Frigidaire Wall Oven Burner & Related Parts

This replacement cap covers and protects a small opening or fastener on your appliance. It restores a clean, finished appearance and helps keep out dust and moisture when the original cap is missing or damaged. What it does:

• Covers a screw hole or open end as designed on the unit
• Helps block debris and moisture and can reduce rattles
• Maintains a clean, finished look and protects underlying hardware
• Replace if the original cap is cracked, loose, deformed, or missing

• 1 cap

• Disconnect power and allow any hot surfaces to cool before servicing
• Use a non-marring tool to gently remove the old cap to avoid scratching
• Align and press/snap the new cap into place; do not force
• If the cap conceals a fastener, the fastener is secure before reinstalling the cap

Restore strong, even flame on your large burner. This sealed burner head replaces the 12K position on gas ranges/cooktops, helping recover reliable lighting and consistent heat when the original head is clogged, corroded, or damaged.

• Directs gas through calibrated ports to deliver a stable, even flame on the 12K burner position
• Helps address: burner won't light or lights intermittently; weak, uneven, or yellow flames; flame lifting or sputtering
• Replace when ports are clogged beyond cleaning, or the head is warped, cracked, or corroded
• Seats over the orifice and spark igniter in sealed-burner designs

• Disconnect power and shut off gas; allow the surface to cool completely
• Remove grate and cap; lift off or unthread the old head, retaining any mounting screw
• Clean the mating surface; align the new head over the orifice and igniter so it sits flat; if screw-retained, tighten snugly only
• Reinstall cap and grate; restore gas/power and confirm proper ignition and flame

This replacement cap covers and protects its designated opening or fastener on your appliance. It restores a clean, finished look and helps shield internal areas from dust and wear when the original cap is missing or damaged. What it does:

• Covers a specific opening, fastener, or trim end to protect the area
• Helps keep moisture, grease, and debris out of the assembly
• Restores proper fit and finished appearance
• Typical symptoms include a cracked, loose, discolored, or missing cap

• 1 cap

• Disconnect power and, if applicable, shut off gas/water before servicing
• Note the cap's orientation; gently unclip, pry, or unthread the original per model design
• Seat the new cap fully and avoid forcing or overtightening
• The cap is secure and does not interfere with moving parts

Replacement snap-on cap that restores a finished appearance and helps protect underlying components from dirt and accidental contact. Fits original mounting locations to cover exposed hardware and improve appliance safety and aesthetics. What it does:

• Covers and protects exposed hardware, terminals or posts to reduce debris buildup and accidental contact.
• Restores a clean, finished look to panels, trim or appliance edges.
• Helps reduce rattling or vibration noise caused by missing trim pieces.
• Use when the original cap is cracked, broken, missing or when exposed fasteners are visible.

• Always disconnect power (and water, if applicable) before attempting any repair.
• Remove the damaged cap by hand or with a small pry tool; press the replacement cap onto the mounting post until fully seated.
• Avoid excessive force during removal/installation to prevent damage to the mounting post or surrounding trim.
• If mounting posts or clips are damaged, replace those components to ensure a secure fit.

The Gas Burner is an OEM replacement part for Frigidaire gas wall ovens and cooktops. It facilitates safe and efficient cooking by providing a controlled source of flame. 

Symptoms of a bad gas burner include: 

• Uneven or unpredictable heating across the burner surfacea
• Flames not igniting or not staying ignited
• Burner components cracking, rusting, or becoming discolored
• Gas smells coming from the burner area

Causes of gas burner issues can be wear over time, contamination of ports/orifices affecting gas flow, or damage to ignition components. Ceramic burner materials may also degrade with heavy use or exposure.

This OEM Frigidaire replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models. 

The Surface Burner Base is an OEM part for Frigidaire gas ranges. It provides a stable foundation and housing for the range's burners. Each burner base has a molded indentation to securely hold the burner assembly in place while cooking. 

Causes of a bad Surface Burner Base can include warping or distortion from overheating, cracks or punctures from impact or mishandling, or damage from corrosion over time.

Symptoms of a bad Surface Burner Base include: 

• Burners wobbling or moving out of position during use
• Gas or liquid leaks around burner housing 
• Irregular or uneven cooking performance 
• Loose, damaged, or missing burner assemblies

This genuine OEM Frigidaire base is also compatible with some Electrolux, Gibson, Kelvinator, and Kenmore models.

The Surface Burner Base is an OEM part for Frigidaire gas ranges. It provides a stable foundation and housing for the range's burners. Each burner base has a molded indentation to securely hold the burner assembly in place while cooking. 

Causes of a bad Surface Burner Base can include warping or distortion from overheating, cracks or punctures from impact or mishandling, or damage from corrosion over time.

