Frigidaire Washer Bumper, Bushing, Grommet Parts

Agitator screw spacer positions and cushions the agitator screw on top-load washers to keep the agitator stable and reduce wear. It helps maintain correct agitator alignment for reliable wash performance. What it does:

• Centers the agitator and creates the correct spacing for the agitator screw
• Prevents metal-on-metal contact that can cause noise, wear, or loosening
• Helps stop the agitator from wobbling or shifting during the spin cycle
• Contributes to secure engagement between the agitator and the transmission

• Disconnect power to the washer before beginning service
• Remove the agitator per the manufacturer's service instructions to access the screw and spacer
• Install the spacer flat and seated, then reinstall the screw and agitator; follow the OEM service manual for proper fastening procedure
• Inspect the agitator and screw for wear or damage and replace as needed

This bushing is a small sleeve bearing that supports a rotating shaft and reduces metal-to-metal wear, helping restore smooth, quiet operation and proper alignment in the appliance. What it does:

• Supports and centers a rotating shaft or post to prevent wobble and friction
• Reduces wear between moving metal parts for smoother operation
• Helps stop squeaks, grinding noises, or rubbing caused by a worn support
• Restores proper alignment to improve component life and performance

• Disconnect power or unplug the appliance before starting any repair
• Inspect surrounding components and replace any visibly worn parts for best results
• Press or tap the bushing into place squarely; avoid deforming the sleeve during install

This replacement spacer positions the transmission bearing block to help maintain proper alignment and drivetrain spacing for reliable washer operation. It restores correct fit where worn or damaged spacers cause misalignment. What it does

• Centers and supports the transmission bearing block to preserve correct bearing alignment.
• Maintains the designed clearance between transmission components and the tub/drivetrain.
• Helps reduce excess vibration, grinding, or wobble caused by a shifted or worn spacer.
• Can address intermittent agitation or spinning issues when misalignment is the root cause.

• Disconnect power and turn off water supply before beginning service.
• Access requires removing the washer cabinet/tub and supporting the transmission; keep track of fasteners and orientation.
• Inspect nearby bearings, seals, and mounting hardware and replace if worn.

This rubber lid bumper cushions the washer lid to prevent hard contact and reduce noise and wear. It replaces a worn or missing bumper to help the lid close more softly and sit level. What it does:

• Acts as a soft contact point between the lid and cabinet to absorb impact
• Reduces lid slamming, rattling, and vibration during operation
• Helps keep the lid aligned and prevents cosmetic damage to the rim
• Commonly replaced when the bumper is cracked, flattened, or missing

• One rubber lid bumper

• Install by removing the old bumper and pushing the new bumper into the mounting hole or recess; hand tools may be helpful
• Ensure the appliance is powered off and disconnected before servicing
• Inspect surrounding mounting area for damage and replace any broken retainers as needed
• If the bumper is hard to seat, warm it briefly with a hair dryer to improve flexibility

This rubber grommet cushions and protects components by isolating vibration and preventing wear where parts pass through openings. It restores proper fit and reduces noise or rubbing caused by a worn or missing grommet. What it does:

• Cushions panels, housings, or shafts to reduce vibration and noise
• Protects wiring, hoses, or metal edges from abrasion where they pass through openings
• Keeps assemblies aligned by filling mounting gaps and securing components
• Common symptom: increased rattling, vibration, or chafing around the affected area

• One rubber grommet

• Disconnect power to the appliance before beginning any repair
• Remove panels or components as needed to access the grommet; hand tools may be sufficient
• Inspect surrounding parts and replace any damaged items
• Use the OEM-style grommet to ensure proper fit and function

This replacement top-panel bushing cushions and centers the oven's top panel to reduce noise, wear, and misalignment for a secure fit and smoother operation. It helps restore proper panel seating and reduces rattles or vibration. What it does:

• Positions and supports the top panel where it meets the cabinet
• Dampens vibration to help eliminate rattling or buzzing noises
• Prevents direct metal-on-metal contact that can cause wear or scratching
• Helps maintain correct panel alignment for a flush appearance

• Disconnect power to the appliance before beginning any work.
• Remove the top panel fasteners and lift the panel carefully; sharp edges may be exposed.
• Press the bushing into the panel or support hole until fully seated; confirm alignment before reattaching the panel.
• If the bushing is brittle or deformed, replace it to ensure secure fit and noise control.