General Electric Freezer Parts

This replacement door gasket creates a tight seal around the refrigerator door to help keep cold air in and maintain consistent temperatures. It restores proper sealing to reduce frost, cycling, and energy loss. What it does:

• Seals the refrigerator door edge to prevent warm air infiltration and cold air escape
• Helps reduce interior frost buildup and excessive compressor cycling
• Restores a consistent internal temperature for better food preservation
• Can improve cooling efficiency when the original gasket is torn, warped, or compressed

• Disconnect power to the appliance before beginning any repair
• Remove the old gasket and clean the door flange/mating surface before installing the new gasket
• Work the gasket into the channel evenly, ensuring the magnetic edge seats fully around the door
• If needed, warm the gasket slightly to aid flexibility; avoid excessive heat and sharp tools

This inlet water valve controls water flow into the appliance, allowing the dispenser and ice/water systems to fill on demand. Replaces a worn or failed valve to restore water delivery. What it does:

• Opens and closes water flow when the dispenser or ice maker calls for water
• Helps maintain proper fill for ice makers and dispenser systems
• Commonly used when dispenser or ice maker does not fill, fills slowly, or runs continuously
• Can leak or drip when internal seals or solenoids fail

• One inlet water valve assembly

• Disconnect power and shut off the water supply before starting work
• Relieve water pressure and have a towel or small container ready for residual water
• Tighten fittings to manufacturer torque; check for leaks after reconnecting water

This left-hand link actuator moves a device linkage to restore proper mechanical motion in the appliance. Replacing a worn or broken actuator helps stop erratic movement and restores reliable operation at the affected linkage. What it does:

• Converts motor or lever movement into motion at the left-hand linkage
• Replaces a cracked, stuck or broken actuator that prevents proper linkage movement
• Can stop clicking, grinding or failed movement caused by a damaged link actuator
• Works where a left-side linkage needs an exact-fit actuator to restore function

• Disconnect power to the appliance before starting work
• Remove only the panels and fasteners necessary to access the actuator; label connectors if needed
• Handle plastic tabs and mounting points carefully to avoid breakage during removal and installation
• Reconnect wiring and test the mechanism through a full cycle before reassembling all panels

This support track secures and guides a refrigerator basket/drawer so it opens and closes smoothly. Replaces a worn or broken track to restore proper alignment and reduce sticking or sagging of the basket. What it does:

• Guides the basket/drawer along its path to ensure smooth sliding and proper alignment
• Holds the basket weight so the drawer doesn't sag or fall when pulled
• Helps prevent jamming, binding, or uneven movement when loading or unloading
• Reduces rattling or noise caused by a damaged or loose track

• One support track for a refrigerator basket/drawer

• Basic hand tools may be needed; disconnect power only if work affects electrical components or lighting
• Remove the basket/drawer before replacing the track for easier access
• Inspect mounting clips and screws and replace if worn or damaged

This compressor controller is the electronic control module that manages compressor start/stop functions to help the refrigerator maintain proper cooling performance. It replaces a failed controller to restore normal compressor operation. What it does:

• Monitors and controls compressor start/stop cycles for stable cooling
• Resolves symptoms such as the compressor not running, intermittent cooling, or frequent compressor cycling
• Works with the appliance's existing wiring and mounting points to perform control functions
• Does not service sealed refrigerant components; intended only for electrical control of the compressor

• Always unplug the appliance before servicing to avoid electrical shock
• Verify power is disconnected and use a multimeter to confirm before touching wiring
• Handle the module and connectors carefully to avoid ESD or connector damage

Size: 1/4 inch diameter.

This master light switch kit replaces the main oven light switch assembly so the oven light turns on and off reliably. Designed for direct-fit replacement to restore normal oven lighting control. What it does:

• Replaces the oven's master light switch assembly that controls interior lighting
• Restores the ability to turn the oven/cabinet light on and off
• Helps eliminate flickering, intermittent operation, or complete light failure
• Works with existing wiring and mounting points for a straightforward swap

• One master light switch kit (assembly) as shown

• Disconnect power to the appliance before starting any work
• Basic hand tools required; follow OEM wiring and grounding instructions
• Verify proper operation after installation before returning appliance to service

This small replacement wire retainer secures heater and sensor wiring to the evaporator area, preventing wire contact with sharp edges and maintaining proper routing for reliable defrost operation and safe airflow. What it does:

• Holds heater and thermostat/sensor wires in place near the evaporator assembly
• Prevents chafing, pinching, or accidental contact with moving or hot components
• Helps maintain correct wire routing for consistent defrost performance and temperature sensing
• Reduces risk of intermittent connections or short circuits caused by loose wiring

• Designed for a simple clip-in or screw-mount installation; inspect mounting point for clips or fasteners before replacing
• Disconnect power to the appliance before accessing the evaporator compartment
• Handle wiring gently and ensure secure seating of wires in the retainer before reassembling panels
• If any wiring or insulation is damaged, replace or repair the wiring harness per manufacturer guidance