premature degradation, or electrical malfunctions.

Symptoms of a bad broil element include:

• Inability to achieve proper broiling temperatures
• Uneven heating or cold spots in the broiling area
• Visibly damaged, blistered, or burned-out element
• Electrical issues, such as the element not heating at all

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This is the radiant heating element that sits beneath the glass-ceramic cooktop. Replace a failed element to restore proper heat on the affected burner and ensure consistent, even cooking performance on your range. What it does:

• Converts electrical power into heat for a single surface burner under the glass cooktop
• Restores a burner that won't heat, heats weakly/unevenly, or cycles off prematurely
• Helps resolve visible hot spots, burn marks, or open breaks on the element
• Supports accurate temperature control when paired with a working switch/limiter

• 1 radiant surface element

• Disconnect power at the breaker before servicing; allow the cooktop to cool completely
• Lift/remove the glass top per your service manual to access the element
• Transfer brackets/clips and move wires one-by-one to the same terminals on the new element
• Handle carefully to avoid damaging the element or glass; verify secure connections before reassembly

The Element Surface Dual is an OEM part for Frigidaire cooktops. This dual surface element provides flexible cooking options by offering two heating zones within a single element, allowing for efficient cooking with pots and pans of various sizes.

Causes of a bad dual surface element can include wear and tear from regular use, overheating, or damage from spills and impact. A malfunctioning element can result in uneven heating or failure to heat entirely, impacting your cooking experience.

Symptoms of a bad dual surface element include:

• The element not heating up
• Inconsistent or uneven heating
• Visible damage such as burns or breaks in the element
• The element only heating on one side

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Bake Element is an OEM replacement part for Frigidaire electric ranges. This component provides direct heat from an internal coil or rods within the oven cavity, allowing for baking and other heated cooking functions.

Symptoms of a bad bake element include:

• Inability to achieve or maintain proper cooking temperatures   
• Discolored, burned, or undercooked foods
• Tripped circuit breakers or blown fuses after use

Causes stem from typical wear over years of heating use. Cracks in insulated surfaces or broken coil sections can cause inconsistencies. 

This OEM Frigidaire part is also compatible with ranges sold under the Electrolux, Gibson, Kelvinator, and various Kenmore brand names. 

The Oven Element is an OEM replacement part for Frigidaire electric wall oven models. As the primary internal heating unit, it is essential for baking or warming tasks requiring convection cooking.

Causes of a bad element include failure over time from consistent thermal cycling, mineral deposits interfering with current flow or damage due to accidental water exposure during cleaning.

Symptoms of a bad element are:

• Inability to achieve or maintain set oven temperatures
• The element fading, cracking, or showing signs of burnout
• Oven not functioning on bake or convection modes at all

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This broil heating element mounts at the top of the oven cavity to provide intense, direct heat for broiling and to assist with preheating. Replacing a failed element restores even broiling performance and helps the oven reach temperature properly.

• Provides high, top-down heat for broiling
• Common failure symptoms: no broil heat, uneven browning, trips breaker when broil is selected, visible hot spots or breaks in the element
• Helps with overall oven preheat and temperature recovery

• Disconnect power before service; the element is high-voltage
• Remove oven racks to access mounting screws
• Support wiring when transferring leads to the new element to prevent panel damage
• Avoid touching new element with bare hands; clean any oils from terminals

The Radiant Surface Element is an OEM part for Frigidaire ranges and cooktops. This part generates heat for cooking and boiling on the cooktop surface.

Causes of a bad Radiant Surface Element can range from electrical issues or loose connections to physical damage from impact or spillovers.  

Symptoms of a faulty Radiant Surface Element include:

• Element not heating up or providing insufficient heat
• Element glowing unevenly or only partially heating
• Cracks or damage visible on the element surface
• Burning smells or discoloration on the cooktop

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This bake element is the primary heat source for the bake cycle in your range or wall oven. Replacing a failed element helps restore proper preheating and more even results when using the bake setting.

• Provides direct heat during the bake cycle
• Works with the control/thermostat to reach and maintain set temperature
• Common failure symptoms: no heat in bake, very long preheat, won't reach temperature, uneven baking
• Visual clues: blistering, cracking, breaks, or burnt spots on the element sheath

• Disconnect power at the breaker or unplug the appliance before servicing
• Access the element from the oven cavity; remove mounting screws/bracket
• Pull the element forward carefully and move wires one at a time to the new element; do not let wires slip back into the insulation
• Ensure terminals are fully seated and the mounting plate is secure before restoring power

This replacement radiant surface element restores consistent burner heating under the glass cooktop on compatible electric ranges. It helps your cooking zone reach and maintain temperature so pots and pans heat evenly.

• Converts electrical energy into radiant heat beneath the glass surface
• Maintains set temperature by cycling on and off during operation
• Common symptoms: burner won't heat, heats weakly or unevenly, or only part of the ring glows
• May show visible scorching or breaks when inspected after access

• Disconnect power at the breaker before servicing and allow the cooktop to cool completely
• Lift/prop the glass top or remove the burner pan as your model requires to access the element
• Label and transfer wires one at a time; ensure all terminals are firmly seated
• Handle the element carefully to avoid bending or stressing the coil and supports

The Surface Element is an OEM replacement part for Frigidaire electric ranges, designed to provide efficient and even heating for cooking on the stovetop. This component is a radiant surface element commonly seen on glass and ceramic cooktops. 8 inch, 2200 watt

Causes of a faulty Surface Element can be due to overuse causing burnout, physical damage like cracks from heavy cookware, electrical issues such as faulty wiring, and corrosion disrupting heating.

Symptoms of a bad Surface Element include:

• Not heating up, indicating it may be burnt out or disconnected.
• Heating irregularly or only partially, suggesting there might be damage to the element.
• Taking longer than usual to heat up, which could point to electrical issues or reduced efficiency due to wear and tear.

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.