Parts for Lg LFCC22426S/04: Ice Maker & Ice Bin Parts

The Handle Mounting Stud is an OEM replacement part for LG refrigerator doors. It provides a sturdy mounting point for the door handle assembly. Reliable handle connection and support is crucial for dependable door function and access. 

Causes of a faulty stud can include damage from excess weight or impact over time rendering the stud loose or unstable.

Symptoms of a bad stud include:

• Loose or sagging door handle  
• Difficulty opening and closing the refrigerator door  
• Potential for the handle to detach completely
• Safety concerns if the handle connection fails

This OEM LG replacement stud is also compatible with Sears/Kenmore models. 

The Drain Pipe Assembly is an OEM replacement part for LG refrigerators. It is a plastic tubing system that collects and removes liquid condensation from evaporator coils. Proper drainage is crucial to minimizing frost buildup and ensuring optimal cooling of food storage areas. 

Symptoms of a bad drain pipe assembly include:

• Excessive frost or ice accumulation inside the refrigerator
• Puddling or leaks detected near evaporator housing
• Slow draining allowing water to pool versus emptying fully
• Cracks or breaks in the tubing prevent complete fluid removal

Causes are typically mineral sediment clogging drainage paths or deteriorating plastic from constant use. This OEM LG replacement pipe restores reliable condensate removal to maintain peak efficiency.

This OEM LG part is also compatible with Sears/Kenmore. 

The Leveling Leg is an OEM part for LG refrigerators. It is one of the four legs at the bottom corners that elevate and provide stability to the entire appliance.

Causes of failure can be broken mounting points that no longer provide secure elevation, full compression of the built-in cushioning, or damage from impact on an unlevel floor.

Symptoms of a faulty leveling leg include:

• Excessive shaking or vibrating of the refrigerator
• Door alignment issues where doors are difficult to open or close fully
• Visible leaning or misalignment of the refrigerator cabinet

This OEM LG part is also compatible with some Kenmore models.

This is an ice storage bucket that collects and holds cubed ice from the refrigerator ice maker, making it easy to dispense and store ice for daily use. It replaces a cracked, warped, or missing ice bin to restore proper ice handling. What it does:

• Collects and stores ice produced by the ice maker so cubes are ready to dispense
• Guides ice to the dispenser/door chute or manual access area to prevent spills
• Prevents ice jamming caused by broken or deformed bins
• Helps keep ice contained and sanitary inside the freezer compartment

• Disconnect power before servicing the ice maker area to avoid injury
• Remove any remaining ice before removing the old bucket to reduce spills
• Align bucket tabs/guides and slide into place until it seats naturally; do not force
• If ice does not dispense after install, check ice maker alignment and clear ice chute

A small protective cap that covers and protects a component connection or opening from dirt and moisture, helping maintain proper function and prolong component life. Simple replacement when the original cap is cracked, missing, or worn. What it does:

• Covers exposed fittings, terminals, or openings to keep out debris and moisture
• Helps prevent leaks or contamination at the sealed connection
• Restores a secure fit when the original cap is cracked, split, or degraded
• Commonly used where a small, removable protective seal is required

• Inspect mating surface and surrounding gasket/seal before installing; replace other damaged parts as needed
• Press the cap firmly into place until fully seated; no special tools usually required
• Wear gloves and disconnect power or water supply if working near energized or pressurized components

This roller assembly supports and guides a sliding rack, shelf, or drawer so it rolls smoothly along its track. Replacing a worn roller restores easy, even movement and helps prevent sticking, wobbling, noise, or the rack/drawer jumping off the rail.

• Provides rolling support for a sliding component on its rail
• Maintains alignment to reduce binding and off-track jams
• Helps the rack/drawer glide quietly and evenly
• Common signs to replace: hard-to-slide movement, squeaking/grinding, wobble or tilt, or a cracked/missing wheel

• Disconnect power before servicing; shut off water supply if applicable to your appliance
• Remove the rack/drawer to access the roller; support moving parts while working
• Note roller orientation and re-use existing fasteners/clips as designed
• Replace both sides for even operation

The Freezer Tray Roller is an OEM part for LG refrigerators. It is a dual roller wheel assembly located at the rear wall of the freezer compartment. The roller aids sliding shelf movement by reducing friction between trays and the liner wall. 

Causes of a bad freezer tray roller include cracks, flat spots, or separated roller pieces from wear over years of use.

Symptoms of a bad tray roller are:

• Difficulty sliding shelves smoothly in and out of position
• Excessive force required to access stored items
• Noisy operation or rattling noises within the freezer

This genuine LG OEM replacement part is also compatible with some Kenmore models.

This tray assembly is the replacement drawer pan that supports and contains items inside the refrigerator drawer, restoring proper storage and a secure sliding surface for the drawer. It helps keep foods contained and prevents sagging or cracking. What it does

• Replaces a cracked, warped, or missing drawer tray to restore a stable surface for stored items
• Supports the refrigerator drawer so it opens and closes smoothly and stays aligned
• Helps contain spills and prevents food from falling onto lower compartments
• Fits into the existing drawer frame and works with original slides and seals

• Disconnect power to the appliance before starting any repairs
• Remove the drawer and slides per the refrigerator's service instructions before swapping the tray
• Handle plastic components carefully to avoid cracking; use gentle pressure when seating the new tray

This Drawer Tray Assembly replaces a damaged or worn refrigerator drawer tray to restore proper storage and support for drawer contents. It provides a stable, easy-to-clean surface so drawers slide and seat correctly. What it does:

• Replaces a cracked, warped or broken drawer tray that lets food fall through or catch debris
• Restores a smooth, level surface so the refrigerator drawer opens and closes properly
• Helps contain spills and makes routine cleaning easier
• Fits into the existing drawer housing to support produce, deli items, and other stored foods

• Unplug the appliance or disconnect power before beginning any work.
• Empty the drawer and remove it per the refrigerator's service instructions before replacing the tray.
• Align the tray with the drawer housing and seat it firmly; do not force parts to avoid damage.

This Drawer Tray Assembly replaces a damaged or worn refrigerator drawer tray to restore proper storage and support for drawer contents. It provides a stable, easy-to-clean surface so drawers slide and seat correctly. What it does:

• Replaces a cracked, warped or broken drawer tray that lets food fall through or catch debris
• Restores a smooth, level surface so the refrigerator drawer opens and closes properly
• Helps contain spills and makes routine cleaning easier
• Fits into the existing drawer housing to support produce, deli items, and other stored foods

• Unplug the appliance or disconnect power before beginning any work.
• Empty the drawer and remove it per the refrigerator's service instructions before replacing the tray.
• Align the tray with the drawer housing and seat it firmly; do not force parts to avoid damage.

