Frigidaire Washer Bracket & Flange

The Installation Kit is an OEM part for Frigidaire washing machines. It is a kit that provides all the necessary installation hardware to securely mount a washing machine on a pedestal. Having a properly installed and level pedestal is important to ensure stability during the wash cycle and reduce vibration and noise.

Causes may include missing hardware, damaged or worn parts in the existing pedestal, or inadequate installation. This replacement kit from Frigidaire includes mounts, brackets, screws, and leveling components to facilitate a straightforward and proper installation.

Symptoms of a bad or improperly installed pedestal can include:

• Excessive shaking and movement of the washer during operation
• Drain leakage or hose connections coming loose over time
• The washer developing alignment or leveling issues
• Noise and sounds that worsen over repeated use

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This mounting bracket secures its associated component inside your appliance, keeping it properly positioned during operation. Replacing a bent or broken bracket helps stop rattling or vibration and restores stable, reliable performance.

• Provides a rigid mounting point to the appliance frame or assembly
• Maintains correct position and alignment of the attached component
• Helps reduce vibration and operational noise
• Common failure signs: cracks, bending, stripped holes, or the part no longer stays secured

• Disconnect power before servicing; if working on a washer, also shut off water supply
• Note the original orientation and hardware locations; transfer any clips or grommets from the old bracket
• Reinstall using existing screws and tighten evenly—do not overtighten

This mounting bracket secures internal components or panels to the appliance, restoring proper alignment and support. Designed to replace a damaged or missing bracket so doors, drawers or internal assemblies sit and operate correctly. What it does:

• Provides structural support for panels, drawers or internal components
• Restores proper alignment to reduce rattling, sagging or binding
• Replaces broken, bent or missing brackets that prevent parts from seating
• Helps maintain safe operation by keeping components firmly attached

• One mounting bracket

• Disconnect power and water before starting repairs
• Use appropriate fasteners; retain any original screws if undamaged
• Inspect surrounding mounting points for damage and replace if needed
• Wear gloves to protect against sharp edges; test fit before final fastening

This is a replacement mounting bracket that secures appliance panels and components, restoring proper alignment and stability. A direct-fit part that helps stop loose panels, rattling, or misalignment for safe, reliable operation. What it does:

• Provides a secure attachment point for panels, trim, or internal components
• Restores correct alignment to reduce rattling and vibration
• Prevents parts from shifting or coming loose during operation
• Re-establishes proper fit where a worn or broken bracket allows gaps

• One mounting bracket

• Install with appliance powered off and disconnected from power source
• Use appropriate fasteners and torque to avoid stripping or damage
• Inspect surrounding clips and hardware; replace any damaged fasteners

This top-front bracket secures the appliance's top or front panel in place to keep panels aligned and stable. Replacing a damaged bracket restores proper panel fit and reduces rattling or loose trim. What it does:

• Mounts and supports the top/front panel to the appliance frame
• Prevents panel movement that can cause noise or misalignment
• Helps maintain correct door or control-panel fit where applicable
• Used when bracket is bent, cracked, or missing mounting holes

• One top-front bracket

• Disconnect power (and water, if applicable) before starting any repair
• Remove necessary trim or panels to access the bracket; retain original fasteners unless new hardware is supplied
• Align bracket and reinstall screws securely; avoid overtightening to prevent strip-out
• If other mounting hardware is damaged, replace it to ensure a secure fit

A replacement pump mounting bracket that secures the appliance drain/pump assembly to the cabinet, restoring proper alignment and reducing movement that can cause noise or leaks. Direct-fit design for correct positioning. What it does:

• Secures the pump/drain assembly to the appliance frame to prevent shifting
• Keeps the pump aligned for reliable water flow and quiet operation
• Helps reduce vibration and rubbing that can cause noise or premature wear
• Supports proper sealing to help prevent water leaks around the pump area

• One pump mounting bracket

• Disconnect power (and water if applicable) before starting any repair
• Basic hand tools are typically required; remove access panels to reach the pump area
• Inspect related fasteners and gaskets; replace any damaged hardware for a secure fit

This console support bracket secures the range or oven control panel, keeping the console aligned and stable for reliable button and knob operation. It restores proper panel fit and reduces movement or rattling during use. What it does:

• Provides structural support for the appliance control console or control panel
• Keeps the console aligned so switches, buttons, and knobs operate smoothly
• Helps stop console sagging, looseness, vibration, or rattling during operation
• Prevents stress on wiring and switches by holding the panel in place

• Disconnect power to the appliance before beginning any repairs; for gas ranges, shut off the gas supply.
• Support the console or control panel while removing fasteners to avoid dropping the panel.
• Use the original mounting screws and fasteners; align the bracket before tightening.