Gibson Refrigerator Gasket & Seal

The Refrigerator Door Gasket is an OEM part for Frigidaire refrigerators, designed to seal the door of the refrigerator compartment, ensuring an airtight closure. This door gasket plays a crucial role in maintaining the efficiency of the refrigerator by preventing cold air from escaping and warm air from entering.

Common causes for a Refrigerator Door Gasket to fail include normal wear and tear from opening and closing the door, damage from cleaning or misuse, and aging of the material, which can lead to hardening and loss of elasticity.

Symptoms of a bad Refrigerator Door Gasket include:

• Noticeable gaps or tears in the gasket
• The refrigerator door does not close as tightly as it should, or it requires more force to close.
• Condensation or frost buildup around the door edges
• An increase in energy consumption

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

The Refrigerator Door Gasket is an OEM replacement part for Frigidaire refrigerators. This gasket forms a tight seal around the refrigerator door, keeping cold air inside and preventing warm air from entering. By maintaining an airtight seal, it helps ensure consistent cooling and energy efficiency, preserving food quality.

Over time, gaskets can wear out due to frequent use, temperature changes, or exposure to cleaning chemicals. A damaged or degraded gasket can lose its flexibility or develop cracks, leading to an improper seal that affects the refrigerator's performance.

Symptoms of a bad refrigerator door gasket include:

• Warm spots or uneven cooling inside the refrigerator
• Excess condensation or moisture around the door
• Difficulty in securely closing the refrigerator door
• Increased energy consumption as the appliance works harder to maintain temperatures

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Freezer Door Gasket is an OEM replacement part for Frigidaire refrigerators. This gasket provides a secure seal around the freezer door, ensuring that cold air remains inside while keeping warm air out. It helps maintain consistent freezer temperatures for optimal food storage and prevents energy loss.

Causes of a bad freezer door gasket can include wear from regular use, exposure to temperature fluctuations, or damage from cleaning agents. Over time, the gasket may lose its flexibility, develop cracks, or become misaligned, compromising its ability to seal properly.

Symptoms of a bad gasket include:

• Frost buildup or ice accumulation inside the freezer
• Difficulty keeping the freezer door closed securely
• Warm air entering the freezer, leading to inconsistent temperatures
• Higher energy bills due to the freezer working harder to maintain cold temperatures

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Freezer Door Gasket is an OEM part for Frigidaire freezers. This part creates a seal around the freezer door to prevent warm air from entering and cold air from escaping, ensuring the freezer maintains its optimal freezing temperature. The gasket is made from a durable rubber material designed to conform tightly against the freezer frame when the door is closed. 

Over time, freezer door gaskets can wear out, become brittle, or lose their elasticity, leading to gaps and leaks in the seal.  

Symptoms of a bad Freezer Door Gasket include:

• Visible cracks or tears in the gasket
• Condensation or frost buildup around the door edges
• The freezer runs more frequently or for longer periods
• Difficulty in maintaining the set freezer temperature
• Increased energy bills due to the freezer working harder

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Fresh Food Door Gasket is an OEM replacement part for Frigidaire refrigerators. This component forms a critical seal between the refrigerator door and cabinet, helping to maintain the desired temperature and prevent cool air from escaping.

Symptoms of a failing fresh food door gasket may include:

• Difficulty closing the refrigerator door properly
• Warm air entering the fresh food compartment
•  Increased energy consumption due to loss of cooling efficiency

Causes of needing to replace the fresh food door gasket can include normal wear and tear over time, physical damage or tears in the gasket material, or improper door alignment preventing a tight seal.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore refrigerator models. 

The Refrigerator Gasket is an OEM replacement part for Frigidaire models. It provides a sealing barrier around the door frame, preserving cool air inside the refrigerator compartment. Composed of durable synthetic materials, the contoured gasket creates an insulating shield.

Causes of a faulty gasket include cracks or breaks from over-closure of the refrigerator door. Deterioration from extended exposure to temperature extremes can also impact integrity over time.