This right-side refrigerator shelf assembly replaces a damaged or missing shelf to restore safe, level storage and keep foods organized. Tough construction supports deli containers, leftovers and other everyday items. What it does

• Provides a flat, stable storage surface on the refrigerator's right side
• Replaces cracked, chipped or broken shelves that allow items to tip or fall
• Restores original spacing so doors and drawers close and seal properly
• Helps maintain organized storage to prevent spills and contamination

• One right-side refrigerator shelf assembly

• Unplug or power off the appliance before removing or installing parts
• Remove food and clean the area; lift shelf straight out of its supports to avoid chipping
• Handle glass or edges carefully; use two people for heavy or awkward shelves

Note: Shelf is on the LEFT side. 

This shelf net is a replacement mesh shelf designed to support lightweight items and produce in your refrigerator while allowing airflow. It restores storage organization and prevents small items from falling through broken or stretched shelving. What it does:

• Replaces torn, stretched, or missing mesh shelving to restore a secure, breathable shelf surface
• Helps keep small containers and produce stable and contained on the shelf
• Maintains airflow across the shelf area to help even cooling
• Fits into existing shelf brackets or frame to replace the original netting

• Unplug or disconnect power and remove food and containers from the shelf area before installing
• Remove the old net by releasing any clips or fasteners, then position the new net into the shelf frame or brackets
• Install by snapping or fastening into place; avoid overstretching the mesh to prevent premature wear

This shelf net is a replacement door shelf retainer that helps keep small, loose items secure and visible in the refrigerator door. It restores the original storage barrier so bottles, cans, and jars stay in place. What it does:

• Replaces a cracked, stretched, or missing door shelf net that no longer holds items securely
• Prevents small containers and packages from shifting or falling when the door opens
• Restores original appearance and storage function of the door shelf area
• Fits into the existing shelf frame and secures items without blocking visibility

• One shelf net

• Remove all items from the affected door shelf before installing
• Install by snapping or sliding the net into the existing shelf frame per the OEM layout
• No electrical disconnection required, but handle shelves and trim carefully to avoid breakage

This TV cover assembly replaces the outer cabinet panel that protects internal electronics and restores the television's appearance and structural support. Use it to repair cracked, broken, loose or missing covers and to reduce rattling or exposed components. What it does:

• Protects internal circuit boards, connectors and speakers from dust and damage
• Replaces cracked or damaged cabinet panels that cause cosmetic issues or expose components
• Stops loose or rattling panels that can create noise during operation
• Restores mounting points and alignment for screws and internal assemblies

• Always unplug the TV and allow time for internal capacitors to discharge before starting work
• Handle the assembly carefully to avoid scratches; use appropriate screwdrivers for mounting hardware
• Keep track of screws and small parts during removal; replace any damaged fasteners

This tray assembly fits the refrigerator fresh room to support the crisper/drawer area and help contain spills. Replacing a cracked or warped tray restores smooth drawer movement and helps keep produce organized. What it does:

• Provides a stable support surface for the fresh room/crisper drawer.
• Helps contain drips and small spills to prevent messes in lower compartments.
• Restores even drawer sliding and reduces binding, rattling, or misalignment caused by a damaged tray.
• Fits specific fresh room assemblies.

• Unplug the refrigerator or switch off power before servicing to avoid electrical hazard.
• Remove the fresh room/crisper drawer to access the tray; the tray typically lifts or slides out.
• Retain any clips or fasteners and reinstall them with the new tray as needed.

This cover tray is the molded plastic top/cover that protects and contains the unit's internal tray area, helping keep components clean and guiding condensate or collected material into the tray. Replaces cracked, warped or missing tray covers to restore proper containment and appearance. What it does

• Covers and protects the appliance's internal tray area to prevent debris from entering internal components.
• Guides liquid or collected material into the tray for proper containment.
• Helps maintain correct fit and alignment of adjacent panels and parts.
• Common symptom: visible cracks, warping, loose fit or missing cover causing spills or debris entry.

• Disconnect power and remove any water or debris from the tray area before replacing the cover.
• Inspect surrounding tabs and mounting points for damage; replace any broken fasteners for a secure fit.
• Handle the plastic cover carefully to avoid cracking; hand-tighten any screws to avoid stripping.

This Tray Cover Assembly replaces a damaged or missing tray cover to restore a finished appearance and proper protection for the underlying tray area. Designed to fit and align with the original mounting points for a secure fit. What it does:

• Covers and protects the appliance tray from spills, debris, and everyday wear
• Helps maintain correct spacing and alignment of tray components
• Restores the original look where the tray cover is cracked, warped, or broken
• Stops light drafts or minor leaks by resealing the tray perimeter (when part is intact)

• One tray cover assembly

• Install with appliance powered off and water/ice supply turned off if working near dispenser or ice components
• Align tabs and mounting points, then press or fasten according to original hardware—do not force parts into place
• Inspect surrounding clips and screws; replace damaged fasteners to ensure a secure fit

The Deli Drawer Front Cover is an OEM part for LG refrigerators. It provides an attractive facia that protects the internal components of the deli drawer. This cover is designed to integrate with the style and finish of the refrigerator interior. 

Symptoms of a bad Deli Drawer Front Cover include: 

• Cracks, chips, or other visible cosmetic damage
• Discoloration that detracts from the aesthetics  
• The cover is loose, misaligned, or missing
• Difficulty opening or closing the deli drawer

Causes of a bad cover can be normal wear and tear over time from repeated use, as well as accidental drops or impacts that cause cracks or breaks.

This OEM replacement part is also compatible with select LG models.

This Vegetable Tray Assembly replaces a damaged or worn crisper drawer tray to restore a stable storage surface for fruits and vegetables and keep the crisper area organized. Fits where the factory tray sits under the vegetable drawers. What it does:

• Provides a stable shelf for vegetable and fruit bins so drawers slide and store correctly
• Supports crisper drawers and prevents sagging or cracking from everyday use
• Helps maintain proper drawer alignment to reduce rubbing or binding when opening/closing
• Addresses symptoms like a cracked or warped tray, unsecured drawer, or uneven drawer movement

• Disconnect power to the refrigerator before working on internal components
• Remove crisper drawers and any contents; lift out the old tray and set the new tray into the same position
• Handle plastic parts carefully to avoid cracking; do not force parts into place—ensure proper alignment with tracks
• Reuse only the screws/clips that match the OEM locations; replace damaged fasteners before returning the appliance to service

This lamp cover is the replacement light lens that protects and diffuses the appliance's internal lamp, restoring even illumination and shielding the bulb from moisture and debris. It's a direct-fit exterior lens for the lamp assembly. What it does:

• Protects the interior lamp from dust, moisture and impact to help prevent bulb damage
• Diffuses and directs light for even illumination inside the compartment
• Restores a cracked, yellowed or missing lens to improve visibility
• Helps maintain the lamp assembly's proper fit and alignment

• One lamp cover / light lens

• Power off and unplug the appliance before beginning any service
• Remove lamp bulb per manufacturer instructions before replacing the cover to avoid damage
• Use proper tools and handle the lens gently to avoid scratching or cracking
• If mounting clips or screws are worn or missing, replace them separately

This Tray Cover Assembly replaces a damaged or missing cover on the appliance tray to help contain contents and keep the tray functioning correctly. It restores the tray's protective surface and helps prevent spills or contamination. What it does:

