Parts for Ge DCVH660GH3GG: 02 - Front Panel Parts

A replacement reversible plug door that covers and protects the appliance power inlet while letting the cord exit left or right for tidy cord routing. Restores a clean back panel appearance and helps keep the power connection protected from debris. What it does:

• Covers the power inlet opening to protect the plug and inlet from dust and debris.
• Reversible design lets you route the power cord to either side to fit against the wall.
• Helps keep the cord tucked close to the appliance so the unit can sit flush with cabinetry or walls.
• Replace when the door is cracked, broken, missing, or no longer holds the plug securely.

• Always unplug the appliance before starting any repair or inspection.
• May require access to the rear panel; check your owner's manual for disassembly steps.
• Check orientation before finalizing installation to ensure correct left/right cord routing.

This reversible door plug fills the unused mounting hole when you switch the door swing on your refrigerator. It restores a finished appearance and helps keep air and moisture from entering through the opening.

• Covers the unused door hole created during a door swing reversal
• Helps maintain proper sealing and resists drafts/condensation at the opening
• Restores a clean, finished, factory look to the door
• Common symptoms: missing or cracked plug, exposed hole, cosmetic gap on door edge

• Disconnect power before servicing any door components
• Gently pry out the old plug with a plastic trim tool to avoid scratches
• Align the new plug with the opening and press until fully seated and flush
• Verify the door closes properly and the gasket seals evenly

Package of 12

The Lint Filter Assembly is an OEM part for GE dryers. This part captures lint and debris from the air flowing through the dryer, preventing these particles from clogging the vent and ensuring efficient airflow.  

Causes of a bad lint filter assembly can include physical damage such as cracks or breaks, wear and tear from regular use, or clogging from excessive lint buildup that can't be cleaned effectively.

Symptoms of a bad lint filter assembly include:

• Lint buildup on clothes after drying
• Longer drying times
• The dryer overheating
• Visible damage or warping of the filter assembly

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Trap Duct Assembly is an OEM part for GE dryers. This part directs the airflow from the dryer drum to the exhaust vent. This assembly ensures efficient drying by guiding hot air out of the dryer while collecting lint and debris in the trap, preventing it from clogging the venting system.

Causes of a bad trap duct assembly can include lint buildup over time, physical damage due to heavy usage, or obstruction from foreign objects. 

Symptoms of a bad Trap Duct Assembly include:

• Reduced drying efficiency or longer drying times
• Excessive lint buildup around the dryer
• Overheating of the dryer
• Unusual noises during the drying cycle

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Trap Duct Assembly is an OEM part for GE dryers. This part directs the airflow from the dryer drum to the exhaust vent. This assembly ensures efficient drying by guiding hot air out of the dryer while collecting lint and debris in the trap, preventing it from clogging the venting system.

Causes of a bad trap duct assembly can include lint buildup over time, physical damage due to heavy usage, or obstruction from foreign objects. 

Symptoms of a bad Trap Duct Assembly include:

• Reduced drying efficiency or longer drying times
• Excessive lint buildup around the dryer
• Overheating of the dryer
• Unusual noises during the drying cycle

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Lower Drum Felt seal is an OEM replacement part for GE dryers. The Lower drum felt seal is responsible for creating a seal between the drum and the front panel of the dryer.

This part fixes the following symptoms:

• Air leaking from the dryer drum
• Reduced dryer efficiency and increased energy costs
• Clothes becoming caught in the gap between the drum and front panel
• Potential damage or snags to clothes or the dryer

Causes of a bad Lower Drum Felt Seal can range from normal wear and tear, which degrades the felt material over time, to excessive load sizes that strain the drum and seal. Additionally, over time, the seal can become compressed or damaged, leading to a less effective seal and the potential for heat loss and inefficiency in the drying process.

This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 

The Drum Support Bearing is an OEM part for GE dryers. It is designed to support the rear of the dryer drum, ensuring smooth and stable rotation during the drying cycle. This bearing reduces friction and wear on the drum and motor, contributing to efficient and quiet dryer operation.

You should replace the drum support bearing if it becomes worn out or damaged. Causes of a bad drum support bearing can include regular wear and tear from frequent use, lack of lubrication, or debris accumulation. A faulty bearing can lead to increased friction and noise, affecting the dryer's performance.

Symptoms of a bad drum support bearing include:

• Squeaking or grinding noises during the drying cycle
• The dryer drum not rotating smoothly or being off-balance
• Increased drying times or uneven drying of clothes
• Visible wear or damage to the bearing

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Note: 10-watt bulb

The Lamp is an OEM part for GE dryers. This part illuminates the dryer's drum interior, enhancing visibility for loading and unloading garments. It ensures that users can easily see their clothes and any items inside the drum, particularly useful in low-light conditions. 

Replacing a non-functional dryer lamp is important for maintaining the functionality and convenience of your GE dryer, ensuring you can effectively manage your laundry. 

