Parts for Craftsman 944415361: Ignition / Carburetor Parts

The ignition coil module is a part found in chainsaws that electricity runs through. It also helps transmit electricity to the spark plug so the tool works properly. The electricity builds sparks in the plug which ignites the fuel in the engine to ensure the chainsaws can power on. If the ignition coil fails, it will prevent the saw from starting since the spark plug is unable to operate. Testing the ignition coil is simple and can be done in 15 minutes or less. Remove the chainsaw's spark plug wire and then take out the spark plug. Remove the recoil starter on the side and look for the kill switch. This needs to be disconnected from the harness before the starter assembly is replaced. Spread the spark plug gap and place the boot on top of it. Next, pull the start rope while watching the plug. If there is no spark, the ignition coil module needs to be replaced. This is a genuine OEM part that comes directly from the manufacturer. It is compatible with chainsaws made by Poulan, Poulan Pro, and Craftsman. It comes as a single individual ignition coil. An ignition coil tester can be useful to have for replacement.

This screw is designed to be used in many different chainsaws to connect and hold together various components. The screw can be used on its own or placed with a nut in a pre-drilled and threaded hole. If a nut is going to be used, it is best to choose one with the same threading and finish as the screw that will be used. A screw can become damaged in many ways that will require a replacement. Corrosion, excessive stress, or high temperatures may weaken the screw. In some cases, the damage can cause it to break or become loose and no longer properly secure other components of the chainsaw. A visual inspection can help determine if corrosion is present or the screw is damaged or broken. If the screw is stripped, a bolt remover may be needed to remove it to make the replacement.This screw is a genuine OEM replacement part provided directly from the manufacturer. It is sold as an individual component. The screw is compatible with chainsaws created by Poulan, Poulan Pro, Craftsman, and Husqvarna. A screwdriver is needed to replace, remove, or install the replacement part.

This part is a replacement ground strap. This is a genuine OEM part made by Husqvarna and has been sourced directly from the manufacturer. This part can be used to replace a damaged or defective ground strap in a variety of chainsaw models. The ground strap works to ground a live current and is an important safety feature. Equipment should not be operated without a working ground strap. This part connects to the ignition module of the chainsaw, which transfers an electrical current to the spark plugs. It is always recommended that the appropriate safety precautions are adhered to when attempting to fix any power tools or machinery. For more accurate information on how and where to install this ground strap, the appropriate owner's manual and included diagrams should be referenced.As an authentic replacement part, this ground strap is suitable for use on several different models of chainsaws manufactured by Husqvarna, Poulan, and Jonsered. This is a genuine part made of high-quality, durable materials and is sold individually.

This wire harness assembly is an authentic replacement for chainsaws. It is supplied from the manufacturer. The wire harness assembly connects to the ignition module. It is made of two wires. One of the wires carries the power from the coil to the switch, while the other wire attaches to the engine ground on one side and has a switch contact on the other side. The wires have a rubber insulated coating that helps to protect them from high heat. These wires can suffer damage in many ways. They could become frayed or cut, they could have been subject to extremely high temperatures, and more. When they are damaged, it can cause a continuity loss in the circuit which can shut off the saw. Owners should look for broken or frayed wires. They can also use a multimeter to check the wires for continuity. If there are issues, the wires should be replaced right away. The chainsaw wire harness assembly is a genuine OEM replacement part for use with chainsaws. The assembly is sold individually. It will work with select chainsaws from Craftsman, Husqvarna, Poulan, and Poulan Pro.

This replacement part is a cylinder shield. This is a genuine replacement part made by Husqvarna. This shield is made of durable material to keep the cylinder of the lawnmower safe during use. This cover is responsible for repelling flying debris or other objects to ensure that the engine runs smoothly and effectively. A new cylinder shield might be needed if the current one is at all damaged. This might include being dented, cracked, or bent. If the shield is unable to completely cover the cylinder it would be best to replace this part as soon as possible. The repair should be simple as most shields are able to click easily into place. This part is a genuine OEM replacement part to ensure proper fit. It is also sold individually and is sourced directly from the manufacturer.