• Covers and protects the tray surface to keep contents contained
• Helps direct contents into the tray area to reduce spills
• Replaces cracked, warped or broken covers that no longer seat properly
• Restores a flush fit and appearance for the tray area

• One tray cover assembly

• Disconnect power to the appliance before beginning any service
• Remove the tray or access panel per your model's service instructions to access mounting points
• This part typically snaps or slides into place; light tools (screwdriver) may be needed to remove retaining clips

This rail guide assembly supports and guides a sliding drawer or rack, restoring smooth, stable opening and closing. It replaces a worn or damaged guide to help prevent sticking, misalignment, or detachment. What it does:

• Guides and supports a sliding drawer or rack so it moves smoothly along its track
• Keeps the rack/drawer aligned to prevent tipping or binding
• Reduces noise and rough movement caused by a damaged guide
• Helps restore proper function when the drawer or rack slips off its track or won't close fully

• Disconnect power and remove any items from the drawer/rack before starting
• Remove panels or trim as needed to access the guide; basic hand tools are typically required
• Install the new guide in the same orientation as the original and confirm smooth travel before reassembling

This guide rail assembly replaces a worn or damaged drawer slide to restore smooth, aligned operation and reduce sticking or sagging. It provides stable support for the drawer and helps maintain proper track movement. What it does:

• Guides the drawer along its track for smooth opening and closing
• Restores proper alignment to prevent binding, sagging or uneven travel
• Reduces rattling and scraping noises caused by damaged rails
• Helps the drawer fully seat and latch correctly for secure use

• One guide rail assembly

• Disconnect power and remove contents before servicing the drawer area
• Loosen or remove clips/screws securing the old rail, then slide out and replace with the new assembly
• Use basic hand tools; avoid forcing parts to prevent damage

This freezer door foam assembly restores the insulated core inside a freezer door to help the door maintain proper cold retention and reduce frost. It replaces damaged or compressed foam that can compromise the door's thermal barrier. What it does:

• Replaces the insulated foam core inside the freezer door to improve thermal performance
• Helps reduce frost buildup and uneven temperatures caused by degraded door insulation
• Supports a tighter door fit by restoring original door thickness and shape
• Works with the existing door liner and outer panel to re-establish proper sealing

• Disconnect power to the appliance before starting any repairs.
• Removal of the inner door liner or outer panel is commonly required; handle panels and clips carefully to avoid damage.
• Use proper tools and keep small fasteners organized; inspect door gasket and hardware while the door is open.

This freezer door foam assembly restores the insulated core inside a freezer door to help the door maintain proper cold retention and reduce frost. It replaces damaged or compressed foam that can compromise the door's thermal barrier. What it does:

• Replaces the insulated foam core inside the freezer door to improve thermal performance
• Helps reduce frost buildup and uneven temperatures caused by degraded door insulation
• Supports a tighter door fit by restoring original door thickness and shape
• Works with the existing door liner and outer panel to re-establish proper sealing

• Disconnect power to the appliance before starting any repairs.
• Removal of the inner door liner or outer panel is commonly required; handle panels and clips carefully to avoid damage.
• Use proper tools and keep small fasteners organized; inspect door gasket and hardware while the door is open.

The Door Gasket is an OEM part for LG refrigerators. This gasket creates an insulating barrier to keep cool air locked inside.

Causes of a bad door gasket can involve deterioration of rubber over many years of compression and expansion as doors open and close. Mineral deposits may lead to premature cracking as well.

Symptoms of a bad door gasket include:

• Cool air leaks raising energy costs noticeably
• Frost or condensation buildup along door edges
• Inability to maintain proper interior temperatures
• Premature wear of other components from compromised seal

This OEM LG part is also compatible with some Kenmore models.

This left-side door handle trim restores the finished appearance and edge protection on compatible refrigerators. It replaces cracked, scratched or missing trim to help the handle sit flush and improve the door's cosmetic finish. What it does

• Covers and protects the outer edge of the left door handle area
• Replaces cracked, broken or cosmetically damaged trim pieces
• Helps the handle sit flush and maintain a clean, finished look
• Works with the original mounting points and hardware

• One left door handle trim

• Remove contents from the door and support the door before beginning work
• Use basic hand tools to remove existing trim and secure the replacement to existing screw holes
• Do not force or bend the trim; align to original mounting points to avoid damage

This decor handle is the exterior trim piece for a refrigerator door that restores the original look and grip. It replaces cracked, scratched, or worn trim to improve appearance and provide a finished surface where the handle mounts. What it does:

• Replaces damaged or worn decorative handle trim to restore the appliance's appearance
• Covers and protects the handle mounting area from dirt and wear
• Helps provide a consistent grip surface along the door's edge
• Addresses cosmetic issues like scratches, chips, or fading

• Remove any tape or packaging and match the piece to the door before starting
• Support the door or work with a second person if needed to avoid stress on hinges
• Basic hand tools (screwdriver or nut driver) may be required to remove and reinstall mounting hardware
• Follow OEM instructions and disconnect power only if instructed for models with electrified door components

This hinge cover assembly replaces a damaged or missing hinge trim to protect the hinge mechanism and restore the appliance's finished appearance. It snaps into place over the hinge area for a clean, secure fit. What it does

• Covers and protects the hinge mechanism from dirt and debris.
• Restores the appliance's finished appearance when the original cover is cracked or broken.
• Helps prevent accidental contact with moving hinge parts.
• Common symptom: visible broken or missing hinge trim exposing the hinge.

• One hinge cover assembly.

• Disconnect power (and water, if appliance type requires) before starting any repair.
• Remove any outer panels or trim as needed to access the hinge per the appliance service instructions.
• Handle plastic trim pieces carefully to avoid cracking during removal/installation.

This hinge cover assembly replaces a worn or damaged lid hinge cover to restore a smooth, finished look and protect the hinge area from debris and pinching. It helps keep the hinge area sealed and reduces snagging on the lid edge. What it does:

• Covers and protects the lid hinge and pivot area from dirt and moisture
• Restores a clean appearance where a cracked or missing hinge cover was visible
• Helps prevent clothing or hands from catching on the exposed hinge
• Can reduce rubbing noise caused by contact with a damaged cover

• Basic removal of the lid or access panel may be required; follow for proper disassembly
• Use appropriate hand tools and keep small fasteners secure during reassembly
• Disconnect power (and water for washers) before starting work to avoid injury

This name plate is the exterior emblem that mounts to the appliance's front panel. It replaces a missing, cracked, or faded badge to restore a clean, factory look and cover the designated trim area.

• Attaches to the outer panel to display brand/series identification
• Restores a finished appearance where the original emblem sits
• Direct replacement for a lost, damaged, or worn badge
• Typical symptoms: missing emblem, loose or broken tabs, peeling, or discoloration

• Disconnect power before servicing the appliance
• Carefully remove the old emblem; release any tabs from behind or peel away remaining adhesive
• Clean and dry the mounting surface; remove all residue for best fit
• Align with the recess/holes and press evenly until fully seated

The Handle Assembly is an OEM part for LG refrigerator freezer compartments. It includes the handle and mechanical components that operate the freezer drawer.

