General Electric Range Hood Clip Or Clamp

This fan clip secures the ventilation fan blade or blower wheel to the motor shaft, preventing looseness and vibration. Replacing a worn or missing clip restores a tight fit so the fan runs smoothly and maintains proper airflow.

• Holds the fan blade/blower wheel firmly on the motor shaft
• Helps reduce wobble, scraping, or rattling noises during fan operation
• Can resolve a loose or non-spinning fan caused by a failed/missing retainer
• Supports proper airflow and cooling performance

• Disconnect power and allow the appliance to cool before servicing
• Access the fan/blower assembly and note the original clip's orientation
• Seat the clip fully in the shaft groove; ensure the wheel is secure and spins freely
• Wear cut-resistant gloves and use caution around sharp metal edges

This capillary clip secures the oven thermostat's sensing bulb/capillary to the cavity wall so it stays correctly positioned for accurate temperature control. Replace a missing or damaged clip to prevent a sagging bulb and erratic oven performance.

• Holds the thermostat capillary tube/sensing bulb in place inside the oven
• Helps maintain consistent temperature regulation by keeping the bulb properly located
• Direct replacement for a broken, corroded, or missing clip
• Symptoms include a loose or dangling bulb, uneven baking, or temperature swings

• Disconnect power (and gas, if applicable) and allow the oven to cool completely
• Access the oven cavity; locate the thermostat sensing bulb and capillary along the wall or back panel
• Position the bulb/capillary and secure with the new clip; avoid kinking or crushing the tube
• Restore power, and test operation

This is a filter clip used on range hoods. It is sometimes referred to as a range hood clip or range hood clamp. There is a filter located inside the range hood that is used to filter out smells and small particles during the cooking process. The filter is held in place by the filter clip. Accidental damage, wear and tear, or misuse may cause the filter clip to fall out or no longer be capable of holding the filter. If the filter clip is missing or broken, a replacement part is required.A visual inspection will determine if the filter clip is damaged or missing. Replacing the clip filter is an easy process. Remove the old filter clip if there is one present. Line up the new filter clip in the same position and snap it into place. Wear gloves for protection. There are no special tools required to make this repair.This is an authentic OEM replacement part. It is sold as an individual unit. The filter clip is made of durable, high-quality materials. The replacement part can be installed in several different models of range appliances. It is compatible with machines produced by General Electric, Hotpoint, and RCA.

This cable clamp secures the appliance power cord where it enters the cabinet, protecting wiring from pull and chafe for safer, more reliable operation. Designed to hold the cord firmly in place and prevent accidental disconnection. What it does:

• Acts as a strain relief to prevent the power cord from pulling into or away from the appliance
• Protects wiring from abrasion and sharp edges at the entry point
• Helps maintain a secure electrical connection to reduce intermittent power issues
• Commonly used where the cord passes through a rear or bottom access panel

• Disconnect power before inspecting or replacing the clamp to avoid shock or injury
• Install at the cord entry so the clamp captures the cord jacket; tighten fastener securely but do not over-torque
• Verify the cord is correctly routed and not pinched when reassembling panels
• If any wiring or the cord jacket is damaged, replace the cord before restoring power

This installation spring is a small replacement spring used to restore proper tension and operation in the appliance mechanism. It helps return or hold moving parts in place so doors, lids, or internal linkages operate smoothly. What it does:

• Provides tension for a specific door, latch, or linkage to help ensure consistent movement and positioning
• Replaces a worn or broken spring that can cause misalignment, sagging, or intermittent engagement
• Restores spring force so mechanisms return to their resting position reliably
• Useful when the appliance exhibits loose, sagging, or non-returning components related to the spring location

• One installation spring as shown

• Disconnect power (and water, if applicable) before attempting service to avoid shock or injury
• Compare the old spring to the replacement before installation
• Installation may require basic hand tools and careful removal/replacement of clips or retainers; avoid overstretching the spring

This small plastic wire clip secures an appliance wiring harness to the cabinet or chassis, keeping wiring routed and held firmly to prevent rubbing or pinching during use. What it does:

• Holds wiring harnesses in place to reduce movement and protect insulation
• Prevents wires from contacting hot or sharp surfaces that can cause wear
• Reduces rattling or banging noises from loose wiring
• Helps prevent intermittent electrical connections caused by loose or strained wires

• One wire clip

• Disconnect power to the appliance before starting any work
• Clip typically snaps into a pre-punched hole or slides onto a flange; line up the harness and press clip until it seats
• Inspect wiring and insulation when replacing clip; route wires away from heat and moving parts
• Replace with the exact part number for a proper fit