Huskee / Husky Tiller Parts

Engine running rough or making ticking noises? A worn rocker arm stud can affect valve timing. This replacement stud restores proper valve operation.

Hex screw for outdoor power equipment. Replacement fastener for lost, stripped, or damaged screws. Installs in various assembly locations.

This hex screw and lock washer are commonly used with lawn mowers and other small engines to secure a motor to the housing of the equipment. It is machined in such a way that it binds the manifold and frame permanently. There are occasions when these bolts have to be removed, typically when major repairs are performed on the engine. In those cases, users often find it advisable to replace the hex bolts and washers with new ones. It happens as well that these screws are so tightly fastened that they cannot be unscrewed and must be cut off. In those cases, it is necessary to replace the original screws. These replacement screws and lock washers are genuine OEM certified replacements that are manufactured to be identical to the hardware they are replacing. In addition to mowers, these hex screws are used to secure engines to devices such as log splitters, edgers, shredders, trimmers, and snowblowers. This screw is compatible with devices made by Husky, Yard-Man, Cub Cadet, Troy-Bilt, Ryobi, Bolens, and Yard Machines.

This genuine OEM replacement jam nut attaches to the idler bracket on a tiller. Jam nuts are a special type of nut designed to not unthread or strip out over time. Jam nuts are usually fastened on with another standard nut and then the two nuts are tightened against each other. Jam nuts can be easily identified from a standard nut because they are roughly half the size. Jam nuts can be lost while making repairs because of their small size. If lost, it might not affect the idler bracket immediately, but over time the standard nut may begin to slip or unthread. Therefore, the jam nut should be replaced as soon as possible. When making this replacement, be sure to unthread the standard nut as well and then tighten them both together using a wrench. This replacement jam nut is a high-quality part sourced from its original manufacturer. It is compatible with Troy-Bilt, Yard Man, Huskee, MTD, Ryobi, Yard Machines, and Cub Cadet tillers. This part does not ship with any additional hardware.

Replacement shift rod knob for tillers and garden tractors. Installs on the shift rod for comfortable gear changes. Replace if cracked, broken, or missing.

Spacer for snow throwers and small engines. Fits over bolts or screws to maintain proper spacing between components. Replace if missing or damaged.

Bell washer for lawn mowers and tractors. Replaces cracked, worn, or missing washers in drive assemblies. Ensures proper spacing and load distribution.

This part is a spark plug that is used on a number of lawn and garden power equipment. A spark plug is used as part of an internal combustion engine. The spark plug delivers the electric current from the ignition system to the engine.A new spark plug may be needed after normal wear and tear over a period of time. The operator of the outdoor power equipment may notice that the engine misfires or it is difficult to start. If this is the case, a new spark plug will be needed. Never perform care and maintenance on outdoor power equipment that is powered on. Remember to wear gloves when operating or performing care and maintenance on any outdoor power equipment.This spark plug is a genuine MTD part. It is sold individually. This particular spark plug is compatible with various outdoor power equipment that are manufactured by MTD, Yard Machines, Troy-Bilt, Bolens, Yard-Man, and Cub Cadet.

Oil seal for tillers prevents fluid leaks from transmission or engine components. Replace if you notice oil pooling or leaking. Verify fit with model number.

Pull cord won't retract or seized up? This complete recoil starter assembly includes housing, pulley, spring, rope and grip. Bolts on in minutes.

Fuel line kit for small engines. Carries fuel through the machine. Replace if cracked, leaking, or ends don't fit securely even when clamped down.

Air cleaner filter prevents dirt and debris from damaging your mower engine. Replace when thin, damaged, or dirty to maintain performance. Verify fit.

Left hand inner tines assembly for tillers. Installs next to outer tines on the left side. Replace if tines are worn, bent, or broken from soil cultivation work.

Outer tine assembly for tillers, left-hand configuration. Installs on tine shaft for soil cultivation. Replace if bent, cracked, or worn from impact.

Tiller won't break up soil or leaves clumps? This tine assembly loosens packed soil for proper planting. Sold individually, moderate DIY install.

This is an idler pulley assembly for a snowblower or tiller. The idler pulley works together with other pulleys to drive the belt system in an engine. It regulates the belts connecting to the crankshaft to produce movement in various engine accessories. This is a genuine OEM part and is sold individually. This part is compatible with Craftsman, Cub Cadet, Huskee, Troy-Bilt, and Yard Machines. Over time, the pulley components wear down and begin to slip. Damaged bearing devices can also cause wear on the pulley, causing the engine to fail. To replace an idler pulley in a snowblower, remove the ignition key and disconnect the spark plug. Using a socket wrench, remove the mounting bolts securing the belt cover. If required, loosen the tension. Use a ?-inch socket to remove the lower bolts. Pull off the cover and use the wrench to remove the bolt from the pulley. Remove the old part and transfer the bushing into the new part. Position the new pulley, thread the bolt, and tighten. Per model, either realign the auger drive linkage on the bolt and slide on the push nut to secure, or realign and reset the tension spring. Then, recover and reattach.