Causes of a bad handle assembly can include fatigue from repeated opening and closing motions, damage sustained from heavy loads, or exposure to harsh chemicals over years of use.   

Symptoms of a bad handle assembly include:

• Handles detaching from the drawer front  
• Difficulty smoothly opening and closing the freezer drawer
• Inability to fully open or close the drawer
• Excessive play, wobble, or loose motion in the handle

Replace yours today with this genuine OEM LG assembly to restore effortless operation. This replacement handle is compatible with Frigidaire, Samsung, Whirlpool, and some Kenmore models.

This door foam assembly replaces the inner insulating foam inside a refrigerator door to restore proper thermal barrier and help maintain consistent interior temperatures. It reduces cold spots and helps the door close and seal correctly. What it does:

• Restores the door's insulation layer to reduce heat transfer and help maintain cooling efficiency
• Helps eliminate cold spots, frost buildup, or condensation forming on or inside the door area
• Supports proper door alignment and gasket seating for a tighter seal
• Replaces torn, compressed, or water-damaged foam that can compromise cooling performance

• One door foam assembly as shown

• Disconnect power to the appliance before starting and follow all safety precautions
• Installation typically requires removing the door panel and any inner liners or trim; keep fasteners organized
• Handle with care to avoid damaging the foam or inner door components; do not compress foam when reinstalling

The refrigerator door gasket seals the gap between the door and cabinet to keep cold air in and humid air out, helping maintain temperature, reduce frost and condensation, and restore a tight, reliable door close.

• Creates an airtight perimeter seal to prevent warm air leaks
• Helps stabilize interior temperature and humidity
• Minimizes frost buildup and condensation around the door
• Common symptoms: torn or deformed seal, door not sealing, moisture/frost near door, rising temps

What's included: 1 door gasket Installation notes:

• Disconnect power before servicing
• Allow the new gasket to warm to room temperature; soften in warm water or with gentle, low heat to relax folds
• Remove the old gasket and thoroughly clean the mounting channel/mating surfaces
• Seat the new gasket starting at the corners, then along the sides; ensure it's fully engaged and even all around, and check door alignment/seal

Restore a tight, reliable seal on your refrigerator door with this replacement gasket. A fresh gasket stops cold-air leaks that lead to frost, condensation, and temperature swings—helping your fridge run smoothly and keep food at the right temperature. What it does:

• Seals the gap between the door and cabinet to keep cold air in and warm air out
• Helps maintain consistent interior temperature and humidity
• Reduces frost and condensation around the door opening
• Common symptoms: torn or warped gasket, door not closing flush, moisture at the seal, frost buildup, or the unit running more than usual

• 1 door gasket

• Disconnect power before starting and clear items from the door
• Lay the new gasket flat and gently warm it (hot water or low-heat hair dryer) to relax folds
• Starting at the corners, press the gasket lip fully into the door channel and work evenly around
• Perform a paper-slip test around the perimeter and adjust door alignment if needed; avoid overheating the gasket

The Refrigerator Flipper Assembly is an OEM part for LG refrigerators. This assists in the smooth opening and closing of the refrigerator door. It ensures an airtight seal when the door is closed, preventing cool air from escaping and maintaining the refrigerator's internal temperature. 

Causes of a malfunctioning Refrigerator Flipper Assembly can range from physical damage, such as cracks or breakage, to wear and tear from regular use.

Symptoms of a bad Refrigerator Flipper Assembly include:

• Difficulty in opening or closing the refrigerator door
• A noticeable gap when the door is supposed to be sealed shut
• Increased energy consumption as the refrigerator works harder to maintain its temperature
• Spoilage of food items quicker than expected due to poor temperature regulation

This OEM LG part is also compatible with some Kenmore models.

The Door Bin is an OEM part for LG refrigerators. It provides convenient storage for items accessed regularly, from condiments to snacks.

Causes of a faulty door bin can include plastic cracking from extended usage, broken slide pegs, or a loose assembly. Regular temperature changes may compromise durability over time.

Symptoms of a problematic door bin include:

• Difficulty fully extending or retracting on glide tracks
• Contents are at risk of falling during opening/closing
• Rattling or vibrations while retrieving items

This LG part is also compatible with some Kenmore models.
 

STOPPER ASSEMBLY,DOOR

STOPPER ASSEMBLY,DOOR

This hinge cam fits the door hinge and provides the lift/settle action that helps the door open and close smoothly. Replacing a worn cam can reduce clicking and restore consistent door movement and alignment.

• Provides cam action at the hinge for smooth door travel
• Helps the door seat closed and maintain alignment
• Common symptoms include clicking/knocking at the hinge, rough or uneven door movement, or slight door sag
• Visual wear such as flat spots or grooves on the cam is a typical failure sign

• Disconnect power to the appliance before servicing
• Support the door to prevent injury; remove hinge cover and hardware as needed
• Note the cam's orientation and any washers/spacers and transfer them to the new part
• After installation, verify door operation and gasket alignment; adjust hinge if needed

The Door closer is an OEM part for LG refrigerators, this part prevents the refrigerator door from swinging open too widely. By limiting the door's range of motion, the Door Stop ensures that the door opens smoothly and safely, contributing to the longevity of the appliance and maintaining the aesthetic integrity of your kitchen space.

Causes of a bad Door closer can stem from physical damage, wear and tear over time, or loosening of the component due to repeated use. 

Symptoms of a bad Door closer include:

• The refrigerator door swinging open too far
• Damage or marks on adjacent walls or furniture from the door hitting them
• Increased wear on the refrigerator's hinges due to uncontrolled door movement

This OEM LG part is also compatible with some Kenmore models.

Replace a worn, loose, or broken refrigerator door handle with this complete handle assembly. It restores a secure, comfortable grip so you can open and close the refrigerator door easily while maintaining the unit's original look. What it does:

• Attaches to the refrigerator door to provide a sturdy handhold
• Replaces cracked, broken, or missing handles
• Helps correct a loose or wobbly handle that won't stay secure
• Restores the factory appearance of the door

• 1 refrigerator door handle assembly

• Disconnect power and protect the door surface with tape or a cloth before starting
• Remove any trim/caps as needed and loosen the hidden set screws or mounting bolts on the old handle
• Position the new handle, then tighten fasteners evenly—do not overtighten
• Reinstall any caps/trim and ensure the handle is secure

This connector rail secures and routes electrical connections in the appliance, keeping wiring organized and supporting reliable connections for proper operation. It helps prevent loose harnesses and reduces strain on wiring during use. What it does:

• Provides a stable mounting point for wire harness connectors and plugs
• Maintains correct alignment and spacing of electrical connections
• Reduces stress on wiring to help prevent intermittent connections
• Commonly used when loose or damaged connector mounts cause power or control issues

• Disconnect power and unplug the appliance before starting any work
• Handle connectors and wiring gently to avoid damaging pins or insulation
• Reinstall in the original orientation and secure mounting fasteners snugly

This connector rail is a small mounting piece that holds and aligns a connector assembly inside the appliance, helping maintain a secure electrical or structural connection for reliable operation. It replaces a worn, cracked, or damaged rail to restore proper fit and alignment. What it does:

• Provides a secure mounting point and alignment for the appliance connector assembly
• Helps maintain stable electrical/contact connections by preventing connector movement
• Common symptom indicators: intermittent connections, loose harness fit, or related component misalignment
• Prevents wear on mating connectors by keeping components properly supported

• One connector rail

• Disconnect power (unplug appliance or shut off circuit breaker) before starting
• Access may require removing trim, panels, or nearby components
• Inspect mating connectors and harnesses for damage and replace if needed
• Use common hand tools; handle plastic parts gently to avoid cracking during installation

This slide rail guides and supports a rack or drawer as it moves in and out of your appliance. Replacing a worn rail restores smooth, stable operation and keeps the rack or bin aligned on its track.