Symptoms of a bad refrigerator gasket include: 

• Inability to maintain a consistent internal cooling temperature
• Accumulation of moisture or frost at door edges  
• Visible gaps allowing warm external air to infiltrate
• Air leaks around the refrigerator opening

Compatible models include brands produced by Electrolux, Gibson, and Kelvinator.

The Gasket, Fresh Food Door is an OEM part for Frigidaire refrigerators. It is essential for creating a tight seal around the door of the refrigerator's fresh food compartment, preventing warm air from entering and cold air from escaping. This seal helps maintain the internal temperature, ensuring food stays fresh longer and the refrigerator operates efficiently. The gasket measures approximately 37 inches in length and 29 inches in width. 

Symptoms of a bad Fresh Food Door Gasket include:

• Condensation or frost buildup inside the refrigerator,
• The refrigerator running more frequently or for longer periods,
• Difficulty maintaining consistent temperatures in the fresh food compartment.

Causes of gasket failure can include normal wear and tear, exposure to harsh cleaning chemicals that degrade the material, or damage from frequent use.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This door gasket seals the perimeter of the appliance door to keep cold air in and humid air out. Replace a torn, warped, or leaky gasket to restore stable temperatures, reduce frost/condensation, and help the unit run efficiently. What it does:

• Creates an airtight seal between the door and cabinet
• Helps maintain proper temperature and humidity inside the compartment
• Reduces frost buildup and condensation around the door opening
• Common failure signs: tears, gaps, warping, hard or cracked rubber, door not closing flush, warm spots

• 1 door gasket

• Unplug the appliance and clear items from the affected door.
• Condition the new gasket to remove shipping kinks by laying it flat and warming it (soak in warm water or use gentle, low heat).
• Remove the old gasket; on some models you may need to loosen liner-retainer screws to release it.
• Fit the new gasket into the channel, working from the corners; ensure it seats evenly all around and verify a uniform seal.

This refrigerator door gasket forms an airtight seal between the door and cabinet to keep cold air in and moisture out. Replacing a worn gasket restores proper temperatures, reduces frost and condensation, and helps the unit run more efficiently.

• Creates a tight perimeter seal to prevent air leaks
• Helps maintain consistent internal temperatures
• Reduces moisture and frost buildup around the door
• Common symptoms of failure: tears or warping, visible gaps, door not sealing fully, temperature fluctuations, excess run time, or condensation at the door edge

• Disconnect power before service.
• Warm the new gasket in hot water or with low heat to relax kinks; avoid overheating.
• Remove the old gasket; install the new one by seating corners first, then work evenly around. For screw-retained styles, loosen and retighten fasteners evenly.
• Verify an even seal all around; adjust door alignment/leveling if needed and use a paper-slip test to check sealing.

This freezer door gasket creates a tight seal around the door to keep cold air in and humid air out—helping maintain set temperatures, reduce frost buildup, and support efficient, reliable freezer performance. What it does:

• Seals the freezer door perimeter to prevent air leaks and warm air infiltration
• Helps maintain consistent freezer temperature and energy efficiency
• Helps reduce frost/ice buildup and condensation around the door
• A worn, torn, or warped gasket can lead to poor sealing, frost, moisture, or longer run times

• 1 freezer door gasket

• Disconnect power before servicing
• Allow the new gasket to warm and relax (room temperature or warm water) for easier installation; do not overheat
• Remove the old gasket; clean and dry the door channel, then press the new gasket fully into place, starting at the corners
• After installation, check for uniform contact all around; adjust the door/hinges if needed and verify with a paper-slip test

The Freezer Door Gasket is an OEM part for Frigidaire freezers. It is designed to create a secure seal around the perimeter of the freezer door, preventing cold air from escaping and warm air from entering. This seal is crucial for maintaining the freezer's efficiency and effectiveness in preserving food at optimal temperatures. It measures approximately 17-1/4 inches in height and 26-1/2 inches in width.

