Parts for Frigidaire PHT189WHSM2: 11 - Ice Maker Parts

Reduces chlorine, lead, and contaminants in your drinking water and ice. Replace every 6 months for optimal performance. Verify fit by model number.

Water inlet tube connects the water valve to your ice maker. Replace if cracked, leaking, or damaged. Installs at the back of your refrigerator.

This name plate is the replacement identification label that mounts to the appliance exterior to display model, rating and manufacturing information — making it easier to identify and service the unit. What it does:

• Provides the factory identification label with model and rating details for accurate appliance identification
• Restores legibility when the original plate is scratched, faded or missing
• Helps technicians confirm correct replacement parts and service information
• Supports resale value and safety by ensuring required labeling is visible

• One replacement name plate

• Always disconnect power and shut off gas or water supply before servicing
• Clean and dry the mounting surface before installing to ensure proper adhesion or fit
• This part replaces the visible identification plate only; the part number on the plate matches your unit before installation
• If mounting hardware or adhesive is required, use the method specified by your model's service instructions

Ice maker clicking or not producing ice? A worn drive gear with stripped teeth is often the cause. This 5-minute fix restores normal ice production.

Mounting plate secures internal components in your freezer. Replace if cracked, warped, or missing to restore proper support and stability.

Ice maker stopped making ice? This complete ice maker assembly resolves no ice production and leaking issues. Easy DIY install with video guide included.

Spacer component for refrigerator hold switch assembly. Replaces worn, cracked, or missing spacers. Installs between hold switch and mounting plate.

Fixes freezer not cooling properly or running too cold. This defrost thermostat restores proper temperature control. Direct replacement, moderate DIY.

Water dispenser won't shut off or ice maker won't fill? This door switch detects when the door closes to control dispensing and cycles. Easy DIY fix.

Support plate for freezer interior mounting. Replaces cracked, broken, or missing support plates that compromise shelf or component stability.

Ice maker stopped making ice? This complete ice maker assembly resolves no ice production and leaking issues. Easy DIY install with video guide included.

Ice won't eject from maker? This ejector arm pushes cubes into the bin when prongs break. Common fix for ice piling up on top of the ice maker tray.

Ice maker stopped making ice? This complete ice maker assembly resolves no ice production and leaking issues. Easy DIY install with video guide included.

Replacement mounting screw for freezers and refrigerators. Secures interior components and panels. Order now if your original screw is missing or stripped.

Note: The ice stripper is no longer available. Order complete icemaker by model number.

Ice maker not shutting off or making too much ice? A worn lever arm prevents proper shutoff. Simple replacement takes under an hour to restore function.

Mounting screw for freezer and refrigerator assembly. Secures panels, shelves, or internal components. Replace if stripped, missing, or damaged.

This replacement screw secures appliance components so panels, trim, or brackets stay fastened and aligned. Use it to replace lost or stripped fasteners and stop rattling, loose panels, or parts that won't sit flush. What it does

• Fastens panels, trim pieces, brackets, and small components to the appliance frame
• Replaces worn, stripped, or missing screws that cause rattling or gaps
• Restores secure mounting and alignment for doors, controls, or interior parts
• Works wherever the OEM screw 5304456677 is specified

• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug; do not over-torque to prevent thread or part damage
• Compare new screw to the original to ensure correct fit before installation
• Disconnect power to the appliance if working near electrical components

Timing adjustment screw for refrigerator ice makers. Controls water fill duration. Replace if stripped, missing, or damaged during ice maker maintenance.

Mounting plate that secures the valve switch inside your freezer. Replace if the original plate is cracked, broken, or missing to properly support components.

Replace a worn, broken, or missing door spring in your refrigerator. This spring provides tension for smooth door operation and proper closure.

Replacement screw for securing refrigerator panels, brackets, and trim. Restores proper fit and reduces rattling from loose or missing fasteners.

Replaces your refrigerator's ice maker cover if cracked, broken, or missing. This protective cap installs on the ice maker assembly in your freezer.

Secures and protects wiring harness from strain damage. Replace if cracked, broken, or wires show wear. Verify fit with your model number listed.

Replacement screw for various appliances. Used to secure panels, components, or housing. Replace if stripped, corroded, missing, or damaged hardware.

Secure hoses and wires inside your refrigerator with this nylon clamp. Replace if broken or cracked to prevent loose connections. Verify fit by model.

Replaces cracked, frozen, or leaking ice maker fill tube. Directs water from supply line into ice maker tray. Common replacement for damaged tubes.

Replacement screw for securing panels, components, and assemblies in appliances. Needed when original screws are stripped, lost, or damaged during repair.

Leveling bracket that mounts and supports the ice maker assembly inside your refrigerator. Replace if bracket is cracked, broken, or missing.

Secures refrigerator hoses to fittings with spring tension to prevent leaks. Replace when clamp loses grip or shows rust. Verify fit with model number.

Factory fastener that secures panels, brackets, and internal components. Replace missing, stripped, or corroded screws to restore tight fit and eliminate rattling.

This water inlet tube directs incoming water from the household supply to the refrigerator's dispenser and ice-making system, restoring proper flow and preventing leaks at the appliance connection. Ideal when the original tube is cracked, clogged, or damaged. What it does:

• Carries water from the home supply line into the refrigerator's internal water system.
• Helps ensure the ice maker and dispenser receive a steady water flow.
• Commonly replaced when you see leaks at the inlet, reduced or no water flow, or visible tube damage.
• Works with the refrigerator's inlet fittings and seals to maintain a watertight connection.

• Disconnect power to the appliance and shut off the water supply before starting.
• Inspect and replace any worn seals or fittings when installing the new tube.
• Avoid sharp bends or kinks; route the tube as the OEM tubing was positioned.
• Turn the water back on and check all connections for leaks after installation.

This replacement label provides the appliance's identification and rating information so you can restore clear model, serial, and safety marking visibility. It helps owners specifications and service details at a glance. What it does:

• Displays model, serial, and electrical rating information for the appliance
• Restores worn or missing safety and regulatory markings
• Keeps identification visible for warranty and service calls

• One replacement identification/rating label

• Clean and dry the mounting surface before applying; remove any dirt, grease, or old adhesive
• Align carefully and press firmly to ensure full adhesion; allow adhesive to set per room temperature conditions
• Do not place over vents, moving parts, or control openings
• For safety, disconnect power to the appliance before accessing internal areas to reach the original label location

This 1/4" compression nut and ring is used to connect the water supply line to the water valve inlet. Can be used anywhere a 1/4" compression fitting is needed.

Seals internal refrigerator components to prevent air leaks and moisture intrusion. Replace when worn to maintain proper airflow and temperature control.

Replaces cracked, leaking, or melted ice maker fill tube that carries water from the supply line to the ice mold. Installs in the freezer compartment.

Ice maker stopped making ice? This complete ice maker assembly resolves no ice production and leaking issues. Easy DIY install with video guide included.