Parts for Maytag MGRH451BDS: Gas Controls Parts

This factory screw secures appliance components to their mounting points. Replace missing, worn, or stripped hardware to restore a tight fit, proper alignment, and quieter operation across the affected assembly.

• Fastens panels, brackets, covers, or internal parts to the chassis or frame
• Helps maintain alignment and support, reducing rattle, vibration, or looseness
• Replaces missing or damaged screws that have backed out, broken, or stripped
• Restores secure mounting after service when original hardware is lost

• Disconnect power; shut off water or gas supplies before servicing
• Use the correct driver; start threads by hand to avoid cross-threading
• Match length and thread to the original location; do not substitute with longer hardware
• Tighten snugly; do not overtighten into plastic or thin metal

A set of four valve mounting screws used to secure the water/ice valve or valve bracket in place. These OEM-style screws restore proper valve alignment and fasten valve assemblies for reliable operation. What it does:

• Secures the valve or valve bracket to the appliance chassis to prevent movement during operation
• Helps maintain a tight seal at valve mounting points to reduce risk of leaks
• Replaces missing, stripped, or corroded valve mounting fasteners
• Restores stable valve positioning that can prevent rattling or vibration

• Disconnect power and shut off the water supply before beginning any work
• Use the correct screwdriver or bit to avoid stripping the screw heads
• Thread screws in by hand first, then tighten snugly—do not overtighten to avoid damaging the valve or mounting threads
• If existing threads are damaged, inspect the mounting boss and replace as needed

Hand-tighten wing nut secures panels, brackets, and components in ranges and ovens for tool-free adjustment. Replace when lost, stripped, or broken.

Replacement burner seal assembly that creates a sealed barrier between a sealed gas cooktop burner and the cooktop surface, helping keep spills and debris out of the burner area and restoring stable burner seating. What it does:

• Forms a gasketed seal around the burner to limit spills, crumbs, and moisture from entering the burner box.
• Helps maintain proper burner seating for consistent flame shape and heat distribution.
• Replace if the seal is torn, flattened, warped, or shows heavy discoloration from spills or heat.
• Can reduce burner ignition or flame irregularities caused by debris or a damaged seal.

• Disconnect power and shut off gas supply before servicing; allow the cooktop to fully cool.
• Remove burner cap and head per your model's service instructions before replacing the seal.
• Clean the surrounding area of grease and debris, then press the new seal into place so it seats evenly.

Sealed burner head for gas ranges. Sits on top of the cooktop to direct gas flow and create an even flame. Replace if cracked, corroded, or damaged.

This is the right hand assembly.

Replace broken or pinched gas orifice tubes feeding your range burners. Common when lifting cooktop for cleaning or repairs. DIY install in 1-2 hours.

If your gas burner won't ignite or only one igniter sparks, this spark module generates the high-voltage pulses needed to light surface burners reliably.

Burner won't light or clicks but doesn't ignite? This spark electrode creates the ignition spark at the burner head. Easy DIY fix in under 15 minutes.

Burner won't light or spark? This top burner igniter creates the spark to ignite gas on your stovetop. Easy DIY repair in under 5 minutes with a screwdriver.

Fastening screw for securing components inside appliances. Replaces lost, stripped, or damaged screws during repairs or part installations.

Oven won't heat or takes too long to preheat? A weak or failed igniter is the most common cause. Easy DIY repair, typically completed in under 15 minutes.

Burner won't ignite or flame is weak? This top burner valve controls gas flow to individual burners. Common repair for ignition and flame issues.

Burner won't ignite or flame is weak? This top burner valve controls gas flow to individual burners. Common repair for ignition and flame issues.

Range burners won't ignite? This switch spark harness routes signals from the control to igniters. DIY-friendly repair—replace one wire at a time.

Converts gas range burners from natural gas to liquid propane fuel. Includes orifices and instructions for safe fuel-type changeover installation.

Burner cap sits on top of the gas burner head to distribute flame evenly. Replace this component if cracked, chipped, or missing to restore proper appearance.