Parts for Electrolux EFDC317TIW0: 03 - Front Panel / Lint Filter Parts

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

Replace a broken or damaged dryer duct assembly that's restricting airflow or causing poor drying. Channels hot air from drum to outside vent. DIY repair.

Mounting screw secures panels, brackets, and internal components in your dryer. Replace if missing, stripped, or damaged during repairs or maintenance.

Secures and protects your dryer's lint screen for effective lint capture. Replace if cracked, broken, or loose to maintain airflow and efficiency.

Replacement mounting screw that secures panels, brackets or small components in compatible appliances. Installs quickly to replace stripped or missing fasteners and help stop rattling and restore proper alignment. What it does:

• Fastens panels, trim pieces, brackets and other small assemblies to the appliance.
• Replaces stripped, corroded or broken screws that can cause loose parts or vibration noise.
• Helps restore proper alignment of doors, drawers or trim when a missing screw allows movement.
• Small appliance fastener sized for original mounting points—use the OEM screw whenever possible.

• Disconnect power and water before starting any repair.
• Start the screw by hand to avoid cross-threading; use the correct screwdriver or bit.
• Tighten snugly but avoid overtightening to prevent stripped threads or damaged plastic.

This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.

• Fastens the drum baffle/lifter (vane) to the rotating drum
• Helps maintain proper tumble and load turnover
• Common symptoms: loose or wobbly baffle, rattling or clunking noises, items catching on a raised baffle edge, or a baffle that detaches
• Visual cues: missing screw or stripped/damaged threads at the baffle mounting holes

• Disconnect power before servicing; shut off gas
• Access the baffle from inside the drum; align holes and start the screw by hand to avoid cross-threading
• Tighten firmly but do not overtighten to prevent stripping the drum or cracking the baffle
• Start all screws before final tightening to seat the baffle evenly

Replacement mounting screw for dryers. Secures panels and internal components. Needed when original screw is stripped, damaged, missing, or causing loose parts.

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

Replace your dryer door gasket to restore an airtight seal and improve drying efficiency. Install when gasket is torn, cracked, or allows air leaks. Confirm fit with your model number before ordering.

Replacement screw for dryers and laundry centers. Used throughout the cabinet to secure panels, drum supports, and components. Replace if missing or stripped.

Fix a laundry center door that won't stay closed with this door latch set. Restores secure closure when latches are worn or broken. Simple repair.

Dryer not starting or shutting off mid-cycle? A faulty wire harness disrupts electrical signals to motors, heating elements, and controls. Moderate DIY repair.

This door switch senses whether the appliance door is closed and signals the controls to run only when it's safe. Replacing a worn or intermittent switch restores dependable starts and proper shutoff when the door opens. What it does:

• Detects door position and allows operation only when the door is fully closed
• Interrupts operation when the door opens for safety
• Common symptoms include: won't start, stops when the door is moved, or "door open" message/error
• Intermittent starts due to worn actuator or internal switch contacts

• 1 door switch

• Disconnect power before servicing
• Access the switch from the front or top panel; release mounting screws or tabs
• Move wires to the new switch one at a time to maintain correct positions, then secure the switch
• Test operation before reassembly

The Lint Filter is an OEM component for Frigidaire dryers. As an important safety component, the lint filter screens out lint and other debris from the airflow before it exits the dryer. Trapping lint inside the filter helps reduce fire hazards and maintains peak airflow for more efficient drying performance.

Symptoms of a bad lint filter include:

• Excessive drying times as airflow is reduced
• Buildup of lint inside the dryer cabinet beyond the filter screen
• Lint escaping from the back of the dryer and collecting outside
• The lint filter itself is cracked or damaged

Causes of a lint filter issue include failure to clean the filter after each use, resulting in a blockage over time. Natural wear and tear or accidental damage can also render the filter unusable.

This OEM Frigidaire replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Secures hose connections in dryers to prevent leaks and maintain proper airflow. Replace if hoses are loose or disconnected. Verify fit with model.

Pan head mounting screw for dryers. Secures internal components and panels. Replace if stripped, missing, or damaged during appliance maintenance.

Replace your laundry center's cover if cracked, broken, or missing. This protective panel installs on the exterior to restore appearance and function.

This hinge assembly is the mounting cup that secures the refrigerator door hinge to the cabinet, restoring proper alignment so the door opens and closes smoothly and seals correctly. What it does:

• Provides a stable mounting point for the door hinge to keep the door aligned.
• Prevents door sagging and uneven gaps that can cause poor seals or cooling loss.
• Eliminates binding, grinding, or noisy hinge operation when worn or damaged.
• Helps restore smooth opening/closing after worn or cracked hinge supports.

• Unplug the appliance and remove food from the door area before beginning work.
• Support the door while removing hinge fasteners to prevent sudden drops or damage.
• Use hand tools to remove/install mounting hardware; transfer any hinge pins or cams as needed.
• Test door alignment and operation after installation.

Washer that fits between the support roller and shaft in your dryer. Replace if worn, cracked, or missing to maintain proper drum alignment and support.

Supports and guides the dryer drum as it rotates. Replace if the roller is cracked, worn, or causing noise. Sold individually, not pre-assembled.

Replacement nut that secures internal components in dryers. Restores clamping force when original nut is stripped, worn, or missing. Prevents loosening.

Seals your dryer door to prevent heat loss and improve drying efficiency. Replace if stretched, collapsed, or air is escaping. Verify fit with model.

Structural frame for dryers and laundry centers. Replace if your unit's frame is cracked, bent, or damaged. Installs as the main support structure.

Replacement mounting screw for dryers. Secures panels, brackets, and internal components. Replace if stripped, missing, or corroded during repairs.

Secures dryer vent hose connections to prevent air leaks and maintain proper airflow. Replace if rusted, cracked, or loose. Confirm fit with your model.

Clear glass window for dryer door. Allows viewing of laundry during cycle. Replace if cracked, broken, or cloudy. Installs in door frame assembly.

Clear outer window for dryer doors. Provides visibility into the drum during operation. Replace if cracked, scratched, or broken for safety and aesthetics.

Secures components inside your dryer to prevent shifting during operation. Replace this retainer if it's damaged, missing, or broken to eliminate noise.

The High Temperature Adhesive is an OEM part for Frigidaire appliances. This adhesive is specifically formulated to withstand high temperatures and is used in various repair applications within appliances such as ovens, ranges, and dryers.The 1-ounce tube contains adhesive formulated to withstand the extreme heat inside dryer drums and cabinets

Causes of a bad adhesive can include exposure to extremely high temperatures over extended periods, contamination by dirt or grease, or the natural aging and drying out of the adhesive.

Symptoms of a bad high temperature adhesive include:

• Components or parts becoming loose or detached
• The adhesive becoming brittle or cracked
• Inability to properly bond surfaces exposed to high heat
• Visible deterioration or peeling of the adhesive

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.