General Electric Range Hood Motor

This replacement motor powers the blower in your ventilation unit, spinning the fan blade or wheel to move air through the housing and ductwork. Replace it when the original motor becomes noisy, stalls, or fails to start.

• Drives the fan blade/blower wheel to move air through the unit
• Restores proper airflow and ventilation performance
• Common symptoms: loud humming or grinding, won't start, slow/weak airflow, intermittent operation, overheating/shutting off
• Often needed when the shaft is seized or bearings are worn

• Disconnect power at the breaker before servicing
• Access the blower assembly; remove the grille or filters to reach the motor
• Note wire locations; transfer wiring, mounting hardware, and the fan blade/blower wheel from the old motor if applicable
• Ensure the blade/wheel spins freely before reassembly, then restore power to test

This is a blower motor assembly intended for use with range hood fans. The blower motor assembly powers the fan that circulates air over the stove. With use, the blower motor assembly may malfunction or fail. When this part becomes damaged or stops functioning correctly, a replacement part is required to continue the effective use of the fan in the range hood.Signs that the blower motor assembly needs to be replaced include a fan that doesn't turn on or a fan that makes unusual sounds when operating. The replacement of the blower motor assembly is simple. Disconnect the range from its power source before starting the disassembly of the appliance. Wear gloves for protection. A screwdriver and a nut driver are necessary to complete the repair. The blower motor assembly is located inside the range hood. Lower the fan unit, disconnect the old blower motor and connect wires to the new motor for installation.This blower motor assembly is a genuine OEM replacement part. It is sold as an individual piece. The blower motor assembly is made of durable materials. It can be installed in several different models of ranges. The blower motor assembly is compatible with appliances produced by General Electric, RCA, and Hotpoint.

This replacement motor restores reliable rotation to the component it powers, helping your appliance operate smoothly and as designed. Swap out a worn or seized motor to bring motion and performance back to normal.

• Supplies rotational power to the attached mechanism inside the appliance
• Common failure symptoms: no movement, humming without turning, grinding/squealing noises, or intermittent/slow operation
• A failed motor can lead to loss of function and unusual noise from the driven part
• Replacing the motor restores proper motion and helps maintain overall performance

• Disconnect power to the appliance before servicing
• Access the motor area; note wire locations and the motor's orientation before removal
• Transfer any brackets, grommets, or screws from the old motor as needed; beware of sharp edges
• After mounting, ensure the shaft/attached part spins freely and clear of obstructions before reassembly and testing

A blower assembly that circulates oven or range heat to support convection cooking. Replacing a worn or failed blower restores airflow for more even cooking and reduces noisy or grinding fan operation. Sold individually. What it does:

• Circulates hot air across the oven cavity to support convection and temperature consistency.
• Restores airflow that helps prevent uneven cooking or extended bake times when the blower fails.
• Common symptoms of failure: loud or grinding noise, little or no airflow from the convection fan, or reduced baking performance.
• Replaces assemblies that are worn, seized, or producing excessive vibration.

• Disconnect electrical power (and gas supply, if applicable) before starting any service.
• Allow the appliance to fully cool; remove access panels to reach the blower.
• Handle fan blades carefully to avoid damage; verify the blower spins freely and wiring connectors are secure before reassembly.

This blower assembly circulates air through the appliance to maintain proper airflow and ventilation. Replacing a worn or damaged assembly restores efficient exhausting and reduces unusual noises or poor airflow. What it does:

• Moves air through the appliance for proper ventilation and drying/performance
• Helps expel humidity, lint, and combustion byproducts
• Can resolve reduced airflow, weak performance, or excessive noise from the blower area
• Supports consistent temperature and cycle performance by maintaining airflow

• 1 blower assembly

• Disconnect power (and gas if applicable) before starting any repair
• Handle the blower carefully; edges and mounting tabs can be sharp
• Secure all mounting screws and duct connections
• Check lint traps and ducts for blockages when replacing the blower

This blower and motor assembly moves air through the appliance to support proper ventilation and heating. Replacing a worn assembly restores airflow and can reduce noise or overheating caused by a failing blower. What it does:

• Spins the blower wheel to circulate air through the appliance's airflow path
• Restores normal ventilation and heat distribution when the blower stops working
• Reduces rattling, grinding, or whistling noises from a worn motor or fan
• Helps prevent overheating or poor performance caused by restricted or non-moving airflow

• One blower and motor assembly as shown

• Disconnect all power before beginning service to avoid shock or injury
• Handle the assembly carefully to avoid bending the blower wheel or damaging wiring
• Basic hand tools typically required; follow appliance service manual for disassembly steps

This blower assembly replaces the oven/range blower motor and fan wheel to restore proper air movement and cooling. It keeps internal components ventilated for consistent performance and helps prevent overheating. What it does:

• Circulates air through the appliance to support heating and cooling functions
• Removes heat from control and electronic components to reduce thermal stress
• Restores airflow when a worn or failed blower causes poor venting
• Can reduce noisy operation caused by a damaged fan wheel or motor bearing

• Disconnect power to the appliance before beginning any service
• Handle the motor and fan wheel carefully to avoid damaging the fan blades or wiring
• After installation, reconnect power and run a short test cycle to confirm proper airflow and quiet operation