Gibson Trim

The Rear Shelf Trim is an OEM part for Frigidaire refrigerators. It is designed to fit along the back edge of refrigerator shelves, providing a clean, finished look and helping to prevent items from sliding off the back of the shelf. 

Symptoms of a bad Rear Shelf Trim include:

• The trim becoming loose or detaching from the shelf, which can cause items to fall off more easily.
• Cracking or breaking of the trim, which may compromise the structural integrity of the shelf.
• Wear and discoloration that diminishes the aesthetic appearance of the refrigerator interior.

Causes of a bad rear shelf trim can include frequent removal or adjustment of shelves during cleaning or reorganization, physical impacts from storing or removing items, or the natural aging process that can make plastic components brittle over time.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Rear Shelf Trim is an OEM replacement part for Frigidaire side-by-side refrigerators. Located at the rear of the top shelf inside the refrigerator compartment, the trim piece defines the edge and provides a finished appearance. The trim measures approximately 22”.

Symptoms of a bad rear shelf trim can include:

• Cracks, chips, or scratches compromising its preserved shelf edge
• Discoloration, fading, or peeling ruining its matching polished finish  
• Sharp corners or splinters posing a potential pinch risk to users

Causes may be due to normal wear from cleaning agents, repeated drying cycles over time, or impacts stressing the trim's fragile plastic surface. 

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore side-by-side models.

The Front Shelf Trim is an OEM replacement part for Frigidaire refrigerators. Contained within the fresh food compartment, it secures the upper glass shelf and frames the front opening.

Causes relate to cracking or breaking of the brittle plastic over continued use, exposure to sudden impacts, or stresses from excessive shelf loading.

Symptoms of a bad trim include:

• Gaps appearing along the front cover leaving the shelf unstable
• Crackling or popping noises from inadequate support of shelf weight
• Difficulty removing or replacing the shelf track for cleaning

It is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.

The Vent Trim is an OEM part for Frigidaire ranges. This part frames and supports the oven's ventilation system, ensuring proper heat dispersal and maintaining the aesthetic integration of the range within the kitchen setup.  

Common causes for vent trim issues include physical impacts during cleaning or use, thermal deformation from continuous exposure to high temperatures, and general wear and tear over time.  

Symptoms of failing Vent Trim include:

• Loose or ill-fitting trim that may not stay in place
• Visible damage such as cracks or warping due to heat exposure
• Increased heat retention or abnormal heat outside the oven
• Aesthetic discrepancies that impact the overall look of the kitchen

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This Door Trim Kit restores the finished look and proper fit around the door. It replaces damaged or missing trim that frames the door/panel, helping secure outer components and refresh the appliance's appearance.

• Provides a clean, finished edge around the door perimeter
• Helps retain/position the outer glass or panel on applicable designs
• Replaces cracked, warped, loose, or missing trim that may rattle or leave gaps
• Common symptoms: visible damage, looseness, gaps, or cosmetic wear around the door

• Disconnect power at the breaker or unplug the appliance before servicing
• Protect the work surface; wear cut-resistant gloves and handle glass carefully
• Note orientation and fastener locations; transfer any reusable clips/screws from the original assembly
• After reassembly, confirm smooth door operation and proper alignment/seal

This replacement surface burner cap sits on top of the gas burner head to focus and distribute the flame for even, efficient heating. Replacing a damaged or missing cap can restore proper ignition and flame pattern. What it does:

• Covers and protects the burner head from spills and debris
• Spreads and concentrates the flame for consistent cooking performance
• Helps prevent yellow, lifting, or uneven flames when properly seated
• Common symptoms: uneven or yellow flames, poor simmer, delayed ignition, chipped/warped/missing cap

• 1 surface burner cap

• Allow the cooktop to cool; disconnect power and shut off gas if servicing beyond simple cap replacement
• Lift off the old cap and clean the burner head surface of residue or debris
• Center the new cap on the matching burner head so it sits level—do not force
• Use the correct cap for the burner position; test ignition and flame after installation