This part is a lever ignition switch, often called an ignition lever. The lever ignition switch is used on chainsaws. This part is a switch starts and stops the chainsaw. Remember to wear gloves when operating or performing care and maintenance on any outdoor power equipment.A new lever ignition switch may be needed if the engine will not start, if the engine suddenly dies, if the chainsaw only runs intermittently, or if the kill-switch is not engaging. A Phillips screwdriver, Torx driver, flat-head screwdriver, and ratchet/socket set will be needed to perform this replacement.This lever ignition switch is a genuine Husqvarna part. It is sold individually. This particular lever ignition switch is compatible with gas chain saws that are manufactured by Husqvarna, Poulan, and Jonsered.

This part is a replacement spring ignition switch. This is a genuine OEM part made by Husqvarna and has been sourced directly from the manufacturer. This part can be used to replace a broken or faulty spring ignition switch in a variety of gas chainsaw models.This part is essential for applying tension to the throttle control lever. If the spring ignition switch is malfunctioning, the chainsaw will not work properly, and the user will not have sufficient control over the throttle. When working on or near an engine, ensure the equipment is powered off and completely cooled down before starting any work. Proper tools are required to replace this part. For more accurate information on how and where to install this spring ignition switch, the appropriate owner's manual and equipment diagrams should be referenced. As an authentic replacement part, this spring ignition switch is suitable for use on several different models of gas chain saws manufactured by Husqvarna, Poulan, and Jonsered. This is a genuine part made of high-quality, durable materials and is sold individually.

This is a genuine OEM replacement choke lever is sourced from the manufacturer for use on chainsaws. The choke lever is triggered by the choke knob to open the choke when cranking the chainsaw's engine. The choke is used to limit airflow into the carburetor when starting the engine. In cold temperatures, this enriches the mixture of fuel to air and forces this into the carburetor.Normal wear and tear can cause the choke lever to crack and possibly break. Accidents such as dropping the chainsaw may also cause the lever to break. Without the choke lever, the choke cannot be engaged when needed and the engine may not start in cold weather. When this occurs, the lever will need to be replaced. This is a simple repair that requires a Phillips head screwdriver, flat head screwdriver, ratchet and socket set, and torque drivers. Remove the top cover to access the choke knob. Remove the cover from the air filter and the ignition switch lever. Disconnect the choke from the carburetor linkage and remove the lever. Install the new lever. Connect the new lever to the carburetor linkage. Reinstall the ignition switch lever, air filter cover, and outer covering. This choke lever is designed for use on chainsaws. It is sold individually. This choke lever is manufactured for Poulan chainsaws.

This quality air filter cover protects and secures the air filter to the chainsaw. If the air filter cover is not in place, the air filter could become excessively dirty or damaged. Through use or impact, the air filter cover can become damaged and may need to be replaced. A quick visual inspection will tell whether there are holes or cracks in the cover that necessitate a replacement.This air filter cover replacement requires no tools. The air filter cover comes with small tabs that can be used to secure it in place over the air filter. Tug on the original air filter cover and pull it out of its place before pressing the new one into place using its plastic tabs. Reassemble any other components before use.This is an authentic OEM replacement part that is directly sourced from the manufacturer. It is sold as an individual component. The air filter cover is designed to be used with chainsaws manufactured by Poulan, Poulan Pro, and Craftsman.

This is an air filter that is intended for use with chainsaws. An air filter is designed to filter the air to remove any dust, debris, or other harmful contaminants that could harm the engine. A new air filter will be needed with regular use, and should generally be replaced as a part of normal care and maintenance on the chainsaw. Over time, the air filter will become clogged, which will inhibit airflow through the machine. At this time, it is essential to change out the air filter to ensure proper operation. Never perform care and maintenance on an outdoor power equipment machine that is powered on. Remember to wear gloves when operating or performing care and maintenance on any outdoor power equipment. This air filter is a genuine OEM Husqvarna part. It is sold individually. This specific air filter is compatible with chainsaws that are manufactured by the Husqvarna and the Craftsman brands.

This screw is a genuine MTD part, sold individually. A screw can be used as a replacement part in a chainsaw. The purpose of this genuine OEM part is to pierce and rotate into one or more components such that the stability and placement of those components can be secured within the external or internal machinery of the chainsaw.The screw in a chainsaw might be lost or damaged within the typical lifespan of the appliance. If the screw is lost or damaged, it should be immediately replaced by this genuine OEM replacement part; the same replacement should occur if the screw has suffered enough damage to reduce or negate its typical functionality. Refer to the manual for detailed instructions.This OEM part is a genuine replacement that is sold individually and sourced directly from the manufacturer. This screw is compatible with the following outdoor appliance brands: Husqvarna, Craftsman, Poulan, and Poulan Pro.