Symptoms of a malfunctioning dryer lamp include:

• A lack of light inside the drum when the dryer door is opened or during operation
• Flickering or intermittent light indicating a loose connection or nearing the end of the lamp's lifespan
• Complete failure to illuminate, which could stem from a burnt-out bulb or electrical issues within the dryer

This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 

The Dryer Front Bearing Drum Slide (White, 2-Pack) is an OEM replacement part for GE dryers. These slides are located on the front panel of the dryer and work to support the drum as it rotates. The white slides are designed to reduce friction between the drum and the panel, ensuring smooth operation and helping to prolong the life of the appliance.

Over time, these slides can wear out due to constant movement, heat, and friction. When worn or damaged, the drum may not rotate as intended, leading to noise and reduced efficiency.

Symptoms of bad dryer front bearing drum slides include:

• Squeaking or grinding noises during operation
• The drum appearing loose or sagging at the front
• Clothes not drying evenly or taking longer to dry
• Visible wear or thinning on the existing drum slides

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Dryer Front Bearing Drum Slide (Green, 2-Pack) is an OEM replacement part for GE dryers. These slides are located on the front panel of the dryer and work to support the drum as it rotates. The green slides are designed to reduce friction between the drum and the panel, ensuring smooth operation and helping to prolong the life of the appliance.

Over time, these slides can wear out due to constant movement, heat, and friction. When worn or damaged, the drum may not rotate as intended, leading to noise and reduced efficiency.

Symptoms of bad dryer front bearing drum slides include:

• Squeaking or grinding noises during operation
• The drum appearing loose or sagging at the front
• Clothes not drying evenly or taking longer to dry
• Visible wear or thinning on the existing drum slides

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This cleaning felt mounts on the dryer's front shroud. It lightly contacts the rotating drum to wipe away lint and residue, helping keep the drum edge clean and supporting consistent airflow to the lint filter.

• Provides a soft wiper against the drum rim to reduce lint and residue buildup
• Helps maintain smooth drum rotation and a clean front duct area
• Wear signs include frayed or missing felt, lint trails on fabrics, or light squeaks at the front
• Visual inspection is recommended if lint accumulates inside the drum after cycles

• Disconnect power; for gas dryers, also shut off gas supply
• Access the front panel/shroud and note the original felt's orientation before removal
• Clean the mounting surface; install the new felt in the same position (some models use clips or adhesive)
• Hand-rotate the drum to ensure even, light contact before reassembly and testing

The Trap Duct Assembly is an OEM part for GE dryers. This part directs the airflow from the dryer drum to the exhaust vent. This assembly ensures efficient drying by guiding hot air out of the dryer while collecting lint and debris in the trap, preventing it from clogging the venting system.

Causes of a bad trap duct assembly can include lint buildup over time, physical damage due to heavy usage, or obstruction from foreign objects. 

Symptoms of a bad Trap Duct Assembly include:

• Reduced drying efficiency or longer drying times
• Excessive lint buildup around the dryer
• Overheating of the dryer
• Unusual noises during the drying cycle

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Door Switch is an OEM part for GE dryers, designed to ensure the dryer does not operate when the door is open. This safety feature is crucial for preventing accidents and ensuring the appliance operates efficiently and safely. The switch signals the dryer's control system about the status of the door—if it's open or closed—thereby allowing or preventing the start of a drying cycle. 

Causes of damage to the door switch often include mechanical wear from repeated use, accidental damage from loading or unloading, or electrical issues such as short circuits. 

Symptoms of a bad Door Switch include:

• The dryer not starting when the door is closed 
• The dryer continuing to run when the door is opened
• Unusual noises or the dryer stopping mid-cycle

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This replacement screw secures appliance panels and internal components per your model's hardware list. Replace lost or stripped screws to keep assemblies tight, reduce vibration and rattles, and maintain proper alignment.

• Fastens brackets, covers, and sheet-metal panels as specified in the parts diagram
• Restores proper fit when an original screw is missing, stripped, or damaged
• Helps eliminate rattling or vibration from loose hardware
• Keeps components safely in place during operation

• Disconnect power to the appliance before servicing
• Match length, head style, and thread to the original; install in the same location/quantity
• Start threads by hand to avoid cross-threading; tighten with the correct driver
• Do not overtighten, especially into plastic or thin sheet metal

Replacement screw that secures appliance panels and internal components, restoring proper fit and helping prevent rattling or misalignment. Use this fastener when original screws are stripped, missing, or damaged to keep parts stable and secure. What it does:

• Secures panels, trim pieces, brackets and other components to maintain proper alignment and fit.
• Replaces stripped, corroded, or missing screws that can cause rattling, vibration, or loose parts.
• Restores stable mounting for service panels and access covers to reduce noise and movement during operation.
• Simple hardware replacement — helps prevent secondary damage caused by loose or shifted components.

