Frigidaire Washer Dryer Combo Parts

This bushing protects the appliance service cord where it passes through the cabinet, reducing wear and preventing chafing that can expose wiring. It's a simple replacement that restores a safe cord entry point. What it does:

• Cushions and centers the service cord at the cabinet opening to prevent abrasion
• Helps keep the cord from rubbing on sharp metal edges that can cause insulation damage
• Reduces risk of shorting, sparking, or intermittent power caused by a worn cord
• Commonly replaced when the existing bushing is cracked, missing, or deformed

• One service cord bushing

• Disconnect power (unplug or switch off breaker) before servicing
• Inspect the cord and surrounding insulation; replace the cord if damage is found
• Push the bushing into the cabinet opening, then route the cord through the bushing until seated
• Reuse only if undamaged; do not force a damaged bushing into place

This mechanical temperature control thermostat regulates refrigerator temperature to keep food cold and cycling the compressor as needed. Replaces a faulty control to restore proper cooling performance and temperature stability. What it does:

• Senses cabinet temperature and opens/closes the compressor circuit to maintain set temperature.
• Stops the compressor when the refrigerator reaches the selected temperature and restarts it as needed.
• Commonly replaced when the fridge runs continuously, won't reach set temperature, or has erratic cooling cycles.
• May produce a clicking sound when switching or fail to make electrical contact, causing cooling loss.

• Disconnect power to the appliance before starting any repair.
• Access may require removing interior panels or control housing; keep track of fasteners and wire locations.
• Verify wiring and operation with a multimeter; replace only with the correct OEM part.

Specs: 8 - 18 x 0.500

This padded washer is a cushioned fastener washer that helps protect surfaces and reduce vibration where a bolt or screw passes through. It cushions metal-to-metal contact and helps prevent damage and loosening. What it does:

• Cushions and protects mating surfaces from wear and scratching
• Dampens minor vibration and reduces noise around the fastening point
• Helps maintain a secure connection by filling gaps and distributing load
• Commonly used where a soft barrier is needed between a fastener and equipment panel

• One padded washer

• Inspect the washer for damage or compression before reuse; replace if deteriorated
• Position the padded side toward the surface that needs protection
• Use the correct bolt or screw size for a snug fit; avoid over-tightening which can compress the pad
• Follow all safety precautions: unplug power and remove water supply before servicing appliances

This backsheel clip secures the appliance backsheet to the cabinet, keeping panels aligned and preventing gaps. It's a simple replacement that restores proper panel fit and reduces rattling or movement. What it does:

• Holds the backsheet or rear panel in place for a flush fit
• Stabilizes the cabinet to reduce vibration and noise
• Helps maintain proper airflow paths by keeping panels sealed
• Replaces damaged, broken, or missing mounting clips

• High-level, screwless snap-in or push-fit — remove power and access the rear panel before replacing
• Use a flashlight and small flat tool to pry the old clip free if brittle or stuck
• Wear gloves to protect hands from sharp sheet-metal edges
• If multiple clips are damaged, replace all affected clips for even panel alignment

For a complete drum bearing and shaft kit order 5303281153.

This replacement power cord restores the electrical connection for compatible Frigidaire appliances so they can safely receive power. Durable insulation and molded ends help ensure a secure, reliable feed to the appliance. What it does

• Provides the main AC power connection between the appliance and the household outlet.
• Replaces damaged, frayed, or burned cords that can cause power loss or unsafe conditions.
• Common symptom: appliance does not power on or loses power intermittently.
• Common symptom: visible cord damage, exposed wires, melting, or frequent tripping of a circuit breaker.

• Always disconnect the appliance from power at the breaker or unplug before installing.
• Inspect the cord routing and strain relief; replace any damaged clamps or covers.
• Tighten terminal connections securely; avoid over-torquing which can damage terminals.

This is a replacement mounting screw used to secure the defrost timer assembly to the refrigerator control housing, restoring proper fastening and preventing the timer from shifting or vibrating during operation. What it does:

• Secures the defrost timer to the control housing so the timer stays in position.
• Prevents vibration or movement that can cause intermittent contact or noisy operation.
• Helps maintain reliable defrost cycle timing by keeping the timer properly aligned.
• Addresses symptoms such as a loose or missing fastener, rattling behind the control panel, or a timer that shifts when the door is opened.

• Unplug the appliance before starting work to prevent electrical shock.
• Access the control housing or timer bracket per your model's service instructions.
• Use the correct screwdriver or driver bit; do not overtighten—stop when snug to avoid stripping.
• Retain removed hardware for reference and compare screw length/threads before installing.