The chainsaw carburetor mixes air and gas before this mixture makes its way to the engine. If this is not working correctly, the engine receives a less efficient gas supply or no gas supply at all. If your chainsaw has a full tank of gas but will not start or stops just after starting, the carburetor may need to be replaced. While carburetors can be cleaned to get them working again, they often need to be replaced if they have become too clogged. Depending on what you can reuse from your old carburetor, you may need to order new gaskets as well to ensure an airtight seal. A screwdriver, a nut driver, and a socket wrench set may be needed to complete this repair. This chainsaw carburetor is sold individually from other parts, but it does include the primer bulb. It is compatible with Craftsman and Poulan chainsaws. This chainsaw carburetor is a genuine OEM part.

This is a complete set of gaskets designed as a set to make the most of chainsaw maintenance and repair. This OEM gasket kit contains seven unique gaskets that should be replaced whenever a chainsaw's motor is serviced or repaired. Gaskets are designed to ensure that fuel remains where it is intended within the engine and parts and does not leak or seep into other areas. The pressure is maintained in the machine through the use of effective gaskets and seals. This is a complete kit and comes with every gasket needed for chainsaws made by Craftsman, Husqvarna, Poulan, and McCulloch, among others. It does not come with any associated parts necessary for full chainsaw maintenance and will require disassembly of several systems to install the new gaskets.

This product is the chainsaw's engine cylinder, which holds fuel ignited by the spark plug. It fits into the existing chamber and houses the pistons during use. It is attached to the carburetor for fuel injection. The spark plug is set within it to ignite the fuel. This part has to be screwed securely into place prior to use and requires lubrication for the engine to run smoothly. If the engine suffers from poor fuel ignition, or leaking fuel, the cylinder may be cracked. When installing the new part, a few holes may require a tap to fit each specific machine. Pistons and bolts sold separately. Existing parts should be cleaned prior to use. This OEM replacement part is sourced straight from the manufacturer and works with certain models of Poulan and Husqvarna small engines.

This muffler kit can be used as a replacement part in chainsaws. It provides all the necessary pieces for muffler installation. On chainsaws, the muffler's purpose is twofold: it quiets noise, and it redirects the chainsaw's exhaust away from the user. The clearest sign that a muffler needs to be repaired or replaced is a change in noise level. Strange odors are another symptom of a damaged muffler, in which case the muffler should be removed and replaced immediately. A final symptom of damage in a muffler is reduced fuel economy, which can be attributed to a number of other factors but can point to muffler damage if paired with a change in noise or a strange odor. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. This muffler kit is a genuine Husqvarna part, sold individually. It is compatible with the following brands: Husqvarna, Poulan, and Craftsman.

This is a genuine replacement spark arrestor kit that is used with certain styles and models of chainsaws. The spark arrestor kit will attach to the cylinder gasket and is designed to catch any particles that are coming from the engine that are hot or likely to create a fire risk. This ensures that the internal combustion engine can operate effectively. When the spark arrestor is damaged or worn, or if pieces go missing, it will not be able to give the engine the protection from flammable debris that it needs. A replacement is necessary for the safe operation of the chainsaw. This OEM authentic spark arrestor kit is manufactured by Poulan and compatible with over 50 of the chainsaws that are made by the brand. This kit includes the screen, the metal arrestor, and the nut that connects the components and helps secure the entire assembly to the engine's cylinder gasket. This part replacement will require a nut driver and a set of pliers. Allow the engine to cool completely and always disconnect the spark plug when performing engine repairs or internal replacements. Owners will want to wear gloves for hand protection, as well.

This muffler bolt is an OEM replacement part that is sourced directly from the manufacturer. These bolts secure the muffler cover to the muffler on chainsaws, trimmers, and other small engines found in lawn and garden machines. Regular use can cause the bolts to loosen and possibly fall out of the cover. The muffler cover requires two bolts to secure it. These bolts have a hexagon-shaped head and require a hex key or Allen wrench to install or remove them from the cover.The muffler on small engines softens the noise coming from the machine. Being exposed to loud noise for long periods can lead to hearing damage. The muffler helps lessen this risk. The muffler cover protects the inner parts of the muffler. Rain, snow, dirt, and debris can cause rust and corrosion. Use the Allen key or hex wrench to loosen the muffler bolt if it is rusted or bent. Install the new bolt and tighten it using the hex wrench. The muffler bolt is made of high-quality steel and it sold as an individual part. The muffler cover requires two bolts to secure the cover. This bolt is compatible with chainsaws, hedge trimmers, and other small engines manufactured by Poulan, Weed Eater, and Husqvarna.

