Gibson Washer Dryer Combo Switch
Genuine Frigidaire part
By: Frigidaire
Part Number: 134399700
The Start Switch is an OEM replacement part for Frigidaire dryers. This part initiates the dryer's cycle once the user selects the desired settings. By pressing the start switch, the motor activates, and the drying process begins, ensuring clothes are dried according to the selected specifications.
Symptoms of a bad Start Switch include:
- The dryer not starting when the switch is pressed
- Intermittent starting issues, where the dryer sometimes starts and sometimes doesn’t
- The need to hold the switch in place to keep the dryer running
- Unusual noises when the switch is pressed
Causes for a malfunctioning Start Switch can include electrical issues, such as faulty wiring or connections, wear and tear from frequent use, or internal failures within the switch mechanism that prevent it from signaling the motor to start.
This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore dryers.
Do-It-Yourself Stories from Customers like You
Start switch knob broke off. Jeff O. • Laurier , WA • March 07, 2018
I went online, ordered the part and installed it,,, took 15 minutes to install,,,saved huge $$$
easy peasy!! :-)
Read more
More
$64.95
- Compare At:
-
$77.29
- You Save:
-
$12.34
Genuine Frigidaire part
By: Frigidaire
Part Number: 134422700
This is a factory switch used in the appliance's control/safety circuit. Replacing a worn or failed switch restores reliable signaling so the selected function engages properly and the unit responds consistently to user inputs and status conditions.
- Provides an electrical on/off signal to the control or safety circuit
- If faulty, selected functions may not activate or may be intermittent
- Can trigger error codes related to a switch input, depending on model
What's included: 1 switch Install notes:
- Disconnect power before servicing; turn off gas/water if applicable
- Note/photograph wire locations and transfer connectors one at a time
- Verify actuator alignment and secure mounting before reassembly
- After installation, run a test cycle to confirm proper operation
This part fixes the following symptoms
-
Will not stop filling with water
See more...
Do-It-Yourself Stories from Customers like You
The stem of the original switch had been twisted off Benjamin R. • Seattle , WA • April 15, 2019
I removed two sheet metal screws to remove the panel above the washing machine lid. That exposed four more phillips drive sheet metal screws, after removing those the dashboard control panel is held by two smaller black screws slightly recessed in the lower corners. This allowed the panel to be pulled down from the top, revealing the back of the switch. At this point I took a picture of the wiring connections with my cell phone to make sure I put them on the new switch in the same...
Read more
More
$76.95
- Compare At:
-
$91.57
- You Save:
-
$14.62
Genuine Frigidaire part
By: Frigidaire
Part Number: 134493500
$154.95
- Compare At:
-
$184.39
- You Save:
-
$29.44
Out Of Stock
Usually ships within 4 - 14 days
Genuine Frigidaire part
By: Frigidaire
Part Number: 134446800
Do-It-Yourself Stories from Customers like You
Dryer timer would not advance in automatic dry mode worked fine in timed mode Michael S. • Bear , DE • February 05, 2016
Replaced the power resistor on the timer assembly. Solved the problem.
Read more
More
Genuine Frigidaire part
By: Frigidaire
Part Number: 131628900
This push start switch is the user-operated momentary button that completes the start circuit so the appliance begins its cycle. It replaces a worn or unresponsive start button to restore reliable start control. What it does:
- Acts as a momentary contact to send the start signal to the control
- Commonly used when the appliance does not begin a cycle after pressing the start button
- Can fail from wear, corrosion, or broken actuator, causing no response or intermittent starts
- Works with the factory wiring and mounting for direct replacement
What's included:
Install notes:
- Always disconnect power to the appliance before performing service
- Handle terminals carefully; ensure secure, corrosion-free connections
- Test the switch for continuity with a meter after installation and before restoring full use
Do-It-Yourself Stories from Customers like You
The start button did not start the dryer Fr. Milad S. • Worcester , MA • April 07, 2015
We replaced the start button
Read more
More
Gibson washer dryer combo switch replacement parts are essential for keeping your machine running smoothly and efficiently. Whether you're tackling a mountain of laundry or just need to freshen up a few items, having a reliable washer dryer combo is a game-changer. That's where the quality and availability of Gibson washer dryer combo switch parts come into play.
Gibson washer dryer combo parts, including top-notch switches, ensure that your machine continues to function at its best. These components are designed to offer seamless integration with your appliance, guaranteeing that every wash and dry cycle is completed effortlessly. Opting for OEM replacement parts gives you peace of mind, knowing that these switches are specifically crafted to fit and perform perfectly within your Gibson washer dryer combo. OEM parts highlight the importance of compatibility and durability, often outperforming generic alternatives.
When you need to replace a switch, rest assured that high-quality Gibson washer dryer combo switch parts are readily available. Keeping your appliance in prime condition has never been easier, ensuring that you can depend on its performance for years to come. So, the next time your washer dryer combo needs a bit of attention, you know that reliable replacement parts are just a step away.
More