Frigidaire Washer Pump

The Frigidaire Drain Pump is an OEM part for Frigidaire washing machines. It plays a crucial role in the washer's operation by removing water from the wash tub at the end of each cycle, ensuring your clothes are properly drained before the spin cycle. 

Causes of a bad drain pump can include blockages from debris such as coins, lint, or small items that escape from clothing, as well as motor or impeller damage. Electrical failures can also impair pump function, leading to inadequate water removal.

Symptoms of a bad Frigidaire Drain Pump include:

• Water not draining completely from the washer
• Unusual noises, like humming or buzzing, indicating the pump is struggling
• Washer stopping mid-cycle
• Water pooling around the base of the machine

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Drain Pump is an OEM part for Frigidaire washing machines. It's engineered to efficiently remove used water from the washer at the end of each wash cycle, playing a critical role in the appliance's ability to prepare for the next load.  

Causes of a bad drain pump include blockages from small items or debris, mechanical failure due to wear and tear, or electrical issues preventing the pump from operating. 

Symptoms of a bad Drain Pump include:

• Water not draining from the washer
• Unusual noises coming from the pump area, indicating a blockage or failure
• The washer not completing its cycle
• Error codes displayed on the washer related to draining issues

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Drain Pump is an OEM replacement part for Frigidaire front load washers. Located inside the base of the washing machine tub, it actively pumps out water through the drain hose after each cycle completion. Efficient drainage is vital for preventing standing water issues.

Causes of a bad drain pump can include mineral or scale buildup within the pump chamber or impeller over time. The water valve may fail to open fully, blocking drain flow. Bearings may wear, causing the impeller to jam.

Symptoms of a bad drain pump are:

• Incomplete water draining after the cycle
• An accumulation of water remaining in the tub
• Leaking from the base
• Error codes could indicate drainage problems.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore.

By Frigidaire. 27 inch models, 1990 and up.

This drain pump assembly actively removes water from the washer tub during drain and spin cycles, helping prevent standing water and cycle interruptions. Replacing a worn pump restores proper draining and reliable cycle completion.

• Pumps water from the tub through the drain hose to the household drain
• Common symptoms: no drain or slow draining, water left in tub, cycle stops due to drainage issues
• May present with unusual pump noises (buzzing/grinding) or leaks at the pump housing
• Restores proper water evacuation to allow cycles to finish

• Unplug the appliance and turn off water supply before servicing
• Expect residual water—use towels or a shallow pan when removing hoses
• Access the pump (front lower or rear panel varies by model); disconnect wiring and hoses, and transfer any brackets/grommets from the old pump if needed
• Clear the drain filter, sump, and hose of debris; then test for leaks after installation

This pump and hose assembly replaces the appliance's drain pump to restore reliable water removal and prevent standing water or leaks. Use this direct-fit assembly when the unit won't drain or you see leaks from the pump area. What it does:

• Pumps drain water from the appliance and routes it out through the drain hose.
• Restores normal drain cycles when a failed pump stops water removal.
• Helps stop water pooling or leaking near the pump area.
• Reduces grinding, humming, or abnormal noises tied to a failing pump.

• Always disconnect power and shut off water to the appliance before servicing.
• Secure hose connections and clamps; check routing to avoid kinks.
• After installation, restore power and run a short drain cycle to check for proper operation and leaks.

This replacement part is a dishwasher pump and motor assembly. The dishwasher pump and pump motor circulate water through the dishwasher's spray arm. When the spray arms aren't spraying properly, this could mean that it's time for a new pump and motor assembly. While this might seem like a difficult repair, replacing the pump and motor assembly is a fairly simple process.Start by making sure the dishwasher is unplugged. After that shut off the water supply going to the dishwasher. Then disconnect the drain line from the garbage disposal or sink drain. Open the dishwasher door and pull out the bottom dish rack. Proceed to remove the upper dishrack from its track.After that, release the spray arm on the bottom of the washer. Then proceed to release the feed tube clips. Using a nut driver remove the bottom access panel and tow panel. Pull them out to remove them. Remove the power cable from the junction box, and disconnect the supply line from the inlet valve. Proceed to pull the dishwasher out of the counter. Tilt the dishwasher on its side and pull the hose from the drain pump. Remove the wire harness from the pump. Disconnect wires from diverter motor and circulation motor. Once complete, proceed to tilt the dishwasher upright and remove the pump and motor assembly from the bottom of the dishwasher. Replace with the new assembly and follow the previous steps in reverse to reconfigure the dishwasher.This genuine OEM part is compatible with is compatible with Frigidaire, Electrolux, Gibson, Kelvinator, and Westinghouse brand dishwashers.