Huskee / Husky Lawn Mower Parts

This recoil spring and pulley assembly is used in a variety of small gasoline engines that power devices such as mowers, lawn tractors, and log splitters, among other yard and landscaping devices. The assembly works by tightly coiling the spring in the starter housing. When the starter rope is pulled, the tension on the spring is suddenly released, creating a spark that fires the air/fuel mixture. The combustion starts the engine. The constant tightening and releasing of the tension at times will cause wear on the spring, resulting in the need to replace the spring and pulley assembly. To replace the recoil starter assembly, begin by removing the housing. Next, untie or starter rope and check to see if it is frayed and needs to be replaced as well. Remove the old assembly and install the new unit. Remember when re-tensioning the spring to wind the pulley in the opposite direction. Holding the pulley tightly so the spring does not release, attach the cap. Reattach the rope and coil it around the pulley. It is advisable to wear gloves for this task because the pulley and springs have sharp edges. This OEM certified replacement assembly is compatible with Yard-Man, Husky, Cub Cadet, MTD, Yard Machines, and Troy-Bilt yard equipment.

The primer bulb is a small plastic piece that will draw fuel from the fuel reservoir and into the carburetor when it is pressed down. This ensures that the fuel can get into the carburetor so that combustion can happen in the engine. If the primer bulb is broken or damaged on the engine, it will mean that the carburetor will not be getting the fuel it needs to get the engine to start. In some cases, the engine might not start at all. Other times, it might take a while to get the engine to start. These could indicate that it is time to replace the bulb. This is an OEM replacement part that is sold individually. It will work with lawnmowers and other types of small engines. The bulb is compatible with a range of different popular brands including Toro, Kawasaki, Cub Cadet, MTD, and Craftsman.

Fuel filters are created to strain out gas before it reaches the carburetor in lawnmowers and other gardening tools. Located in the fuel line or the fuel tank, it prevents unwanted debris from reaching the carburetor, which can cause engine damage. If the fuel filter is damaged or becomes clogged with material, it no longer offers the same protection to the carburetor. This can lead to difficulty starting the lawnmower and decreased performance. Correcting this issue early can prevent damage that might require a new lawnmower. Maintenance of the lawnmower by adding fuel stabilizer, changing the oil, and replacing the air filter will increase the life of lawn care equioment. Even if no issues are present, the fuel filter should be replaced after about 200 hours of use. Disconnecting the spark plug should be done prior to installing a new fuel filter. This fuel filter is a genuine OEM component directly from the manufacturer and comes as an individual part. It can be used with various Craftsman, Cub Cadet, Murray, Yard Machines, MTD, Huskee, Bolens, Yard-Man, and Mastercut lawnmowers, tillers, blowers, and wood chippers.

This is a recoil starter assembly for lawn and garden power equipment. When the recoil starter rope is pulled, this causes the spark which starts the engine.A new recoil starter assembly will be needed if the recoil or pulley system has broken. The rope may become broken or frayed and the plastic on the pulley could crack. If the rope becomes loose and there is no tension when it is pulled, then a new recoil starter assembly will be needed.This part is a genuine MTD part and is an OEM part sourced directly from the manufacturer and it is sold individually. It is used on engines, lawnmowers, lawn tractors, and log splitters that are manufactured by MTD, Yard-Man, Yard Machines, Cub Cadet, Husky, and Troy-Bilt.

This part is a replacement breather valve. This is a genuine OEM part made by MTD and has been sourced directly from the manufacturer. This part can be used to replace a broken, lost, or defective breather valve in a variety of outdoor power equipment models.Breather valves are essential for keeping the engine in proper working order. They can easily become lost, worn, or otherwise rendered ineffective and thus should be replaced with a genuine OEM part. When working on or near any mechanical equipment, it is important to verify that it is powered off and completely cooled down before starting any repairs. For more accurate information on how and where to install this part, the appropriate owner's manual and equipment diagrams should be referred to. As an authentic replacement part, this breather valve is suitable for use on several different models of outdoor power equipment models manufactured by MTD, Craftsman, and other brands. This is a genuine part made of high-quality, durable materials and is sold individually.

This is a starter recoil assembly. It is used when starting small lawn equipment and other machines. It engages the flywheel. With time and use, any or all of the recoil can wear out or become damaged, including the spring, housing, rope, or pulley. If something is damaged or worn out, the entire starter recoil assembly must be replaced. Signs that the part requires a repair include an engine that won't start or has difficulty engaging.Replacing a starter recoil assembly is easy and can be done in about 15 minutes. A nut driver and screwdriver are required for the repair. Wear gloves. Make sure the equipment is completely cooled before beginning the recoil assembly replacement. After putting tension on the spring and pulley, hold the housing securely to prevent it from releasing.The starter recoil assembly is a genuine OEM-authorized replacement part. It is sold individually. The starter recoil assembly is compatible with MTD, Cub Cadet, Yard Machines, Husky, Yard-Man, and Troy-Bilt brands. It is a complete part that includes the housing, rope, pulley, and recoil spring. It works with small engines, lawnmowers, log splitters, trimmers, and other similar equipment.

