Parts for Frigidaire FRS6B6EEW0: 19 - Ice Maker Parts

Reduces chlorine taste and odor while filtering sediment from your refrigerator's water and ice. Replace every 6 months for best performance. Verify fit.

Water supply tube that routes water through your refrigerator to the ice maker and dispenser. Replace if cracked, leaking, or damaged during moving.

Ice maker clicking or not producing ice? A worn drive gear with stripped teeth is often the cause. This 5-minute fix restores normal ice production.

Ice maker auger not turning or stopping mid-cycle? This ice maker motor drives the auger to dispense ice. Common fix for incomplete rotations.

Spacer component for refrigerator hold switch assembly. Replaces worn, cracked, or missing spacers. Installs between hold switch and mounting plate.

Fix frost buildup in your refrigerator with this defrost thermostat. Controls defrost cycle timing to prevent ice accumulation. Direct-fit part.

Water dispenser won't shut off or ice maker won't fill? This door switch detects when the door closes to control dispensing and cycles. Easy DIY fix.

Ice maker stopped making ice or leaking water? This ice maker assembly fixes production and dispensing issues. Easy DIY install in about 5 minutes.

Ice sits on top and won't fall into bin? This ice maker stripper pushes cubes into the collection bin. Simple DIY repair, just remove and replace.

Secures the ice mold assembly to the support bracket in your ice maker. Replace this mounting screw if it's stripped, missing, or broken during service.

Ice maker not shutting off or making too much ice? A worn lever arm prevents proper shutoff. Simple replacement takes under an hour to restore function.

Specs: 4 - 40 x 0.375

Specs: 4 - 24 x 0.750

Fix water dispensing issues or ice maker problems with this valve switch plate. Controls water flow to dispensers and ice makers in most refrigerators.

This is a Plazcrew #8-10 screw used to fasten appliance panels, trim and components. It replaces lost or damaged screws to restore secure fit and reduce rattling or loose parts. What it does:

• Secures panels, brackets, trim pieces and small appliance components
• Restores proper alignment and prevents vibration-related noise
• Replaces missing or stripped fasteners that cause loose or wobbly parts
• Matches OEM fit for repair and maintenance where this screw is specified

• Disconnect power and follow appliance safety procedures before working
• Use the correct sized screwdriver or driver bit to avoid stripping the head
• Tighten until snug; do not overtighten to prevent thread or component damage
• Keep small parts away from children and work over a tray to avoid loss

Plastic cover that protects the ice maker assembly and directs ice into the bin. Replace if your original cover is cracked, broken, worn, or missing.

Secures and protects wiring harness from strain damage. Replace if cracked, broken, or wires show wear. Verify fit with your model number listed.

Replacement screw for various appliances. Used to secure panels, components, or housing. Replace if stripped, corroded, missing, or damaged hardware.

Secures water, drain, and refrigerant tubing to prevent movement and wear. Replace if tubes are loose, vibrating, or damaged. Verify fit with model number.

Directs water from the inlet valve to the ice maker fill cup. Replace if cracked, kinked, frozen, or causing leaks inside your freezer compartment.

Ice maker stopped working or water dispenser not flowing? This refrigerator water valve controls water to both. Easy 10-20 minute DIY fix with video.

Replacement mounting screw for refrigerators and ice makers. Secures panels, brackets, and internal components. Needed when original is missing, stripped, or damaged.

Secures refrigerator hoses to fittings with spring tension to prevent leaks. Replace when clamp loses grip or shows rust. Verify fit with model number.

If your icemaker won't turn on or off, or the switch sparks or clicks but doesn't respond, this power switch restores reliable control. Direct fit.

Air deflector for refrigerator icemaker. Snaps onto the ice stripper to direct airflow. Replace if cracked, broken, or missing from your freezer.

This 1/4" compression nut and ring is used to connect the water supply line to the water valve inlet. Can be used anywhere a 1/4" compression fitting is needed.

Inlet valve to door

Secure hoses and wires inside your refrigerator with this nylon clamp. Replace if broken or cracked to prevent loose connections. Verify fit by model.

Water valve cap for side-by-side refrigerators. Covers and protects the water inlet valve connection. Replace if cracked, broken, or missing.

Guides ice from the ice maker into the bin to prevent spills and overflow. Replace if cracked, broken, or missing to restore proper ice flow.

Seals internal refrigerator components to prevent air leaks and moisture intrusion. Replace when worn to maintain proper airflow and temperature control.

Replace your refrigerator's water inlet tube when cracked, split, or leaking. Connects water inlet valve to internal filter or dispenser system.

Water inlet tube connects the water valve to your ice maker. Replace if cracked, leaking, or damaged. Installs at the back of your refrigerator.

Ice maker stopped making ice or leaking water? This ice maker assembly fixes production and dispensing issues. Easy DIY install in about 5 minutes.