Garbage Disposal Parts

This metal tailpipe directs dryer exhaust from the appliance outlet to the vent system, restoring proper airflow and helping prevent exhaust leakage. It's a direct-fit replacement that reinstates safe venting. What it does

• Channels exhaust air from the dryer outlet to the vent duct to maintain proper airflow
• Helps prevent exhaust leakage behind the dryer that can cause odor or moisture issues
• Stops rattling or misalignment at the dryer outlet caused by a damaged or bent tailpipe
• Supports safe venting performance that can affect drying efficiency

• One tailpipe

• Disconnect power; for gas dryers, shut off the gas supply before starting
• Basic tools (screwdriver/socket) typically required; follow OEM installation instructions
• Ensure the tailpipe is seated and secured to the dryer outlet and vent duct with proper clamps or screws
• After installation, check for leaks, proper alignment, and test dryer operation

This power cord supplies electricity to a range or oven so the appliance powers and heats reliably. Replace a damaged cord to restore safe, consistent power and reduce risk of shorts or intermittent operation. What it does

• Connects the range/oven to household AC power through the terminal block or connector.
• Restores power when the original cord is frayed, burned, cut, or has broken terminals.
• Stops intermittent power or loss-of-power caused by damaged wiring or loose connections.
• Provides a properly insulated, grounded connection when the correct cord type is used.

• One power cord.

• Disconnect power at the breaker before inspecting or replacing the cord; do not rely on the range's controls to kill power.
• Verify the cord matches the appliance's terminal block and strain-relief style before installation.
• Tighten terminal screws securely and secure the cord with the appliance's strain relief to prevent wire pull-out.

Snap ring (circlip) secures shafts and components in your garbage disposal to prevent movement. Replace if worn or damaged. Verify fit with model number.

This stopper assembly seals the drain opening to allow tubs or sinks to fill and hold water. It replaces a damaged or worn stopper so you can restore proper fill-and-hold function and stop unwanted leaks. What it does

• Seals the drain to hold water for washing or soaking
• Opens and closes to allow controlled draining when needed
• Stops water from leaking around a worn or damaged stopper
• Restores normal fill-and-drain operation when the original stopper no longer seals

• One stopper assembly as shown

• Turn off water supply and remove standing water before starting
• Basic hand tools usually required; follow the appliance or sink manufacturer instructions
• Inspect surrounding drain and seals during replacement; replace damaged gaskets if present

Replacement mounting flange for garbage disposers. Secures the disposer to the sink drain opening. Order a new flange if yours is cracked or corroded.

Secures the disposal unit to the sink or cabinet. Replace if cracked, corroded, or leaking. Restores proper alignment and prevents vibration.

Mounting screw for garbage disposers. Secures disposer components during installation. Replace if lost, stripped, or corroded. Standard hardware.

Seals the connection between your disposer and drain tailpipe to prevent leaks. Replace if you notice water dripping from the connection. Verify fit with your model.

The disposer sleeve is a protective collar that connects the garbage disposer to the sink drain and prevents debris from escaping. Replace it when you notice leaks around the connection point or food particles escaping into the drain area.

Rubber gasket that seals between sink and disposal flange to prevent leaks. Replace when cracked, flattened, or leaking. Verify fit with model.

Fix a garbage disposal that won't turn on with this start switch assembly. Compatible with multiple disposer models. Repair restores power control.

Secures hoses to fittings in washers and other appliances to prevent leaks. Replace when clamps lose grip or show corrosion. Confirm fit with your model.

Fix a disposal that won't start with the stopper but works with the wall switch. This auto start switch restores batch feed operation on disposers.

Outlet gasket seals the connection between your disposer and drain pipe. Replace if you notice leaks at the discharge outlet. Verify fit with your model.

Flange installation kit for garbage disposers. Includes components needed to mount and seal the disposer to your sink. Replace if damaged or missing.