Symptoms of a bad Freezer Door Gasket include:

• Visible gaps or tears in the gasket,
• Condensation or ice buildup around the door area,
• The freezer struggling to maintain the set temperature,
• Increased energy consumption as the freezer works harder to compensate for air leaks.

Causes of gasket failure typically include normal wear and tear, exposure to extreme temperatures that can cause the material to harden and lose elasticity, or accidental damage from cleaning or use.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Water Filter O-ring is an OEM replacement part for Frigidaire refrigerators. It is specifically designed to create a secure seal for the water filter, preventing leaks and ensuring that the filtration system operates effectively.

Causes for a malfunctioning Water Filter O-ring can include wear and tear from regular use, improper installation that leads to damage, or material degradation that affects its sealing capability.

Symptoms of a bad Water Filter O-ring include:

• Water leaks around the filter area
• Reduced effectiveness in water filtration
• The need for frequent filter replacements due to compromised seals
• Visible damage or wear to the O-ring

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This door gasket creates an airtight seal around your refrigerator or freezer door or lid, keeping cold air in and moisture out. Replace a worn gasket to restore temperature control, reduce frost, and support efficient operation.

• Forms a tight perimeter seal between the cabinet and door/lid to prevent air leaks
• Helps maintain stable internal temperatures and consistent cooling performance
• Reduces frost and condensation caused by a failed or leaking seal
• Common symptoms: visible tears or cracks, gaps, warping/shrinkage, door not sealing or staying closed

• Disconnect power; remove items from the door/lid as needed
• Warm the new gasket (soak in warm water or gently heat) to make it pliable, then straighten corners
• Fit the gasket into the channel or under the retainer, working evenly around the perimeter
• Check closure all around with a paper test; adjust hinges/leveling as needed and allow the gasket to relax and conform

This refrigerator seal restores a tight barrier between internal components. Replacing a worn or damaged seal helps prevent air leaks and moisture intrusion, supporting proper airflow, stable temperatures, and reduced frost or condensation around the joint.

• Creates an air-tight barrier between mating surfaces
• Helps maintain correct airflow and temperature balance between compartments
• Reduces frost, condensation, and warm/cold spots near the sealed area
• Common signs of failure: visible gaps, loose/crumbled seal, rattling panel, moisture or frost at the joint

• Disconnect power before servicing
• Remove the related cover or housing to access the old seal
• Clean contact surfaces; install the new seal in the same orientation without stretching or pinching
• Reassemble and verify an even seal and normal airflow before returning to service

This seal kit replaces worn sealing material in your appliance to restore a tight, reliable barrier. A fresh seal helps stop leaks and drafts, reduces noise, and supports proper temperature and moisture control.

• Creates a secure seal between mating surfaces or components
• Helps prevent air or water leaks around the sealed area
• Can reduce vibration noise from gaps or loose fits
• Supports stable temperatures and overall efficiency
• Common signs include visible gaps, cracking, flattening, or persistent leakage

• Disconnect power (and water or gas, if applicable) before servicing
• Remove the old seal and thoroughly clean mating surfaces of residue
• Test-fit for length/orientation; trim only if instructed by the manufacturer
• Press into place evenly; if adhesive-backed or cement is used, allow proper set time before use and check for leaks

Thermal mastic is a heat-conductive compound that improves thermal contact between temperature sensors/thermostats and appliance surfaces, helping sensors read more accurately for more consistent cooling and defrost performance. What it does:

• Creates a thermal bridge between sensors or thermostats and the surface they monitor to improve temperature sensing accuracy.
• Helps reduce symptoms caused by poor sensor contact, such as inaccurate temperature readings, intermittent cooling, or erratic defrost cycles.
• Applies as a thin, conforming layer to fill gaps and improve heat transfer without changing sensor placement.

• Disconnect power to the appliance before service.
• Clean and dry mating surfaces before applying a thin, even layer of mastic.
• Press the sensor or thermostat into the mastic so it contacts the surface; wipe away any excess.
• Avoid contact with eyes/skin, keep away from food-contact surfaces, and follow all OEM safety instructions.