Parts for Ge PFD95ESPT0DS: Front Panel Parts

The Roller Assembly Wheel is an OEM part for GE dryers. It supports the drum and allows it to rotate smoothly during drying cycles, ensuring efficient and quiet operation. The assembly includes the roller, roller axle shaft, and two retaining clips. The roller is threaded on one side and hexagon-shaped on the other, with a tri-ring included for secure installation.

You should replace this roller assembly wheel if it becomes worn or damaged. Common causes of a bad roller assembly wheel include wear and tear from regular use, accumulation of lint and debris, or damage due to overloading the dryer.

Symptoms of a bad roller assembly wheel include:

• Thumping or squeaking noises during operation
• The drum not rotating properly or getting stuck
• Uneven drying of clothes
• Excessive vibration or movement of the dryer

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

A flat steel washer that spaces and protects fasteners to keep components aligned and reduce wear. Fits where a thin, durable metal shim is needed to distribute load and prevent screw or bolt damage. What it does:

• Distributes clamping force from a fastener to protect softer surfaces
• Maintains proper spacing and alignment of components
• Reduces wear and abrasion between parts
• Can help reduce loosening from vibration when used with the correct fastener

• Disconnect power and unplug the appliance before servicing.
• Use the correct bolt or screw; do not overtighten—tighten to snug plus a short turn.

This pulley nut secures the washer's drive pulley to the shaft to keep the belt aligned and power transfer reliable. Replacing a worn or missing nut restores stable spin performance and helps prevent belt slippage and noise.

• Locks the drive pulley to the shaft for proper belt alignment and consistent power transfer
• A loose or stripped nut can cause pulley wobble, belt squeal, slippage, or the belt coming off
• Replace if the original nut is damaged, missing, or will not stay tight after adjustment

• Disconnect power and water supply; safely tip or elevate the washer for bottom access
• Remove the drive belt; hold the pulley while loosening the nut (verify thread direction—do not force)
• Hand-start the new nut to avoid cross-threading; tighten securely per service information and confirm pulley runs true
• Reinstall the belt, verify alignment, and rotate by hand before restoring power

This stainless steel machine screw secures appliance components and trim for a reliable, corrosion-resistant hold. Use it when replacing lost or damaged fasteners to restore proper fit and reduce noise or misalignment. What it does:

• Fastens panels, brackets, and small assemblies where a #8-28 threaded screw is required
• Provides a rust-resistant connection for wet or humid appliance areas
• Helps stop rattling, loose trim, or misaligned parts caused by missing or stripped screws

• Disconnect power to the appliance before servicing
• Use the correct screwdriver or driver bit to avoid stripping the head
• Thread carefully by hand to avoid cross-threading; tighten until snug—do not overtighten
• Keep removed screws organized to ensure correct reassembly

The Lint Filter is an OEM component for GE clothes dryers. Located inside the dryer cabinet behind the door, this filter screens lint and other debris from the air stream before it is recirculated during the drying cycle. Consistent lint filtering is essential for safety and performance.

Causes of a lint filter becoming clogged or damaged could be a failure to clean after each use, dryer vent duct restrictions slowing airflow, or material deterioration from heat and extended use.  

Symptoms of a bad lint filter include:

• Slow or inefficient drying times  
• Excessive warmth of the cabinet, burner housing or vent ductwork
• Burned lint smell or visible lint buildup in the duct or venting area
• Tripped thermal fuses or blown heating elements due to restricted airflow

This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 

A #8-18 x 9/16-inch hex washer head screw used to secure panels and components in appliances. Provides a proper fit for fast, reliable fastening when replacing missing, damaged, or stripped screws. What it does:

• Secures panels, brackets, and trim to keep components aligned and stable.
• Restores proper fastening when threads are stripped, the original screw is missing, or a head is damaged.
• Helps stop rattling or loose parts caused by worn or broken fasteners.
• Fits applications requiring a #8-18 thread with a 9/16" length and hex washer head style.

• Verify thread size, head style, and length before installation.
• Use the correct hex driver or socket to avoid cam-out or head damage.
• Do not overtighten; snug until secure to avoid stripping threads or deforming parts.
• Disconnect power and follow appliance-specific safety steps.