• Disconnect power or gas (when applicable) before servicing to avoid shock or injury.
• Use the correct screwdriver or bit to avoid stripping the head; turn until snug—do not overtighten.
• Keep track of small parts and wear eye protection when working in tight spaces.
• If threads are damaged, replace with the correct OEM screw rather than forcing reuse.

The Door Strike is an OEM part for GE dryers. This component is crucial for ensuring that the dryer door latches properly when closed. It interacts with the door catch mechanism to secure the door during operation, preventing it from opening unexpectedly, which ensures the dryer operates safely and efficiently.

Symptoms of a failing Door Strike include:

• The dryer door not staying closed during a cycle
• Difficulty in closing the dryer door or getting it to latch properly
• The dryer not starting because the door switch is not engaged
• Visible damage or wear on the door strike

Causes of a bad door strike can include wear and tear from regular use, physical damage from slamming the door or mishandling, and misalignment caused by repeated opening and closing.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Note: If the door catch is also needed, use part number WE1M1011.

This replacement screw secures dryer panels and assemblies, helping prevent vibration and keeping components properly aligned. Use it to replace missing or stripped hardware and restore a solid, factory-tight fit during reassembly.

• Secures panels, brackets, and internal assemblies in the dryer cabinet
• Replaces lost, damaged, or stripped factory screw
• Helps reduce vibration and rattling caused by loose hardware
• Supports proper alignment of parts and a tight fit
• Symptoms can include loose or shifting panels, rattling noises, or gaps

• Disconnect power before servicing; for gas dryers, also shut off the gas supply if moving the unit.
• Match screw length and location to the original during reassembly.
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening.
• Use the correct driver for your screw head style as used on your model.

This strike plate mounts at the door opening and works with the door latch/strike to keep the appliance door securely closed during operation. Replacing a worn plate helps restore positive latching and reliable cycle start/stop via the door switch.

• Provides the catch surface for the door latch/strike to engage
• Helps keep the door closed and properly aligned
• Enables the door switch to engage so the cycle can run
• Common symptoms include: door won't stay closed, door pops open, unit won't start unless the door is pressed, visible wear or bending on the plate

• Disconnect power before servicing
• Open the door and remove the screws securing the existing plate
• Align the new plate with the latch/strike and fasten securely with the existing hardware
• Test door closure and latch engagement; adjust alignment if necessary

This Nut-Strip Door Guide secures the door guide/strip to the appliance, helping keep the door aligned and operating smoothly. Replace a worn or missing nut to restore proper fit and prevent the guide from loosening. What it does

• Fastens the door guide/strip to the appliance frame or door
• Keeps the door guide stable to maintain proper door alignment
• Helps prevent the guide or trim strip from shifting or falling off
• Commonly replaced when the guide is loose, missing, or stripped

• Disconnect power to the appliance before beginning any repair.
• Use appropriate hand tools (screwdriver/socket) and avoid over-tightening to prevent damage.
• Inspect the door guide/strip and surrounding fasteners; replace any damaged parts for proper fit.

Replacement screw that secures appliance panels and internal components, restoring proper fit and helping prevent rattling or misalignment. Use this fastener when original screws are stripped, missing, or damaged to keep parts stable and secure. What it does:

• Secures panels, trim pieces, brackets and other components to maintain proper alignment and fit.
• Replaces stripped, corroded, or missing screws that can cause rattling, vibration, or loose parts.
• Restores stable mounting for service panels and access covers to reduce noise and movement during operation.
• Simple hardware replacement — helps prevent secondary damage caused by loose or shifted components.

• Disconnect power or gas (when applicable) before servicing to avoid shock or injury.
• Use the correct screwdriver or bit to avoid stripping the head; turn until snug—do not overtighten.
• Keep track of small parts and wear eye protection when working in tight spaces.
• If threads are damaged, replace with the correct OEM screw rather than forcing reuse.

This metal mounting plate supports the dryer door strike/catch interface. It provides a solid anchor point so the door latches securely, helping the dryer start and run only when the door is properly closed.

• Reinforces the latch area to keep the door securely closed
• May help when the door won't stay shut or the dryer won't start unless the door is held closed
• Useful if the existing plate is bent, loose, or missing
• Helps prevent vibration-related door pops during a cycle

• Unplug the dryer before servicing
• Open the door and remove fasteners securing the old plate; retain hardware if reusable
• Position the new plate and tighten screws evenly—do not overtighten
• Test door closure and latch engagement before restoring power

The Trap Duct Assembly is an OEM part for GE dryers. This part directs the airflow from the dryer drum to the exhaust vent. This assembly ensures efficient drying by guiding hot air out of the dryer while collecting lint and debris in the trap, preventing it from clogging the venting system.

Causes of a bad trap duct assembly can include lint buildup over time, physical damage due to heavy usage, or obstruction from foreign objects. 

Symptoms of a bad Trap Duct Assembly include:

• Reduced drying efficiency or longer drying times
• Excessive lint buildup around the dryer
• Overheating of the dryer
• Unusual noises during the drying cycle

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.