Symptoms of a bad Surface Burner Base include: 

• Burners wobbling or moving out of position during use
• Gas or liquid leaks around burner housing 
• Irregular or uneven cooking performance 
• Loose, damaged, or missing burner assemblies

This genuine OEM Frigidaire base is also compatible with some Electrolux, Gibson, Kelvinator, and Kenmore models.

This LP conversion kit converts a compatible natural-gas range or cooktop to run on liquid propane, restoring correct fuel flow and burner performance for homes using bottled propane. It provides the parts needed for proper gas type change. What it does:

• Replaces or adjusts burner fuel delivery so the appliance operates safely on liquid propane
• Restores correct flame characteristics and heat output after conversion
• Helps resolve symptoms like burners that burn poorly, produce yellow or sooty flames, or have reduced heat on the wrong gas type
• Supports safe operation by allowing proper jet/orifice sizing and regulator settings for LP

• Conversion kit components required to convert a natural-gas range or cooktop to liquid propane

• Conversion must follow the appliance's OEM instructions exactly; keep the manufacturer's supplied procedure and torque/adjustment notes
• Require basic tools; some kits need orifice removal/installation and regulator adjustment
• Shut off gas supply and disconnect power before starting work; check for leaks after conversion using a soap solution

The Burner is an OEM part for Frigidaire gas ranges and cooktops. It is a stainless steel component that emits radiant heat from below the cooktop grates, facilitating safe, efficient cooking. 

Proper burner operation is essential for dependable cooking performance. The burner utilizes a gas control valve and orifice to deliver a precisely regulated flame that heats pots and pans quickly and evenly.

Causes of a bad burner can include cracks or holes developing from use over time, or damaged brass burners from spills or heat exposure.

Symptoms of a bad burner include: 

• Irregular or uneven cooking temperatures
• Burner flames that are too high or low  
• Yellow flame tips instead of blue
• Non-selective control or inability to adjust flames

Replacing the burner with a genuine Frigidaire part restores robust heat output. This ensures safe, efficient operation. It is also compatible with Gas ranges by Electrolux, Gibson, Kelvinator, and Kenmore.
 

The LP Conversion Kit with Instructions is an OEM replacement part for Frigidaire gas appliances. This kit is designed to convert a natural gas appliance to operate with liquid propane (LP) fuel. It includes all necessary components and instructions for a safe and effective conversion, ensuring optimal performance with propane.

Causes for needing an LP conversion kit typically include a change in the type of gas supply, such as moving to an area where propane is the primary fuel source. Proper installation is crucial to maintain safety and efficiency during operation.

Symptoms indicating the need for this kit include:

• The appliance is not functioning due to an incompatible gas type
• Incorrect or inconsistent burner flames
• Relocation to an area with propane-only gas service

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This medium crown burner sits on the gas cooktop/range burner to shape and distribute the flame for even heating. Replacing a worn or damaged crown restores reliable ignition and a consistent flame pattern on the medium-output burner.

• Distributes gas evenly around the burner for steady, uniform heat
• Works with the igniter for reliable lighting when properly seated
• Helps protect burner ports from spills and debris
• Helps with uneven or yellow flames, delayed ignition, inconsistent lighting, or visible cracks/warping

• Disconnect power and shut off gas; allow the surface to cool completely
• Remove the old crown and clean the mating surfaces
• Align the new crown with any locator pins/notches and seat it flat; if screws are present on your model, tighten gently and evenly
• Restore gas/power and test for proper ignition and flame pattern

The Cap-Burner is an OEM replacement part for Frigidaire cooktops. It is a component located at the top of each burner element on the cooktop. The cap-burner sits directly over the burner element to distribute and maintain heat levels evenly across the heating surface. 

Causes of a bad cap-burner can include warping or distortion from excessive heat exposure over time. Wet or sticky messes can also lead to clogging or blockages.

Symptoms of a bad cap-burner include: 

• Uneven or inefficient heating of pots and pans placed on the burner surface
• Hot spots or areas of excessively high heat 
• Burner elements that do not ignite or power on as expected
• Smoke or burning smells coming from below the cap-burner

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models. 

The Surface Burner Cap is an OEM part for Frigidaire ranges. It fits over the surface burner, providing a protective cover while ensuring proper gas flow and flame distribution.

A bad surface burner cap can be caused by wear and tear, damage, or improper cleaning. When the burner cap becomes faulty, it can result in issues such as uneven flames, inefficient heating, or difficulty in maintaining a consistent temperature.

Symptoms of a bad surface burner cap include:

• Uneven or flickering flames
• Difficulty in reaching desired temperatures
• Excessive gas odor during burner operation

Replace your faulty surface burner cap with this genuine OEM Frigidaire part to restore your cooktop. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.