This is a #8-18 x 1/2" screw used to secure panels and trim on compatible appliances. It replaces lost or damaged fasteners to restore proper fit and prevent rattling or loose components. What it does:

• Fastens panels, trim, or components to appliance chassis
• Restores secure attachment when original screws are stripped or missing
• Helps eliminate rattling or vibration caused by loose hardware
• Keeps internal parts properly aligned for normal operation

• Disconnect power before servicing the appliance to avoid electrical shock
• Use the correct screwdriver or driver bit to avoid stripping the head
• Do not overtighten; snug until secure to prevent damage to threads or plastic parts
• Keep small parts away from children and pets

The Grille Housing is an OEM part for GE dryers. Located at the front of the dryer, the grille housing covers and protects the drying drum opening. It is responsible for preventing lint buildup and maintaining airflow into and out of the dryer. 

Causes of a bad grille housing can include cracks or breaks from repeated cleaning or impact, as well as loose or worn fittings that no longer provide a proper seal. 

Symptoms of a bad grille housing include:

• Excessive lint accumulation around the dryer opening 
• Inefficient drying times due to blocked airflow
• Loose or misaligned grille that does not close properly
• Leaks around the drum opening when the dryer is running

This GE replacement part is compatible with Hotpoint, RCA, and Kenmore models.

This front drum support assembly centers and supports the dryer drum so it turns smoothly and quietly. Replacing a worn front drum support restores stable drum rotation and helps stop rubbing, scraping or loud operation. What it does:

• Holds the front of the drum in place and provides a low-friction surface for smooth rotation
• Reduces drum wobble and helps maintain even tumbling
• Prevents metal-to-metal contact that can cause scraping or grinding noises
• Helps prolong life of drum bearings/seals by keeping drum properly aligned

• Disconnect power before starting work and ensure dryer is fully de-energized
• Support the drum when removing or installing the support to avoid damage
• Inspect surrounding seals, rollers and fasteners; replace any worn components
• Tighten hardware securely but avoid overtorque; run a test cycle to ensure quiet, steady operation

This sensor rod harness connects a temperature sensor to the appliance wiring, restoring proper signal transmission for accurate temperature monitoring and control. It's a direct-fit replacement when the original harness is damaged or intermittent. What it does:

• Provides the electrical connection between the sensor rod and the control board to transmit temperature readings.
• Replaces frayed, burned, or broken wiring that can cause intermittent or no temperature readings.
• Helps resolve symptoms such as erratic temperature control, long heating/cooling cycles, or fault codes related to sensor circuits.
• Maintains secure, insulated connections to prevent shorting or open circuits.

• One sensor rod harness.

• Disconnect power to the appliance before beginning any repair to avoid electric shock.
• Access may require removing panels or components; handle sensors and wiring gently to avoid damage.
• Verify connector orientation and secure clips fully; do not force connectors.

This door switch senses when the dryer door is closed so the cycle can start, and cuts power when the door opens. Replacing a faulty switch restores safe operation and consistent start/stop behavior tied to the door. What it does:

• Detects door open/closed position to enable or interrupt the motor and heater
• Stops drum rotation and heating when the door is opened
• On many models, also controls the interior drum light
• Common symptoms: dryer won't start, drum doesn't stop when door opens, interior light stays on/off incorrectly, intermittent starting

• 1 door switch

• Disconnect power before servicing
• Access the switch behind the door opening (remove the top or front panel as required by the model)
• Note wire positions; transfer connectors to the new switch and secure it in the bracket
• Reassemble and test that the dryer starts only with the door closed and stops when opened

Color: Dark Slate

The Door Strike is an OEM part for GE dryers. Positioned on the dryer frame, it securely latches the door closed during cycles. Its magnets align perfectly with the door when shut to create an air-tight barrier, enhancing energy efficiency.

Causes of failure can be normal wear, misalignment stress, or accidental damage. Over time, strikes lose effectiveness at preventing air/moisture exchange.

Symptoms of a bad door strike include:

• Excess warm air entering the dryer chamber
• The door not fully closing or latching tight
• Clothing not drying completely within expected cycles
• Buildup of lint around the door seal area

This GE part is also compatible with some Hotpoint, RCA, and Kenmore models.
 

Size: 8 - 18 ab.