This genuine OEM Part is a choke temperature control rod for lawnmowers. The choke temperature control is the metal piece that regulates the choke temperature allowing for it to function properly within a lawnmower. If the choke function is no longer working efficiently, it might be time to replace the choke temperature control. Luckily, replacing this part is a simple repair.Before beginning, make sure the engine is cool to avoid getting burned. Locate the old choke temperature control rod and remove the screws to the mounting assembly that hold the rod in place. Once removed, lift the old choke temperature control out and away from the mower and set it to the side. Replace with the new control rod and secure the mounting screws. Start up the mower to see if the choke function is working properly. If it does, the installation was a success. This replacement part is sold individually and is compatible with MTD brand lawnmowers.

This is a replacement pre-filter. This is a genuine OEM part made by MTD and has been sourced directly from the manufacturer. This part can be used to replace a worn or defective pre-filter on a variety of different models of power equipment.Pre-filters help to keep larger particles of debris from entering the filter itself, preventing clogging and damage. The pre-filter will need to be cleaned and changed with regularity to ensure proper equipment function. It is always recommended that the appropriate safety precautions are adhered to when attempting to fix any power tools or machinery. For more accurate information on how and where to install this pre-filter, refer to the appropriate owner's manual and included diagrams.As an authentic replacement part, this pre-filter is suitable for use on several different lawnmower models and small engine power equipment manufactured by MTD, Troy-Bilt, Husky, and Yard Machines. This is a genuine part made of high-quality, durable foam material and is sold individually.

This replacement part is an air filter, and it is intended for use in different types of lawn equipment. This is a genuine replacement part made by MTD. This air filter is typically found in riding lawn mowers and is responsible for filtering out air from the engine. This air filter is able to catch dust and debris so that the engine of the lawn mower is kept in proper working order. A new air filter might be needed if the current one is full of debris or is visibly clogged. It is recommended that the air filter be replaced once per season or after about 300 hours of use. If the user notices that the air filter is dusty, it is recommended it be cleaned. This air filter is a genuine OEM replacement part sourced directly from the manufacturer and is sold individually. Be sure the engine is powered down before replacing this part.

This is an air filter that can be used with lawn and garden equipment. The air filter plays an important role in mowers, trimmers, and more. It prevents airborne contaminants like dirt, dust, leaves, and other debris from getting pulled into the engine. Air filters should be checked regularly and replaced when they become dirty, or if they are punctured or otherwise damaged. This is a quick repair that should take only a few minutes to complete.The air filter will work with lawn mowers and trimmers from MTD, Yard-Man, Troy-Bilt, Yard Machines, and Cub Cadet. The piece is sold individually. It is a genuine OEM replacement part that has been sourced from the manufacturer.

The height adjustment assembly is a replacement part that is designed for use in select walk-behind lawn mowers. The adjustment assembly includes nine total height adjustments and installs on the front wheel of the unit to allow the user to adjust the wheel height and cutting height before each use. The metal height adjustment assembly is exposed to constant impacts and repetitive motion, which can lead to damage or wear. If the height adjustment fails, the mower may be inoperable until the part is replaced. This genuine OEM part will provide the appropriate replacement for select models from MTD, as well as those from Troy-Bilt, Bolens, Yard Machines, Yard Man, Husky, and Cub Cadet. It is sold as an individual assembly and the hardware required will be sold separately. This is an identical replacement for the right side of the mower. It is important to wear gloves when working on the mower deck and allow the unit to cool completely for safety. The height adjuster will take a wrench or socket set and screwdrivers to install.

This replacement part is a height adjuster assembly, and it is intended for use in different types of lawn equipment. This is a genuine replacement part made by MTD. Height adjuster assemblies allow the user to adjust the height of the blades on a mower to change the length grass will be cut to. This device is essential so that the user can customize the job during each lawn cutting. A new height adjuster assembly might be needed if the user notices that the current one is no longer working. If the user is unable to adjust the height of the blades, it might be time to replace the height adjuster. Be sure to wear working gloves during this repair as this part is situated close to the blades of the lawn mower and can be dangerous if not properly protected. This height adjuster is sold individually. Note that it is also a genuine OEM replacement part and is sourced directly from the manufacturer.

This replacement part is an adjuster assembly intended for use in lawn mowers. This adjuster assembly allows the user to control the height of the mower's blades, which will adjust the depth of a cut.An adjuster assembly may become stripped or worn down over time, necessitating replacement.This is a genuine OEM replacement part manufactured by MTD. This part is sold individually.