This replacement part is an insert transfer and is intended for use in a variety of lawn equipment. This is a genuine replacement part made by Husqvarna. Insert transfers are small but very important to many different appliances like chainsaws. These parts reduce friction inside of the motor and piston. Without this part the engine could become damaged.A new insert transfer might be needed if the user hears noises coming from the equipment that are not normal. If there is excess heat coming from inside the appliance this might also be the cause. It is common that insert transfers become stripped overtime due to normal wear and tear. Be sure the equipment is completely powered down and cooled off before attempting to repair an appliance. For more detailed instructions on how to install this specific part, see the owner's manual. This is an OEM part sourced directly from the manufacturer. It is sold individually. This replacement part is compatible with different types of lawn equipment made by Husqvarna.

This ball bearing and seal are used in a range of chainsaw models. It acts as part of the blade assembly and is designed to both lessen friction and stabilize moving parts. This bearing is also set within a race and the entire race/bearing/seal assembly must be replaced at the same time. The bearing is encased with a rubber seal, which prevents fuel leakage and keeps the engine working smoothly. It does not impede the bearing as it turns. Ball bearings are placed in high contact areas and wear down due to friction. They need to be regularly replaced for optimal performance. If the engine shows difficulty while running, or is louder than usual, the seal or bearing may have worn down. This OEM replacement part is sourced from the manufacturer and works with certain models of Poulan small engines, including the Poulan/Poulan Pro 2900, and Husqvarna chainsaws. This part replaces parts 530019259 and 530047827, both of which are obsolete.

This piston is an important part of the internal function of a chainsaw. The piston moves in and out of the cylinder while pushing the connecting rod that turns the crankshaft. Without a functioning piston, the chainsaw will not work. The piston could fail due to natural wear and tear, or it could become damaged because of other issues with the chainsaw. Corrosion could also be a problem. Regardless of what causes the pistons to have problems or to break, owners need to replace them as soon as they see a problem. This is a genuine OEM replacement piston kit. The kit includes a piston, piston pin, piston ring, and two piston pin retainers. The piston kit is only for use with chainsaws. It is compatible with several brands including Husqvarna, Poulan, Poulan Pro, and Craftsman.

This replacement part is a transmission insert and is intended for use in different types of lawn equipment. This is a genuine replacement part made by Husqvarna. This transmission insert is used in chainsaws and allows the transmission to operate smoothly. A new transmission insert might be needed if the current one is damaged or missing. If there are noises coming from the inside or the appliance won't stop or start properly, it might be due to a bad transmission insert. Be sure the engine is completely turned off before attempting to start this repair. Because this part is close to other areas that can be dangerous, it is recommended that the user wear work gloves during the job to prevent injury. This transmission insert is a genuine OEM replacement part and is sourced directly from the manufacturer to ensure proper fit. This part is sold individually.

This part is a replacement screw. This is a genuine OEM part made by Husqvarna and has been sourced directly from the manufacturer. This part is intended to replace a defective, misplaced, or stripped screw in outdoor power equipment. Screws are a standard piece of equipment hardware with different uses. They help to secure parts of the equipment together properly. If a screw becomes corroded, stripped, misplaced, or is otherwise defective, then it should be replaced. Wear work gloves and check that equipment is powered off and cooled down before starting the repair process. For more accurate information on how and where to install this screw, the appropriate owner's manual and equipment diagrams should be referred to. This screw is a genuine OEM part made of durable metal and is sold individually. It is suitable for use with small engine outdoor power equipment models that have been manufactured by MTD, Craftsman, and other brands.

This part is specifically designed for use with chainsaws. This tube intake is designed to create a flexible path between the adapter and carburetor, ensuring efficient equipment functionality. If the tube intake becomes worn, detached, or cracked, the carburetor may not be able to properly mix the correct ratio of air and fuel, causing the engine to misfire or underperform. This tube intake is a genuine OEM replacement part that has been sourced directly from the manufacturer. This tube intake is designed to fit various different models of Husqvarna and Poulan chainsaws. Please note this part is sold individually.