• Provides the track and support for a sliding rack, bin, or drawer
• Maintains alignment to prevent tilting, binding, or derailing
• Helps ensure smooth, quiet motion during opening and closing
• Common symptoms: hard to open/close, uneven travel, scraping/clicking noises, rack/drawer popping off the track

• Disconnect power (and water, if applicable) before servicing
• Remove and empty the rack/bin/drawer to access the rail
• Note orientation and transfer any stops/end caps or screws from the old rail if reused
• Secure the new rail and test for smooth travel before reassembly

The Rail, Slide is an OEM part for LG refrigerators. These rails are responsible for allowing shelves and drawers to smoothly glide in and out of the refrigerator compartment. They are designed with precise tolerances and durable materials to withstand frequent use while retaining their smooth operation over time. 

Causes of bad rails can include dents, scratches, or damage accumulated from years of use and repeated opening and closing of shelves/drawers. Wear and tear of moving parts can also cause rails to malfunction. 

Symptoms of bad rails include:

• Shelves or drawers that don't slide smoothly
• Items getting stuck or jammed when trying to remove them from the fridge 
• Gapping or misalignment of shelves/drawers in their tracks
• Noisy or grinding sounds coming from rail areas

This OEM LG part is also compatible with Kenmore models.

This ice maker gear drives the ejector blades that push ice from the tray into the bin. Replacing a worn or broken gear restores proper harvest cycles and stops grinding or slipping during ejection. What it does:

• Turns the ice maker ejector to release ice cubes during the harvest cycle.
• Stops or reduces grinding noises and slipping when the gear teeth are stripped or damaged.
• Helps restore regular ice production when the ejector no longer rotates.
• Works as the replacement driven gear in compatible LG ice maker gear trains.

• Disconnect power before servicing the ice maker to avoid shock or injury.
• Remove the ice maker assembly to access the gear; follow OEM instructions for disassembly.
• Inspect the mating gear, motor shaft, and ejector assembly for wear—replace additional damaged parts as needed.
• Use the matching part number to ensure fit.

This center hinge assembly secures and allows smooth pivoting of the refrigerator's center door, restoring proper door alignment and closing. It replaces a worn or damaged hinge to reduce sagging and improve sealing. What it does:

• Provides the pivot point for the refrigerator's center door, maintaining correct door movement and alignment
• Helps the door close evenly to preserve the gasket seal and internal temperature
• Replaces broken, bent, or worn hinge hardware that can cause door sag or rubbing
• Works with existing hinge pins and mounting points to restore original function

• One center hinge assembly

• Requires basic hand tools; follow manufacturer instructions for removal and installation
• Support the door while removing or installing the hinge to prevent injury or damage
• Ensure all fasteners are tightened securely and door alignment is checked after installation
• Disconnect power if required by the appliance manufacturer before servicing

This center hinge assembly secures and pivots the upper/center refrigerator door, restoring proper door alignment and smooth opening. Designed to replace a worn, bent or broken center hinge to improve sealing and operation. What it does:

• Provides a mounting pivot for the upper/center refrigerator door to ensure correct swing and alignment
• Helps maintain an even door gap for a proper seal and consistent cooling
• Replaces damaged, bent or worn hinge components that cause rubbing, sagging, or noisy door movement
• Works with factory hinge pins and covers to restore original door function

• One center hinge assembly

• Installation requires removing the door and supporting it; have a helper to prevent damage or injury
• Use appropriate hand tools; avoid overtightening fasteners which can bind the hinge
• Inspect adjoining hinge pins and mounting screws; replace if worn for best results
• Disconnect power or follow manufacturer safety steps if working near electrical components

The Spanner Wrench is an OEM replacement part for LG refrigerators. This tool allows you to adjust the door hinges to ensure the doors are level and aligned properly. A well-aligned door is crucial for maintaining the internal temperature and efficiency of the refrigerator, preventing energy loss and ensuring food is stored under optimal conditions.

Symptoms that you might need to adjust the door hinges and potentially need this wrench include:

• Doors not closing properly or sealing tightly
• Visible gaps between the door and the main body of the refrigerator
• The refrigerator tilting or not sitting level

This spanner wrench is also compatible with some Sears/Kenmore refrigerators. 

This upper hinge assembly secures and guides the refrigerator door at the top, restoring proper alignment and smooth opening. Replace a worn hinge to stop sagging doors and improve sealing and operation. What it does:

• Provides the top pivot point for the refrigerator door, keeping it aligned during opening and closing
• Restores proper door clearance and prevents rubbing or misalignment
• Helps maintain a tight door seal to reduce cold air loss
• Addresses symptoms like a sagging or uneven door, noisy movement, or difficulty closing

• Disconnect power to the appliance before beginning repairs to prevent injury.
• Support the door while removing and installing the hinge to avoid dropping or damage.
• Use appropriate hand tools; do not overtighten fasteners to prevent stripping.

Replacement refrigerator door hinge that restores smooth pivoting and proper door alignment, helping the door open and close reliably and maintain an airtight seal to preserve cooling performance. What it does:

• Supports the refrigerator door and allows it to pivot smoothly.
• Replaces worn, bent, or damaged hinges that cause door sag or misalignment.
• Helps reduce noisy or grinding door operation when the hinge is failing.
• Promotes an even door seal to help maintain internal temperature consistency.

• Unplug the appliance and remove food from nearby shelves before starting work.
• Support the door while removing hinge fasteners to prevent dropping or damage.
• Reinstall using the original hardware; align the door and tighten fasteners securely but avoid overtightening.

