Gibson Relay, Overload, Capacitor

The Compressor Run Capacitor is an OEM replacement part for Frigidaire refrigerators. This electrical component is essential for providing the necessary torque to start and maintain the operation of the compressor motor, which is responsible for cooling the refrigerator.

Symptoms of a failing compressor run capacitor include:

• The refrigerator not running or cooling properly
• The compressor failing to start or running intermittently
• Humming or buzzing noises coming from the compressor area

Causes of needing to replace the compressor run capacitor can include normal wear over time, exposure to high temperatures or electrical surges, or physical damage to the capacitor itself.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore refrigerator models. 

The Compressor Start Kit is an OEM part for Frigidaire refrigerators. It is responsible for providing a reliable start-up for the compressor. It includes the necessary components to assist in initiating the compressor's motor, allowing it to run efficiently.

A bad compressor start kit can occur due to electrical issues, damage, or wear over time. If the start kit fails, it can lead to problems such as the compressor not starting, warm temperatures inside the refrigerator, or inconsistent cooling performance.

Symptoms of a bad compressor start kit include:

• Compressor not starting or struggling to start.
• Warm temperatures inside the refrigerator.
• Inconsistent cooling or inadequate cooling.
• Unusual noises coming from the compressor.

If you're experiencing any of these issues, it's time to replace the compressor start kit with this genuine part. Restore the proper functioning and cooling performance of your refrigerator with a new compressor start kit. This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

Capacitor-run,220 vac ,12 microfarad

The Compressor Start Device is an OEM part for Frigidaire refrigerators. It plays a critical role in initiating the compressor, which is essential for the cooling process. This device helps the compressor start smoothly and efficiently, ensuring your refrigerator maintains the desired temperature.

Causes of a bad compressor start device can include electrical issues, normal wear and tear over time, or damage due to power surges or voltage fluctuations.

Symptoms of a bad compressor start device include:

• The refrigerator not cooling properly
• Clicking noises coming from the back of the refrigerator
• The compressor not starting or running intermittently
• Overheating of the compressor

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This compressor start device briefly energizes the compressor's start winding to get it running, then disengages automatically. Replacing a weak or open PTC can restore cooling and stop the repeating hum-click from the compressor area.

• Provides the initial boost for the compressor to start, then opens as the PTC warms
• Helps the compressor start reliably on each cooling cycle
• Works with the compressor's overload protector to safeguard the motor circuit
• Common symptoms of failure: not cooling, compressor won't start, rapid clicking or hum-click every few minutes, intermittent cooling after power cycling

• Disconnect power and pull the unit forward to access the compressor compartment
• Remove the start-device cover; note wire positions
• Pull the old start device straight off the compressor terminals; avoid bending the pins
• Align the new device with the C–S–R terminals in the same orientation, push on fully, reconnect wires, reinstall cover, and restore power
• Inspect the mating overload protector and terminal connectors for heat damage before reassembly

This controller kit is the electronic oven control module that governs bake, broil, and temperature functions. Replacing a failing control restores accurate oven operation and responsive keypad/display performance.

• Regulates oven heating cycles and temperature feedback from the sensor
• Controls bake/broil relays and user interface responses
• Common failure symptoms: no bake/broil, temperature inaccuracy, unresponsive buttons, blank or erroring display
• May recover from intermittent power-up, beeping, or F-codes tied to the control

• Disconnect power before servicing; high voltage is present
• Handle the board by edges; avoid static discharge to components
• Transfer all wiring one connector at a time to the matching locations
• After installation, restore power and verify oven operation and temperature calibration

The Starter is an OEM replacement part for Frigidaire refrigerators. This component is crucial for initiating the compressor, which is responsible for cooling the refrigerator. The starter works by providing the necessary electrical power to get the compressor running, ensuring that the refrigerator maintains the correct temperature.

Causes of a bad starter can include electrical malfunctions, wear and tear over time, or damage from power surges. A faulty starter can prevent the compressor from starting, leading to cooling issues.

Symptoms of a bad Starter include:

• The refrigerator not cooling properly
• The compressor not running or frequently cycling on and off
• Unusual clicking or buzzing noises from the compressor area
• The refrigerator being warmer than usual or food spoiling quickly

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This controller kit replaces the appliance's electronic control board, restoring proper power-up, keypad/display response, and reliable operation of controlled functions. Use it to address unresponsive controls or erratic behavior caused by a failed control board. What it does:

• Manages operation of key components based on sensor inputs and user settings
• Processes keypad/remote commands and powers display, mode, and timer circuits
• Coordinates temperature feedback to maintain selected settings
• Common failure symptoms include no display, unresponsive buttons, will not start, intermittent cycling, or error codes

• One controller kit

• Disconnect power before servicing; allow capacitors to discharge
• Use ESD precautions; handle the board by the edges only
• Access the control compartment; photograph wiring and move connectors one at a time to the new board
• Securely mount the board, restore power, and test all functions

This compressor start device kit helps your refrigerator or freezer's compressor start reliably each cooling cycle. Replacing a weak or failed start device can restore cooling performance and stop repetitive clicking or brief humming when the compressor tries to start.