This PTC thermistor assembly senses temperature changes and sends that signal to the appliance control so the system can regulate heating or cooling. It's a direct-replacement part that restores accurate temperature feedback for proper cycle control. What it does:

• Measures temperature and provides a resistance/voltage signal to the control board
• Helps the appliance maintain correct operating temperature and cycle timing
• Can cause long run times, poor temperature control or error codes when failing
• Works as a monitored safety/feedback device in the appliance's thermal system

• One thermistor assembly (PTC) as shown

• Disconnect power before servicing to avoid shock or damage
• Handle the sensor and wiring carefully; avoid bending or stressing the probe or connector
• Reconnect wiring securely and route harnesses away from moving parts and heat sources

A small retaining pin used to secure moving parts and keep components aligned for smooth operation. Replacing a worn or broken common pin can stop rattling and restore proper fit between linked parts. What it does:

• Holds or aligns two parts together so they move correctly and stay in position
• Helps prevent rattling, looseness, or parts slipping out of place
• Works as a simple mechanical fastener—no electronics involved

• One common pin

• Disconnect power to the appliance before beginning any service
• Keep track of small parts; lay out components in order to aid reassembly
• May require removal of trim or a hinge/retainer to access the pin—use basic hand tools
• If the pin is difficult to seat, do not force; inspect mating parts for damage

This cabinet roller supports the refrigerator and lets the unit roll in and out of place for cleaning or service. Replace a worn or broken roller to restore smooth movement and help keep the appliance properly positioned.

• Supports the base of the refrigerator and enables rolling movement
• Helps with safe positioning and service access without dragging
• Common failure signs: appliance is hard to move, scraping or rolling noises, a flat-spotted/cracked wheel, or a wheel that won't turn
• Replace when the roller is damaged, seized, or missing

• Disconnect power and shut off water supply; protect flooring before moving the appliance
• With help, pull the refrigerator forward and safely support it to access the roller
• Remove mounting fasteners, install the new roller, and reuse original hardware
• Confirm level and smooth movement before returning the unit to its location

The Fan Motor Assembly is an OEM part for LG refrigerators. It is responsible for circulating air throughout the refrigerator and freezer compartments to maintain consistent temperatures. By ensuring proper airflow, the fan motor helps to keep your food fresh and evenly cooled.

Over time, fan motors can wear out or become damaged due to factors such as dust buildup, electrical issues, or general wear and tear from continuous use. A faulty fan motor can lead to uneven cooling, increased energy consumption, and potential spoilage of food.

Symptoms of a bad fan motor include:

• Unusual noises coming from the refrigerator
• Inconsistent temperatures in the fridge or freezer
• The refrigerator running constantly or cycling on and off frequently
• Frost buildup in the freezer section

This OEM LG part is also compatible with Sears/Kenmore.

This compressor damper is a vibration-isolating mount that sits between the sealed-system compressor and the chassis. It cushions the compressor to reduce noise, limit vibration transfer, and help keep refrigerant lines from being stressed.

• Isolates the compressor from the frame to absorb start/stop shock and vibration
• Helps reduce humming, rattling, or buzzing from the back/bottom of the appliance
• Replaces a damper that's cracked, flattened, hardened, or missing
• Can help if the compressor rocks or the unit vibrates excessively

• Disconnect power and pull the unit forward for access; remove rear/service panel if present
• Support the compressor to relieve load on the mounts before removing fasteners
• Match orientation; transfer any sleeves/spacers from the old damper to the new one
• Ensure the compressor sits level and that tubing is not strained before restoring power

This small stopper installs in the refrigerator to limit the travel of a moving component and keep it securely in place. Replacing a broken or missing stopper prevents over-extension and helps maintain smooth, aligned operation.

• Limits the range of motion for a door, bin, or drawer to prevent over-opening or accidental removal
• Helps keep interior components aligned and operating smoothly
• Replace if cracked, missing, or deformed
• Common symptoms: drawer or bin slides out too far, door swings past normal range, or a broken plastic stop is found

• Disconnect power before servicing; remove or support the affected bin/drawer/door
• Note the old stopper's orientation and location before removal
• Transfer and reuse any original screws or clips if applicable
• Snap or fasten the new stopper in place and test for smooth movement

This restrainer is a small retaining clip that helps secure moving or removable components in place, reducing rattles and keeping parts aligned for reliable operation. It's a simple replacement for worn or broken clips. What it does:

• Holds a cover, panel, or door-related component in proper position to prevent shifting
• Reduces noise caused by loose or vibrating parts
• Restores original fit where a broken or missing clip allows movement
• Simple mechanical function — no electrical connections or calibration

• One restrainer

• Disconnect power (and water if applicable) before beginning repairs
• Inspect surrounding mounting points for damage; replace any broken tabs or fasteners
• Typically installs with basic hand tools; align clip and press or snap into place until secure

The Drier Assembly is an OEM part for LG refrigerators. This part removes moisture and contaminants from the refrigerant, ensuring the system operates efficiently and effectively. The drier assembly helps maintain the proper function of the compressor and other cooling components, contributing to the longevity and performance of the refrigerator.

Causes of a bad drier assembly can include clogs from debris, wear and tear over time, or contamination from moisture or refrigerant leaks.  

Symptoms of a bad drier assembly include:

• The refrigerator not cooling properly
• Frost or ice buildup on the evaporator coils
• Increased noise from the compressor
• Reduced efficiency and higher energy consumption
• You should replace the drier assembly if it becomes faulty or damaged.

This OEM LG part is also compatible with select Sears/Kenmore models.

This holder is a small mounting bracket used to secure internal components in place, helping keep parts aligned and stable for reliable operation. It provides a direct, OEM-compatible replacement to restore proper fit and function. What it does

• Secures and supports nearby components to prevent shifting or vibration.
• Restores proper alignment where a worn or broken holder causes rattling or loose parts.
• Helps maintain normal operation by keeping assemblies seated correctly.
• Works behind panels or inside assemblies where a dedicated bracket is required.

• One holder/mounting bracket as shown.

• Installation generally requires removing the panel or access cover where the holder is located.
• Use proper fasteners shown in your appliance; replace any damaged screws or clips as needed.
• Disconnect power before servicing electrical appliances to reduce shock risk.

The Evaporator Fan Blade is an OEM replacement part for LG refrigerators. It is a key component located inside the refrigerator that works to circulate cold air evenly throughout. The fan blade spins rapidly to distribute chilled air from the evaporator coil and refrigeration system, ensuring proper airflow and consistent temperatures across all shelves and compartments.  

Symptoms of a bad evaporator fan blade include:

• Inconsistent or improper interior cooling temperatures 
• Hot or warm spots developing inside the refrigerator
• Strange noises such as clicking or grinding emanating from the rear wall

Causes of a bad evaporator fan blade can be wear and tear over time, an accumulation of dust or debris on the blades restricting airflow, or accidental damage like dents or cracks to the blades affecting their ability to spin smoothly.

This OEM LG part is also compatible with select Sears/Kenmore brand models.

This fan grille assembly houses and protects the evaporator/condenser fan while directing airflow for proper cooling. It restores correct airflow paths and helps reduce unusual noise from a damaged or loose grille. What it does:

• Protects the fan blades from debris and accidental contact
• Directs airflow for efficient cooling performance
• Reduces rattle or vibration caused by cracked or loose grille components
• Maintains proper fan clearance to prevent blade interference

• One fan grille assembly as shown

• Turn off power to the appliance before attempting service
• Remove surrounding panels carefully to access the fan housing; keep fasteners for reinstallation
• Inspect fan blades and motor while grille is removed; replace any damaged components

This fan assembly circulates air within the appliance to maintain steady temperatures and efficient cooling. Replacing a worn or noisy unit restores proper airflow, reduces hot or cold spots, and helps protect other components. What it does:

• Moves air through the appliance and across cooling components for even temperature distribution
• Helps remove heat and moisture as designed for efficient operation
• Replaces a seized, slow, intermittent, or noisy fan/motor assembly
• Common symptoms include weak or no airflow, temperature fluctuations, or abnormal humming/rattling sounds from the fan area

• 1 fan assembly

• Disconnect power before servicing; allow any iced or brittle plastic areas to warm/defrost
• Remove access panels/ducts as needed; note wire routing and take photos for reference
• Transfer any reusable brackets, grommets, or screws from the original assembly
• Ensure the blade spins freely and wiring is clear of the fan path before reassembly and testing

Damper motor support secures the damper motor assembly inside the refrigerator, keeping the air-control damper aligned so it opens and closes correctly. Replacing a damaged support restores proper airflow control and reduces noise. What it does:

• Secures and positions the damper motor assembly so the air-control damper moves smoothly.
• Keeps the motor and damper aligned to help prevent rattling, grinding, or loose motor noise.
• Supports consistent airflow between compartments to assist with even cooling.
• Resolve damper movement problems like the damper not opening or closing fully.

• Disconnect power to the appliance before starting work; remove food and shelves as needed for access.
• Remove the interior access panel to reach the damper assembly; handle plastic tabs and clips gently to avoid breakage.
• Align the motor and damper during reassembly and secure all fasteners; test damper operation before replacing panels and shelving.

This damper motor support replaces a broken or warped mount for the refrigerator's air damper assembly. It holds the damper motor and door securely so the system can meter freezer air into the fresh food compartment.

• Secures and aligns the air damper motor/door within the duct
• Helps ensure proper opening/closing of the damper to regulate airflow and temperature
• Damage can contribute to a warm or too-cold refrigerator and inconsistent temperatures
• May cause clicking or buzzing from the damper area or a visibly loose assembly

• Disconnect power to the refrigerator before servicing
• Access the damper behind the fresh food compartment duct/cover; remove shelves as needed
• Note wiring and orientation; transfer the existing damper motor and door to the new support and reuse fasteners
• Ensure the door moves freely and seals before reassembly; restore power and verify airflow

The SWITCH, MAGNET is an OEM part for LG refrigerators. It is a switch designed to function in conjunction with the magnetic door seal, indicating to the refrigerator when the door is open or closed. This allows the refrigerator to regulate temperatures properly based on door positioning. 

Symptoms of a bad switch, magnet can include:

•  Temperature control issues, with the fridge struggling to maintain proper coolness levels
•  The fridge fails to switch to energy-saving modes when the door is closed 
•  Lights not turning on or off correctly when the door is opened or closed

Replace yours today with this genuine OEM LG part to ensure consistent and reliable temperature control. This OEM LG part is also compatible with Sears/Kenmore.

This door switch cover houses and protects the refrigerator/freezer door switch, keeping the switch secure and aligned so the interior light and door-sensing functions work reliably. It's a direct-fit replacement for damaged or cracked covers. What it does:

• Protects the door switch from impacts, spills, and debris that can cause intermittent contacts or failure
• Keeps the switch properly positioned so the interior light turns on/off when the door opens and closes
• Helps ensure consistent door-sensing for control logic that manages defrost and cooling cycles
• Reduces the risk of moisture reaching the electrical switch components

• One door switch cover

• Power off and unplug the appliance before beginning any repair to avoid shock or damage
• Handle gently to avoid breaking the plastic tabs; some models use snap-in tabs or screws for mounting
• Verify switch alignment and operation before fully reassembling the door trim
• Replace the switch assembly as needed

This sheath-style heater melts frost from the evaporator during automatic defrost cycles to keep airflow clear and temperatures stable. Replacing a failed heater helps stop recurring ice buildup and restore consistent cooling performance.

• Heats the evaporator to melt accumulated frost/ice during defrost
• Keeps air passages clear to maintain proper temperatures
• Helps prevent frost-packed evaporator covers and reduced cooling
• Common symptoms: heavy frost behind the freezer panel, fan noise from ice contact, weak cooling, long run times

• Disconnect power before servicing; allow any sharp edges to be avoided with cut-resistant gloves
• Access is typically behind the freezer's rear interior panel; remove shelves/drawers and panel to reach the evaporator
• Transfer any clips/sensors attached to the heater in the same positions; avoid bending fins or puncturing refrigerant lines
• Ensure connectors are fully seated and the heater is secured before restoring power and monitoring operation

This LED assembly is a backlight strip used to illuminate the display for clear, even picture brightness. Replacing a faulty strip restores proper screen illumination and can eliminate dark spots or missing segments. What it does:

• Provides the LED illumination source behind the LCD panel for even brightness
• Restores lost or uneven backlighting caused by failed LEDs or damaged strips
• Commonly replaces parts that cause dimming, flickering, or no light on power-up
• Connects to the display's LED driver board to receive power and signals

• Disconnect power and remove the display panel before replacing
• Handle the strip and connector carefully to avoid bending or damaging LEDs and flex cables
• Observe ESD precautions and avoid touching LED surfaces or circuit traces
• Reassemble panels and test before finalizing to ensure proper alignment and function

This ice maker lever is the mechanical arm that controls ice production by interacting with the ice maker's on/off and level-sensing mechanism. Replacing a broken or missing lever restores proper operation and helps prevent overfilling or no-ice conditions.

• Acts as the ice maker's shut-off arm to regulate ice production
• Lowers to allow ice making; raises to stop when the bin is full
• Common symptoms: ice maker won't stop making ice, no ice when arm is stuck up, broken/missing lever, lever won't stay in position
• Helps ensure consistent, reliable ice production control

• Disconnect power and shut off water before service
• Remove the ice bin to access the ice maker; gently release the lever from its pivots/linkage
• Note lever orientation; transfer and reuse any original springs, clips, or fasteners
• Reinstall components, restore power, and verify free up/down movement of the arm

This refrigerator ice maker assembly automatically fills, freezes, and harvests ice cubes into the bin. Replacing a failed ice maker restores steady ice production and proper shutoff when the bin is full.

• Automates the ice-making cycle: fills the mold, freezes water, and ejects cubes into the bin
• Monitors bin level and stops production when full
• Helps address symptoms such as no ice production, not cycling/harvesting, or cubes not ejecting
• Can also help with intermittent or inconsistent ice output

• Unplug the refrigerator and shut off the water supply before servicing
• Remove the ice bin, unfasten mounting screws, and disconnect the wire harness
• Transfer existing brackets or covers if required; reconnect harness and secure the assembly
• Align the fill tube with the icemaker inlet; restore power/water and allow up to 24 hours for normal ice production

This sensor PCB assembly detects and relays sensor signals to the appliance control system, restoring accurate sensor feedback and communication when the original sensor board fails or malfunctions. Designed as a direct replacement board. What it does:

• Reads sensor inputs and converts them to signals the main control board can interpret.
• Replaces a failed or intermittent sensor board that causes incorrect readings or sensor-related error codes.
• Can resolve symptoms such as unexpected sensor faults, control errors, or appliances not responding to sensor changes.
• Matches the OEM board function; verify model compatibility before ordering.