• Powers the compressor's start winding to initiate start-up, then disengages
• Supports consistent compressor starts to maintain proper temperatures
• Common symptoms of failure: unit warm, compressor not running, rapid clicking from rear, humming then shuts off
• May accompany signs like heat damage or a burnt odor at the old device

• Unplug the appliance before servicing; allow components to cool
• Located on the side of the compressor behind the rear access panel
• Photograph wiring and compressor pin layout; transfer wires one at a time and seat the device fully on the pins
• If your unit uses a separate run capacitor, reconnect it exactly as originally wired

This controller kit is the appliance's main electronic control. It reads inputs from the user interface and sensors to power and coordinate key components. Replacing a failed controller restores responsive controls and consistent, reliable operation.

• Interprets commands from the keypad and sensors to manage operation
• Controls relays powering motors, fans, compressor, or valves as designed
• Coordinates modes and cycle timing for proper performance
• Common symptoms: dead or blank display, unresponsive buttons, won't start, intermittent shutdowns, or error codes

• Disconnect power at the breaker or unplug the appliance before servicing
• Handle the board with ESD precautions; avoid touching connectors and components
• Photograph/label wire connections and transfer them one at a time to the new board
• After installation, verify any model-specific settings per the service documentation before testing

This PTC compressor start relay briefly powers the compressor's start winding to get the motor turning, then drops out as it warms. Replacing a weak relay can restore consistent compressor starts and stabilize refrigerator and freezer temperatures.

• Momentarily energizes the compressor's start winding; disengages automatically as the PTC element heats
• Helps protect the compressor by removing the start winding after startup
• Symptoms of failure can include compressor clicking but not running
• Intermittent cooling or warming temperatures between cycles
• Heat discoloration or a burnt odor around the start device

• Disconnect power and remove the rear lower access panel
• Note wire locations; remove the start device cover/retainer and pull the old relay straight off the compressor pins
• Inspect compressor pins; firmly seat the new relay and reconnect wiring
• Reinstall covers/panels, restore power, and verify normal compressor start

This electronic control board manages the appliance's user interface and core control functions, restoring reliable operation when the original board fails. It replaces a damaged or unresponsive control module to help regain normal appliance control. What it does:

• Sends and receives signals to operate timers, relays, and display functions.
• Controls user inputs and on/off sequencing for the appliance's systems.
• Common symptoms of a failing board: unresponsive controls, blank or erratic display, cycles not starting or stopping, or intermittent operation.
• Use this board to replace units exhibiting control or display faults that other components have not resolved.

• Disconnect power at the breaker or unplug the appliance before starting any repair.
• Handle the board by the edges and avoid touching components; use an ESD strap if available.
• Verify wiring harness connections and fuses before and after installation.

This relay assembly helps start the refrigerator compressor so the cooling system can run reliably. It replaces a worn or failed start relay to restore normal compressor startup and reduce hard-start symptoms. What it does:

• Provides the initial start pulse to the compressor motor so the refrigeration cycle can begin
• Stops excessive current draw during startup to protect the compressor
• Commonly used when the compressor hums, won't start, or cycles on and off rapidly
• Helps eliminate starter-related clicking or failure-to-start issues

• Disconnect power to the appliance before inspecting or replacing the relay
• Handle electrical connectors carefully; ensure secure, correct reattachment
• Verify match to the existing relay and mounting before installation

This PTC starter helps the compressor start by briefly supplying the correct current at startup, restoring reliable cooling when the compressor struggles to kick on. Compact replacement for failed or weak start devices. What it does

• Provides a timed boost to the compressor start winding so the compressor can start reliably
• Commonly used when a refrigerator or freezer won't start or hums without running
• Helps prevent frequent hard starts that can overheat the compressor
• Passive solid-state design with no moving parts for simple, maintenance-free operation

• Disconnect power to the appliance before inspecting or replacing the starter
• Handle electrical connections carefully; install the starter in the same orientation and wiring position as the original
• If the compressor or start relay shows additional damage, replace those components.

This compressor start relay helps the refrigerator compressor start reliably so the appliance can maintain proper cooling. It replaces a failing start device to restore normal compressor startup behavior. What it does:

• Provides the initial boost to the compressor motor so it can start turning
• Commonly used when the compressor hums or won't start but power is present
• Can reduce repeated clicking or intermittent starts caused by a failed start device
• Works with the compressor's start circuit; does not replace sealed-system components

• One compressor start relay

• Disconnect power to the appliance before accessing electrical components
• Inspect associated start capacitor/overload if present; replace if faulty for reliable operation

This capacitor stores and releases electrical energy to help the refrigerator's compressor start and run smoothly. Replacing a weak or failed capacitor can restore reliable compressor startup and more consistent cooling performance.

• Provides the electrical boost/phase shift needed for compressor motor startup and steady operation
• Works with the start device to deliver proper current to the compressor
• Failure symptoms can include clicking or humming near the compressor, poor cooling, or short cycling
• May cause the compressor not to start after power interruptions when weak or failed

• Disconnect power before servicing any electrical component
• Safely discharge the capacitor before handling; avoid touching terminals
• Note wire positions and terminal markings; transfer leads one at a time to the matching terminals
• Secure the capacitor in its mounting/bracket to prevent vibration damage