• Always disconnect power before servicing to avoid shock or shorting the board.
• Use ESD precautions and handle the PCB by its edges to prevent static damage.
• Ensure all connectors are fully seated and the board is mounted in the original orientation.

This sub PCB assembly is an electronic control board that processes inputs and switches components, coordinating specific appliance functions. Replacing a failed board can restore normal operation and resolve dead controls, error codes, or intermittent, unpredictable behavior. What it does:

• Distributes and regulates control power and switches loads via onboard relays/triacs
• Interprets signals from sensors and the user interface to execute commands
• Coordinates timing and operation of related components per the appliance's program logic
• Failure may present as no power, won't start, unresponsive or flickering display, random beeps, or recurring error codes

• 1 sub PCB assembly

• Disconnect power to the appliance before servicing; verify no voltage is present
• Use ESD protection and handle the board by the edges
• Photograph wiring; transfer connectors one at a time and ensure they are fully seated
• Secure the board with existing fasteners/standoffs; perform any required reset or diagnostic per your model's service info

The Temperature Sensor is an OEM part for LG refrigerators. Also known as a thermistor, is responsible for sensing the temperature changes and providing the necessary feedback to the refrigerator's control board. It helps maintain accurate and consistent temperature levels, ensuring optimal food preservation and efficient cooling.

Causes of a faulty temperature sensor can include wear and tear over time, damage due to electrical issues or exposure to extreme temperatures, or sensor calibration issues. These factors can result in temperature inconsistencies, inaccurate readings, or improper cooling performance of the refrigerator.

Symptoms of a bad temperature sensor may include:

• Incorrect temperature readings on the control panel
• Temperature fluctuations inside the refrigerator
• Overcooling or inadequate cooling of food items

This OEM LG part can also be used on Kenmore/Sears appliances. 

This water line holder secures and routes the refrigerator's plastic water tube so it stays protected and out of the way. Replacing a damaged holder helps prevent kinks and leaks and keeps water flowing to the dispenser and icemaker.

• Anchors and guides the water tube along the cabinet/door to prevent rubbing and kinking
• Helps maintain proper water flow to the dispenser and ice maker
• Replace if the holder is cracked, missing, or the tube won't stay seated
• Symptoms can include leaks or drips near the hinge/backs, slow or no dispensing, or visibly loose tubing

• Disconnect power and turn off the household water supply before servicing
• Access the holder (often behind a hinge cover, kick plate, or rear panel)
• Note tube routing, then release/remove the old holder and seat the tube in the new holder; reuse existing hardware if present
• Restore water and power; check for leaks and normal dispenser/ice operation

The Water Valve is an OEM part for LG refrigerators. This valve is responsible for delivering water from the household supply line into the refrigerator.

Causes of a bad water valve can include mineral buildup restricting water flow over time, wear and tear on internal seals and mechanisms, or damage due to freezing temperatures.

Symptoms of a bad water valve include:

• Slow or inconsistent water pressure at the dispenser
• Drips or leaks at the water line connection points
• The inability to select or use the ice/water dispenser
• Erratic water levels inside the refrigerator

This OEM LG part is also compatible with some Kenmore models.

This mechanical mounting band secures a bracket assembly inside the appliance to keep components aligned and reduce vibration. It restores proper bracket positioning so moving parts run quietly and reliably. What it does:

• Holds a bracket or component assembly in place to maintain proper alignment
• Dampens movement and reduces vibration-related noise or rattling
• Prevents excess wear by keeping parts from shifting during operation
• Helps maintain correct clearances to avoid interference or rubbing

• Disconnect power before inspecting or replacing internal parts
• Remove only the fasteners necessary to access the bracket; keep track of hardware
• Secure all fasteners to the manufacturer's torque or snug specification
• Replace the band if bent, cracked, or missing to restore proper fit and function

This replacement cover filter secures and protects the unit's internal air filters while maintaining correct airflow. It restores the sealed fit of the filter compartment to help the appliance run as intended. What it does:

• Holds the internal filter in place so air passes through the filter media
• Prevents large debris and foreign objects from reaching internal components
• Helps maintain designed airflow path for consistent performance
• Can reduce rattling or vibration caused by a loose or damaged cover

• Unplug the appliance or disconnect power before starting
• Remove the front panel or filter access per the owner's manual to reach the cover
• Align tabs and snap or fasten the cover securely; do not force parts
• Do not operate the appliance with missing or damaged filter cover

This head assembly connects and secures the refrigerator's water filter cartridge, directing water through the filter for dispense and ice systems. It restores proper flow and helps stop leaks when the filter head is faulty. What it does:

• Holds and seals the water filter cartridge in the filter housing
• Directs filtered water to the dispenser and ice maker lines
• Replaces a cracked, leaking, or non-sealing filter head that can cause drips or reduced flow
• Ensures the filter cartridge locks in place for consistent operation

• Turn off the water supply and dispense any remaining water before removing the old head
• Disconnect power to the appliance if needed and follow manufacturer safety instructions
• Inspect and replace any worn O-rings or seals; lubricate O-rings with food-grade silicone if recommended
• Hand-tighten connections, then check for leaks after restoring water and power

This water filter assembly replaces the refrigerator's water filtration module to help restore clear-tasting water and steady flow. Fits models that use the AGF80300705 assembly and installs at the refrigerator water inlet. What it does:

• Filters sediment and common taste/odor contaminants to improve drinking water quality
• Restores reduced water flow caused by a clogged or failing filter module
• Helps reduce visible particulates and cloudiness in dispensed water
• Prevents unfiltered water from reaching the dispenser/ice maker when installed

• Turn off refrigerator water supply before replacing the assembly to avoid leaks
• Hand-tighten connections; avoid overtightening fittings to prevent damage
• Run and discard the manufacturer-recommended initial volume of water after install to flush the system

This genuine replacement filter cover secures and protects the unit's air filter, helping keep the filtration system sealed and operating as designed. Restores proper fit and helps maintain airflow through the filter assembly. What it does:

• Holds the air filter in place and protects the filter media from debris
• Helps maintain correct airflow through the filter chamber for effective filtration
• Prevents gaps that can allow unfiltered air to bypass the filter
• Restores a secure fit if the original cover is cracked, warped, or missing

• One filter cover

• Disconnect power to the appliance before removing or replacing the cover
• Remove the old cover by releasing any clips or tabs, then snap or slide the new cover into place
• Inspect surrounding seal/gasket and filter media for damage while installing
• If clips or tabs are damaged, replace them before operating the appliance